EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

11020052994 Kenmore Washer - Instructions

All Instructions for the 11020052994
91 - 105 of 1171

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Will Not Agitate
4 of 6 people found this instruction helpful.
  • JOSE from SOUTH SIOUX CITY, NE
  • Really Easy
  • 15 - 30 mins
  • Socket set
I always tought that I could never fix my own washer with so little time and with less than $25 dollars so good that our washer is working like new once again thanks to partselect. . . . I will be happy to buy from you any time.
Was this helpful?
Thank you for voting!
Top agitator did not work
3 of 3 people found this instruction helpful.
  • George from Danbury, WI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
I removed the cover for the softener dispenser on the top of the agitator. Then reached in and removed the cover of the nut and washer which was very sticky and sealed with an o-ring. This took a bit of pressure. Then used a socket wrench with an extension to loosen the bolt and took the whole agitator out of the machine. Then I set the a gitator on the floor and with a fine 12 inch long screw driver released the catches while turning and pulling the agitatior with my other hand and holding the lower agitatior on the floor with my feet. I then turned the upper part over and removed the cogs and holding mechanism.
Then I reversed the process after replacing the cogs with the new part. 25 minutes total.
Was this helpful?
Thank you for voting!
shaking on spin cycle
13 of 33 people found this instruction helpful.
  • Paul from Milwaukie, OR
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Removed the outside body of washer. Used 1/2 plywood between drum and wear pads to make space to pry out pads with screwdriver. Replaced suspension springs and tub spring (use waterproof grease on end of springs. Put washer back together and tested. Problem solved washer not walking all over floor anymore. Thanks for you help.
Was this helpful?
Thank you for voting!
Motor runs, but tub does not spin or agitate
3 of 3 people found this instruction helpful.
  • Danny from Woodstock, GA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Woulkd have taken alot less time had I not taken off the control board, back...etc. Laying the unit on its back is perfect. Took it out into the garage when I could have done it in the laundry rooom with very little water loss.
1. Removed all hoses connected to top of motor. This was not very easy since the spring clamps had been in the same place for 20+ years. Also removed all wire harness connected to and from the motor.
2. Removed metal clamps from top of motor unit, and removed the plastic "valve".
3. Removed screws holding in clamps on each side of the motor used to hold motor on motor plate. Removed motor. Trick is to make sure that the back clamp stays in place...makes it a little easier when you go to re install.
4. Cleaned out around agitator shaft, and fitted one side of the coupling and the neoprene type joiner on to the agitator shaft.
5. Fitted other side of coupling on to motor...This is where it got a little tough......and then placed motor unit on the motor plate, making sure to line up teeth to neoprene joiner.
6. Replaced clamps on each side of the motor and screwed in nuts holding them in place.
7. Replaced plastic "valve" and the clamps that hold it in placed...back one is a little tough.
8. Reattached hoses to "valve" and hooked all wire harness back into place.
9.Tested perfect...little burning smell on first spin....but works great now!!
Was this helpful?
Thank you for voting!
Broken Coupling
3 of 3 people found this instruction helpful.
  • DEREK from ASHEVILLE, NC
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
Disconnect power & water then drain hoses.
We flipped the washer on it's side to gain access to the bottom. There was no need to take off the back panel. Keep a 5 gallon bucket and a few rags handy for the extra water in the pump line.
Disconnected the wiring harness. Removed the brackets holding the motor. It's a little tight o n the back bracket. It has a 1/4" hex nut on the back side, so I used a 1/4" drive socket (see: small). Removed the bolts holding the gear case (this makes it a lot easier). Disconnected the pump hose and rotated the motor & gear box and pulled forward. This gives you access to the coupling. Remove the broken part. Clean the area for debris. NOTE: each part of the coupling has 3 fingers (these are what breaks off), so check to make sure you get all broken parts. Insert the new coupling. It has 3 parts; the plastic fittings go on tight and need to be snug to the shaft. Use a screwdriver handle on the center and tap down with a small hammer. Spray silicone on the rubber coupler to allow a little better slide.
Reverse the process. Line the gear box and motor up and push back into the tub assembly. We used 2 people to do this. It's easier to have someone stand over it and hold / rotate the gear box while the other one can align the motor & bolt everything back on.
It took us an hour, however, if you were doing a couple you could get it down to 30 min. flat.
Go wash your clothes!
Was this helpful?
Thank you for voting!
Machine made loud banging noise and vibration when running and tub ran off center
3 of 3 people found this instruction helpful.
  • Albert from ROSELLE, IL
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Disassembled top control console and surrounding sheet metal cabinet per the video from this site. i then used a screw driver to carefully pry up each wear pad location individually and inserted the wood wedge. to about 1 1/2 inch height. rwmoved the old wear pads and popped in the new pads one by one. Closed up the unit and tested the machine . It ran like new. No more noise or viberation
Was this helpful?
Thank you for voting!
Leaking water inlet hoses.
4 of 6 people found this instruction helpful.
  • Helen from NASHUA, NH
  • Really Easy
  • 30 - 60 mins
Removed the old hoses and screwed on the new hoses.
Was this helpful?
Thank you for voting!
The washing machine was leaking.
3 of 3 people found this instruction helpful.
  • Matthew from Affton, MO
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
I followed the provided video for changing the centerpost gasket.

I successfully completed the repair. I will say that I had challenges at almost every step. Getting the inner basket off the centerpost was difficult, as was rocking the outer tub upward from the base.

If a man is somewhat handy, this is a doable repair. Be patient and take your time. The video is very helpful and I don't think I could've done the repair without it. It's a pleasure to watch an expert like Steve.

It's gratifying to successfully repair a major appliance such as a washing machine and I look forward to many more years of reliable service from this well-built appliance.
Was this helpful?
Thank you for voting!
Leaked, disassembly revealed it was the drive seal washer grommet. Drive block was also rusted out and frozen to the washer drum
3 of 3 people found this instruction helpful.
  • James from ARVADA, CO
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set
Disassembled lower part found nothing wrong.
Started disassembly from the top. Immediately ran into trouble not knowing exactly how the tub was anchored to the drive. Once I got down to the tube and drive block there was nothing I could do to go further. I guessed it was a press fit onto the drive, but there were many instructions and I couldn't be sure. Parts Select expanded drawing was the most useful tool; it was correct omitting a few details. Anyhow, cleaning out my garage I found one of my old gear pullers that I could ring to complete the disassembly. All the sudden I was in business, pulling the washer drum off the drive block and shaft, getting down to the leaky lower seal. A that point it was just a matter of cleaning everything up and buying all the rusted out parts to reassemble. I spent $150-200 on parts, but its completely rebuilt now and runs like a charm. Probably have around 20-50 hours all told, into the repair. Most of this was reading instructions, watching videos, and trying to figure out the rest (3). Doing the actual work spread over time until my wife and sons threatened to throw the thing out. Never. Once I decide I'm gonna do something, I do it. LOL!
Was this helpful?
Thank you for voting!
Shaking during spin cycle
3 of 3 people found this instruction helpful.
  • david from BREMO BLUFF, VA
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers
Followed the video. Removed the case and holder clips (not really needed) and replaced the springs. It did nothing to stop the problem and there are no more fixes.
Was this helpful?
Thank you for voting!
washer quit spinning
3 of 3 people found this instruction helpful.
  • Melody from ENTERPRISE, FL
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
Followed the video posted on the website. Everything went great - first repair attempt took about 45 minutes. Time consumed mostly due to the straps that hold the motor in place being very difficult to put back on and that the cabinet was a little difficult to replace due to the amount of rust around the bottom of it. Tried out the washer when done, and noticed a burning rubber smell. Took everything apart again, checked it, and everything seemed to be ok (made sure all four rubber feet were in place on the motor) so put it all back together again. Noticed the smell again so took it apart a third time, and when the motor felt pretty warm, decided to do an internet search for "burning rubber smell after replacing drive motor coupling." The answer popped right up - the replacement parts were not solid plastic like the original ones- they had metal on the inside of them, and needed to be tapped, a bit forcefully, with a hammer and socket until flush on the both the motor and transmission axles. Once the parts were flush, the straps that hold the motor in place snapped right on. Still a challenge with the rusted cabinet, but once all together again, worked perfect! Thanks to this site , I have fixed washers, dryers, and refrigerators and used them now nearly 20 years! I showed my daughter and granddaughter how to repair them and they don't hesitate to pitch in and help or handle the repairs on their own - again with much appreciation to this sitefor the accurate "how to" videos, the right parts, fast shipping, and great prices.
Was this helpful?
Thank you for voting!
Weak and broken springs on washing machine
3 of 4 people found this instruction helpful.
  • Monty from OXON HILL, MD
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Looked at the repair instructions on your web site and it made the repairs simple and easy.
Was this helpful?
Thank you for voting!
Washer tub goes out of balance in spin cycle.
3 of 4 people found this instruction helpful.
  • Dale from DOTHAN, AL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Found leveling spring loose on bottom of washer, the sheet metal on bottom of cabinet ad rusted through. Drilled new hole in sheet metal and installed new leveling spring. Greased hole with blue marine grease so it will last another 40 years.
Was this helpful?
Thank you for voting!
Water Pump leaked
3 of 4 people found this instruction helpful.
  • alan from american fork, UT
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
We unscrewed the two screws at the back of the control panel. Holding the control panel on both ends
we pulled it toward the front of the machine, slightly and gently lifting it at the same time, removing it from the metal surround. Holding the control panel up off of the surround we rocked the surround forward and lifted it off t he washing machine frame.
We could see where the leak was coming from. We took the hose clamps from the two ports, then
using a pair of pliers pulled the two clips that are holding the pump onto the shaft protruding from the
electric motor. We matched up the part on the web sight. Ordered the part then when it came in we just reversed the order putting the machine back together. The hardest and most time consuming
thing about this repair was the clean up of the washing machine. (Dirt and soap residue does
build up on the inside of the wash tubs.)
Was this helpful?
Thank you for voting!
rubber seal broke aprt
3 of 4 people found this instruction helpful.
  • Lisa from North Attleboro, MA
  • Really Easy
  • Less than 15 mins
slid the old seal off the lid and the new one popped on so easily
I do so many self- repairs at home now this was not even an issue.
Was this helpful?
Thank you for voting!
All Instructions for the 11020052994
91 - 105 of 1171