EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

11020052994 Kenmore Washer - Instructions

All Instructions for the 11020052994
76 - 90 of 1171

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washing machine making a grinding noise
4 of 4 people found this instruction helpful.
  • Tracy from Yuba City, CA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Purchased and installed PS1485646 COUPLING, MOTOR (Direct Drive Coupling). We googled "Washing Machine making a grinding noise. Several people suggested coupling probably broken. We located some instructions online regarding dis-assembly, sure enough,the coupling was broken. We ordered the part from Partselect.com. It arrived in three days, replaced the broken coupler. Washing machine back in business for around $20. Hooray! Thanks, Partselect!
Was this helpful?
Thank you for voting!
Tub not spinning or agitating, but could hear motor working.
4 of 4 people found this instruction helpful.
  • MICHAEL from CLEARWATER, FL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
Disconnected power, all hoses. Tilted washer backward to see underneath. (Placed sturdy 6" high object under back of washer to keep it from going flat on ground and possibly damaging hose connects). Looked for area where motor and transmission connect. Saw broken part (coupling). After trial and error, figured out how to remove pump and t hen motor, by removing strap type holding clips, and then broken part was accessible. Ordered part online and was easy to install and reassemble washer now that I knew how it came apart. If I had known the part name or number beforehand, I could have watched the replacement instruction video on this site, but I figured it out anyway, and I did it without removing the whole control switch panel and side panels/body of washer, like they do in the video. But..I guess they had to do that to give you a good view of all the parts and things they were removing underside. I recommend watching video for this part install,so you see what needs to be removed and how underneath, but then just tilting washer back to access underside, without all that control panel and sides removal.
Was this helpful?
Thank you for voting!
Washer excessive vibration during rinse spin
4 of 4 people found this instruction helpful.
  • John from ODESSA, TX
  • A Bit Difficult
  • More than 2 hours
  • Pliers, Screw drivers, Socket set
Well, after resolving Part Select (PS) shipping issues (PS sent me two refrigerator glass shelves instead of a Tub Spring); And as it turns out they sent me the wrong part for the suspension pads, which I have returned for credit. It takes 3-4 weeks to obtain your credit BTW.

Well after removing the cabinet, agitator, wash bask et, plastic tub, all 5 springs, & pump suction line, I was able to access the Tub wear pads and suspension pads. As it turns out the suspension pads looked good.
Thank God, as PS had sent wrong parts. I replaced the wear pads, the 5 springs, and reversed the disassembly process. Took about 6 hours.
But washer works fine now, still vibrates, but does not walk across floor any more.
Was this helpful?
Thank you for voting!
The washer would drain, but was screaming while doing nothing else.
4 of 4 people found this instruction helpful.
  • Richard from JAMESTOWN, PA
  • Really Easy
  • More than 2 hours
The tough part was replacing the front cabinet.
I did consult the video for help on replacing the clutch spring.
Thank you for that bit.

I admit to taking too much apart, most of the cabinet back can be left alone.
Some of the plastic wire keepers/routers suffered, as well as the console hinges.

The ne wly reassembled washer works without a hitch, and truely it took me about 4 hours over several days to dissamble and reassemble.
It is louder in the audible range than before, but very serviceale for another 20 years, saints willing.
Was this helpful?
Thank you for voting!
washer would not spin or agitate
6 of 10 people found this instruction helpful.
  • Doreen from Ashtabula, OH
  • Easy
  • 1- 2 hours
  • Screw drivers, Socket set, Wrench (Adjustable)
I first took the 2 screws out and disconnected the wires, I got my parts ordered and when they came in I put it back together then plugged th wires back in. I really could not believe that I could do something of this nature but when I started it was easy. My boyfriend wanted to take the washer to a repair shop, but I said first I will take a look and see if it will be worth saving. Otherwise I will junk it. It cost me with shipping costs 41.00 I am very proud of my self.
But I read other peoples experience on fixing the same problem that I had so I gave it a try.
I will not hesitate to do other jobs myself. Doreen Finlaw
Was this helpful?
Thank you for voting!
direct drive washing machine not spinning
4 of 5 people found this instruction helpful.
  • Hoang from Fairfax, VA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Direct drive, no belt. Motor sounds like it's spinning but the agitator is not. Bought the coupling (that goes between the motor and the transmission) and replaced it in less than 15 minutes. Two screws and two clips to open the cover. Two clips to move the water pump out of the way. Two screws and two clips to take out the motor. R eplace the coupling and reverse the steps.
Was this helpful?
Thank you for voting!
The lid seal cracked and came off causing vibration
4 of 5 people found this instruction helpful.
  • David from Brookhaven, PA
  • Really Easy
  • Less than 15 mins
Slid the replacement on the lid and it worked like a charm - no more vibration.
Was this helpful?
Thank you for voting!
Old seal fell a part and caused bad virbrations
4 of 5 people found this instruction helpful.
  • Michael from Tinley Park, IL
  • Really Easy
  • Less than 15 mins
Slid off the old and slid on the new part. Actually my wife did it with no help and was rather pleased with her self on not needing any help except ordering it.
Was this helpful?
Thank you for voting!
the washing machine would pump the water out, but the agitator would not spin, and it was making noise.
5 of 8 people found this instruction helpful.
  • mario from eastchester, NY
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
The video that was shown about how to perform the repair was spot on. I wasn't sure exactly what part I needed. I took the advise from you stating that these symptoms I described usually meant that the part I ordered was the correct repair In 65% of the cases. I was delighted to see that when I followed the instruction video, and the moto r was removed, there was my coupling, In several pieces. At that point I knew that I ordered the correct parts.
Thank You,
Mario for Eastchester, NY.
Was this helpful?
Thank you for voting!
Washer wouldn’t drain and spin
3 of 3 people found this instruction helpful.
  • Thomas from KENT, CT
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I re moved actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.
Was this helpful?
Thank you for voting!
Agitator top part not working, dog legs worn off
3 of 3 people found this instruction helpful.
  • terry from ORTING, WA
  • Very Easy
  • Less than 15 mins
  • Socket set
Took out old parts and put in news ones, super easy and works great!!
Was this helpful?
Thank you for voting!
The washer pumps but does not spin
3 of 3 people found this instruction helpful.
  • C. Scott from Fremont, NE
  • Really Easy
  • 15 - 30 mins
  • Socket set
I did a Google search for the model number and found this site, PartSelect.com. Based on the diagrams on the site and what I could see underneath the washer, it was clear that the motor coupling was now gone and the shattered pieces of it were all over the floor. So I ordered a new coupling and waited for it to arrive, it was shipped in j ust a few days. Once I had the new coupling all I had to do was remove a couple of brackets holding the pump onto the motor, and the motor onto the gearbox; unplug the electrical terminals and lift the motor out. There are two halves to the coupling, one sits on the shaft of the gearbox and the other on the shaft of the motor. Both of these are seated into a rubber boot that is also a part of the coupling. Once the motor is sitting on the gearbox with all the coupling parts seated in place, just plug everything back in and replace the brackets. You will need a 1/4 socket to remove/replace the motor brackets. Also, it should be noted that you will want to unhook everything that is hooked to the wall (hoses, power cord) but it assumed you've already done this if you have access the the underneath of the washer.
Was this helpful?
Thank you for voting!
Kenmore 80 Series Washer - Agitator Stopped Working
3 of 3 people found this instruction helpful.
  • Peter from WRENTHAM, MA
  • Easy
  • 15 - 30 mins
  • Socket set
First I screamed at the ceiling, because I have a three year old and an infant, and the washing machine was dead. Then I went to youtube. It seemed like the "agitator dogs" were the issue.

In this spirit of any repair, I replaced them, and it was not the issue. I don't know what I expected.

Ceiling. YouTube. Pacing .

Then I figured it was this part - the motor coupling. I unplugged the machine and took out the drain tube. I leaned the machine back and propped it up with an empty detergent bottle, because those were abundant. Ratchet off a few bolts and the motor comes out. The coupling was indeed broken. The new one slips right in - I tapped it a few times with a mallet for good measure / vengeance. Ratcheted the bolts back on and tipped it back up.

Pros: Washer works now.
Cons: Everest-esque laundry pile to address.

But hey, it worked! I am no handyman and it wasn't too bad at all. Half hour tops.
Was this helpful?
Thank you for voting!
Part was cracked and falling apart
4 of 6 people found this instruction helpful.
  • Joyce from Dallas, TX
  • Really Easy
  • Less than 15 mins
Too simple. The old one practicaly fell off and all I had to do was push the new one into place. It locked itself in and was ready to use.

No more rattling or noise when it runs now.
Was this helpful?
Thank you for voting!
pump did not pump water out
3 of 3 people found this instruction helpful.
  • Brian from HUMMELSTOWN, PA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Put new one on work good, but now can't pump no more .the problem now is the spin cycal broke and I not going to fix it. Thank for the part work good.
Was this helpful?
Thank you for voting!
All Instructions for the 11020052994
76 - 90 of 1171