My Orders
Estate Range Switches
GET YOUR OFFICIAL Estate PARTS TO ENSURE VICTORY
Popular Estate Range Switches
This surface burner element switch is for an 8-inch surface burner on an oven, stove, or range. The element switch controls the heat of the surface burner. Disconnect power to your range before completing this repair because you will be working closely with electrical circuits. Remove the screws from back panel and the console, and remove the console to expose the switch. It is recommended to check for overheating or arcing on the wiring harness in case they need to be replaced as well. The harness that connects to the switch features a slip-on terminal for easy installation.
This surface burner element switch is for an 8-inch surface burner on an oven, stove, or range. The element switch controls the heat of the surface burner. Disconnect power to your range before completing this repair because you will be working closely with electrical circuits. Remove the screws from back panel and the console, and remove the console to expose the switch. It is recommended to check for overheating or arcing on the wiring harness in case they need to be replaced as well. The harness that connects to the switch features a slip-on terminal for easy installation.
Installation Instructions
chaz from fairplay, CO
the element did not turn compleatly off, the on light stayed on.
removed the screws holding the back metal panel, this exposed the wires to the switch. tested the wires to find that they were live when the switch was in the off position. ordered a new switch. UNPLUGED THE STOVE. removed the knob on the front of the stove. this exposed 2 screws, removed screws and the switch came away from the stove. re
... Read more
moved each wire from the old switch and replaced them in the same position on the new switch. inserted new switch into the stove and attached the 2 screws. replaced back panel and pluged in stove. all tested well
Read less
This surface element control switch, also known as an infinite switch, is a genuine OEM replacement designed for 6-inch electric burners on select ranges. It regulates the power supplied to the surface element, allowing precise control over heat levels from low to high. Compatible with models from Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, and other associated brands, this dual-coil switch is a common solution for issues such as burners that fail to heat, remain stuck on high, or cannot adjust temperature properly. If the burner heats intermittently or not at all, replacing the switch may restore proper function. Always disconnect power or turn off the circuit breaker before installation. Sold individually.
This surface element control switch, also known as an infinite switch, is a genuine OEM replacement designed for 6-inch electric burners on select ranges. It regulates the power supplied to the surface element, allowing precise control over heat levels from low to high. Compatible with models from Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, and other associated brands, this dual-coil switch is a common solution for issues such as burners that fail to heat, remain stuck on high, or cannot adjust temperature properly. If the burner heats intermittently or not at all, replacing the switch may restore proper function. Always disconnect power or turn off the circuit breaker before installation. Sold individually.
Installation Instructions
Bruce from Pasadena, MD
The old switch broke off.
Removed two screws that held the unit in then pulled out a few inches so I could see where the 5 wires were. Then I replaced one at a time till done. then replaced the retaining screws.
This infinite control switch is designed to regulate the heat output of an 8-inch surface burner on electric ranges and cooktops. It allows precise control over temperature levels by adjusting the voltage sent to the heating element, ensuring consistent and responsive cooking performance. Compatible with a wide range of models, this component is a direct replacement for switches that fail to heat or maintain temperature. The switch operates by responding to user input via the control knob, delivering the appropriate voltage to the burner. Installation requires disconnecting the appliance from power and using standard tools. Safety precautions, including wearing protective gloves and consulting model-specific instructions, are recommended.
This infinite control switch is designed to regulate the heat output of an 8-inch surface burner on electric ranges and cooktops. It allows precise control over temperature levels by adjusting the voltage sent to the heating element, ensuring consistent and responsive cooking performance. Compatible with a wide range of models, this component is a direct replacement for switches that fail to heat or maintain temperature. The switch operates by responding to user input via the control knob, delivering the appropriate voltage to the burner. Installation requires disconnecting the appliance from power and using standard tools. Safety precautions, including wearing protective gloves and consulting model-specific instructions, are recommended.
Installation Instructions
RON from KAUFMAN, TX
The burner would keep heating after turning off the switch
Start by turning off the power to the range.
It was fairly easy to take the "Control Deck" off the top of the range by removing about 8 screws. I leaned the deck forward without removing any wires except a green ground that was held on by one of the screws.
There are two small screws under the switch knob holding the Infinite S ... Read more witch to the panel. I removed these and let the switch hang on the wires. To avoid missplacing or crossing the wires... I moved one wire at a time to the new switch, then attached the switch to the panel and put it all back together.
Whole job was done in about 15 minutes
It was fairly easy to take the "Control Deck" off the top of the range by removing about 8 screws. I leaned the deck forward without removing any wires except a green ground that was held on by one of the screws.
There are two small screws under the switch knob holding the Infinite S ... Read more witch to the panel. I removed these and let the switch hang on the wires. To avoid missplacing or crossing the wires... I moved one wire at a time to the new switch, then attached the switch to the panel and put it all back together.
Whole job was done in about 15 minutes
Read less
This part carries 5.2-6.6 amps.
This part carries 5.2-6.6 amps.
Installation Instructions
Mikhail from Iowa City, IA
One of the heat elements in my oven would not heat
1. Disconnected power from my oven.
2. Removed several screws that held the control block
3. Removed two screws that held the switch itself disconnected wires and removed switch
4. Reconnected all wires to new switch (no soldiering gun required)
5. Put control block back
Overall - very easy
2. Removed several screws that held the control block
3. Removed two screws that held the switch itself disconnected wires and removed switch
4. Reconnected all wires to new switch (no soldiering gun required)
5. Put control block back
Overall - very easy
This oven temperature switch is a 15-amp, 240-volt component designed to regulate cooking modes such as bake, broil, and convection in electric ranges. Also referred to as a heat selector switch, it allows users to control the oven’s heating functions by directing power to the appropriate element. A failing switch may result in symptoms such as no heat, insufficient heat, inconsistent temperatures, or an oven that won’t start. This replacement part restores proper temperature regulation and cooking performance. Note that this is the switch assembly only; the control knob is sold separately. Installation typically involves disconnecting power, accessing the control panel, and replacing the switch using existing wiring and mounting points.
This oven temperature switch is a 15-amp, 240-volt component designed to regulate cooking modes such as bake, broil, and convection in electric ranges. Also referred to as a heat selector switch, it allows users to control the oven’s heating functions by directing power to the appropriate element. A failing switch may result in symptoms such as no heat, insufficient heat, inconsistent temperatures, or an oven that won’t start. This replacement part restores proper temperature regulation and cooking performance. Note that this is the switch assembly only; the control knob is sold separately. Installation typically involves disconnecting power, accessing the control panel, and replacing the switch using existing wiring and mounting points.
What this part fixes:
- Element will not heat
- Little to no heat when baking
- Will Not Start
Installation Instructions
frank from pittsburg, TX
had for 2 weeks didnot work called for warinty they fixed stoped woking again about 18months later called them got price then bought though you.
first i turned off breaker . then slid out stove .usea cordless screwdriver totake off back then unplug switch then take off knob then take screwes out of front of switch theninstall new one revice method. took me longer to do this then to do the part
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This switch controls the stove top surface burner.
This switch controls the stove top surface burner.
Installation Instructions
Ron from GREELEY, CO
Broke off knob and burner switch accidentally
Lift top of control panel where florescent light bulb is enclosed. Remove florescent bulb. Remove two Phillips head screws that are below bulb. Top of control panel swings down toward front of range to allow access to burner switches. Simply replace wires on new switch in same location as old switch.
Introducing the Infinite Switch Surface Element Control Switch, a genuine OEM part that remarkably enhances the performance of your Whirlpool appliance. Praised for its dependable function, it operates to turn your surface element on and off, deftly controlling the heat it produces. This versatile part is designed for ranges and contributes to a rich cooking experience. Informational tip: before installation, ensure your range is unplugged or your house circuit breaker is off to ensure a safe and efficient setup. Do remember to wear work gloves for your protection during this procedure. Turn to this part to revitalize the operation of your Whirlpool range.
Introducing the Infinite Switch Surface Element Control Switch, a genuine OEM part that remarkably enhances the performance of your Whirlpool appliance. Praised for its dependable function, it operates to turn your surface element on and off, deftly controlling the heat it produces. This versatile part is designed for ranges and contributes to a rich cooking experience. Informational tip: before installation, ensure your range is unplugged or your house circuit breaker is off to ensure a safe and efficient setup. Do remember to wear work gloves for your protection during this procedure. Turn to this part to revitalize the operation of your Whirlpool range.
This part allows you to select the bake or broil function for your oven.
This part allows you to select the bake or broil function for your oven.
Installation Instructions
Richard from Mariposa, CA
Broken Switch
Made sure was off, Removed rear panel, removed 2 screws, removed wire clips from old switch, installed wires on new switch, installed switch with 2 screws, re-installed back panel, reconnected power and checked switch function. OK!
This part controls how much heat is produced and turns the burner on and off.
This part controls how much heat is produced and turns the burner on and off.
Installation Instructions
Thomas from CLEARWATER, FL
The simmer switches had failed in the simmer ON position and the 2 burners would not heat up higher than simmer
I pulled the range away from the wall enough to reach the back. There is a small access panel on the back of the control panel at the top of the range. It removes with 3 phillips head screws. Once removed, the back of the switch is accessible. Simply pinch the 2 snaps on the side of the switch and push it out through the front of the pane
... Read more
l. Remove the 3 wires from the failed switch and install them on the new switch. It isn't obvious which way the switch installs and I'm not sure it matters. But there is stamped writing on the switch that will help orient it. Then simply push the switch back in place until the snaps catch and install the access panel.
Read less
Used with the 6" (small) element.
Used with the 6" (small) element.