My Orders
Estate Range Valves
GET YOUR OFFICIAL Estate PARTS TO ENSURE VICTORY
Popular Estate Range Valves
The pilot stays lit all the time and, when the oven is turned on, the flame gets bigger and surrounds the thermocouple. When the thermocouple senses the required heat, the safety valve opens to let the gas flow to the oven burner tube where the pilot flame ignites the gas.
The pilot stays lit all the time and, when the oven is turned on, the flame gets bigger and surrounds the thermocouple. When the thermocouple senses the required heat, the safety valve opens to let the gas flow to the oven burner tube where the pilot flame ignites the gas.
What this part fixes:
- Gas igniter glows, but will not light
- Little to no heat when baking
- Will Not Start
Installation Instructions
Peter J from Brooklyn, NY
Pilot Light Won't Stay Lit
First I removed the oven door by pulling straight up off of the hinges in the open postion. Next remove oven racks,then use 1/4 nutdriver to remove back screws on inside oven bottom plate. Next remove gold nut on silver tube @ pilot connection,then remove 1/4 nuts that hold pilot assembly. Next open top of stove and remove small gold nu
... Read more
t "with the thin wire from pilot"attached to the back left of oven control knob. Snake that nut and wire from the top of the stove down to the oven and removethe whole pilot assembly. To install carefully unroll the new pilot assembly starting from the oven "there are two round holes you need to snake the tube into"and up behind the back & into the stove top. Make your connection@ the oven assembly. Next attach the assembly with the 1/4 screws that you removed,then make your connection"gold screw silver tube" now push in your oven control knob to alllow gas to flow to the pilot tube and check for leaks with a water @ soap solution. No bubbles no leaks. Light your pilot . . . . You must hold in the oven knob. Put back in oven plate,,,, 1/4 screws,,,,racks close the stove top ,put door back on hinges and your done. . . . . Hope I helped,. . Pete
Read less
Sold individually.
Sold individually.
Installation Instructions
George from CASTROVILLE, CA
parts missing on a used stove
put in place
This part makes sure that no gas is released until the igniter gets enough power to ignite the gas range.
This part makes sure that no gas is released until the igniter gets enough power to ignite the gas range.
This is the Right Rear Burner Head.
This is the Right Rear Burner Head.
Installation Instructions
Charles from ATLANTA, GA
REPLACING burner head and ignitor
Remove the screw on the front of each side, also there are two screws holding the burner controls. Remove the burner knobs. There are two screws holding the burner head to the top of the burner panel, looking down on the burner head, these will not come out easily. Here's where the drill comes in. Drill the two screws head off, there are
... Read more
two gas line connections that must be removed, be careful not to twist the gas line. Remove the burner head and replace with the new one. When replacing the burner head, screw the gas line to the burner head first, then to the main gas control.
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This electronic burner box forms the main housing that supports and holds the surface heating elements under an electric cooktop. It keeps the elements stable, level, and properly aligned so they heat evenly during cooking. This replacement is useful when the original housing becomes bent, corroded, or damaged, or when elements begin to sag, rattle, or sit unevenly. Measuring roughly 25 inches by 34 inches by 3 inches, it is designed to match the original fit, and installation typically involves removing the cooktop surface and transferring the elements into the new box to restore solid, reliable support.
This electronic burner box forms the main housing that supports and holds the surface heating elements under an electric cooktop. It keeps the elements stable, level, and properly aligned so they heat evenly during cooking. This replacement is useful when the original housing becomes bent, corroded, or damaged, or when elements begin to sag, rattle, or sit unevenly. Measuring roughly 25 inches by 34 inches by 3 inches, it is designed to match the original fit, and installation typically involves removing the cooktop surface and transferring the elements into the new box to restore solid, reliable support.
Sold individually.
Sold individually.
Installation Instructions
George from CASTROVILLE, CA
parts missing on a used stove
put in place
Sold individually.
Sold individually.
Installation Instructions
John from PRINCETON, IN
Oven would not maintain temperature and LR burner would not turn on
Oven temperature sensor was very easy to replace - just need a Philips screw driver.
Gas manifold valve for burner was a little awkward but not hard to do - I used pliers to undo because I didn't have a wrench to fit. It all went fine.
Gas manifold valve for burner was a little awkward but not hard to do - I used pliers to undo because I didn't have a wrench to fit. It all went fine.
This part distributes flame evenly to your cookware.
This part distributes flame evenly to your cookware.
Installation Instructions
Charles from ATLANTA, GA
REPLACING burner head and ignitor
Remove the screw on the front of each side, also there are two screws holding the burner controls. Remove the burner knobs. There are two screws holding the burner head to the top of the burner panel, looking down on the burner head, these will not come out easily. Here's where the drill comes in. Drill the two screws head off, there are
... Read more
two gas line connections that must be removed, be careful not to twist the gas line. Remove the burner head and replace with the new one. When replacing the burner head, screw the gas line to the burner head first, then to the main gas control.
Read less
Burner valves are attached to the main gas line. When the switch is turned the gas then flows into a tube that mixes with air, creating the appropriate mixture for combustion.
Burner valves are attached to the main gas line. When the switch is turned the gas then flows into a tube that mixes with air, creating the appropriate mixture for combustion.