Official Electrolux Dryer Parts | Order Today, Ships Today

Your Price

$61.99

ROLLER KIT

PartSelect Number PS12746506

Manufacturer Part Number 5304523155

This is a genuine replacement drum roller for a dryer. This part includes a roller which has an axle and two tri-rings. The dryer drum roller holds the drum in place while it rotates on the dryer support wheels. If rollers are worn out, the dryer will be noisy. This is a genuine OEM replacement part. If your dryer has more than one drum support roller, it is recommended to replace both at the same time to ensure proper rotation. They often wear at the same rate. You will need to remove the outer front panel to access this part. This replacement part is sold separately.

Fixes these symptoms

Noisy
See more...

Installation Instructions

Philip from Oakland, CA

Noisy Dryer

When I described the noise to a YouTube appliance diagnostician, I was directed to check the felt seals front and back of the rotating drum for wear, tears, or foreign objects. As it happens the felt seals looked find and there were foreign objects so, not wanting to disassemble and reassemble the dryer more than I had, I ended up replacing all the replaceable moving parts that I considered possible culprits: The idler tension spring, the idler tension bracket (which includes a nylon pulley wheel), the drum belt, the five rubber-tipped bearings that support the drum and keep it in place, and the foam seal on the blower housing which seemed a little brittle and old, as well as high-temperature adhesive for the latter. The instructional videos here and on YouTube were extremely helpful (I doubt that I would have attempted this job at all, had I not watched these ahead of time). The most time-consuming aspect was waiting for the arrival of the parts as I didn't order them all at the same time or all from the same place (I ordered from whomever could ship me a given part the fastest. Disassembly took less than an hour. Re-assembly with the new parts in place took about the same but was a little more awkward because this appliance sits in a very narrow closet and it's difficult to ensure that the 4" flexible duct stays in place when sliding the appliance back into the closet. No regrets. Now I know the basics if this dryer needs attention in future and I also know all the parts that I can eliminate as suspects in any future maintenance (the parts that I replaced) Read more...

Your Price

$55.96

Belt

★★★★★

(3)

PartSelect Number PS2349294

Manufacturer Part Number 134719300

Fixes these symptoms

Noisy
Will not tumble
See more...

Installation Instructions

Philip from Oakland, CA

Noisy Dryer

When I described the noise to a YouTube appliance diagnostician, I was directed to check the felt seals front and back of the rotating drum for wear, tears, or foreign objects. As it happens the felt seals looked find and there were foreign objects so, not wanting to disassemble and reassemble the dryer more than I had, I ended up replacing all the replaceable moving parts that I considered possible culprits: The idler tension spring, the idler tension bracket (which includes a nylon pulley wheel), the drum belt, the five rubber-tipped bearings that support the drum and keep it in place, and the foam seal on the blower housing which seemed a little brittle and old, as well as high-temperature adhesive for the latter. The instructional videos here and on YouTube were extremely helpful (I doubt that I would have attempted this job at all, had I not watched these ahead of time). The most time-consuming aspect was waiting for the arrival of the parts as I didn't order them all at the same time or all from the same place (I ordered from whomever could ship me a given part the fastest. Disassembly took less than an hour. Re-assembly with the new parts in place took about the same but was a little more awkward because this appliance sits in a very narrow closet and it's difficult to ensure that the 4" flexible duct stays in place when sliding the appliance back into the closet. No regrets. Now I know the basics if this dryer needs attention in future and I also know all the parts that I can eliminate as suspects in any future maintenance (the parts that I replaced) Read more...

Your Price

$76.76

Lint Filter

★★★★★

(21)

PartSelect Number PS2349312

Manufacturer Part Number 134793600

Located at the front of the washing machine, this dryer lint filter traps lint and debris from the exhaust air flowing out of the dryer drum. This part measures approximately 14 inches long x 11 inches high. It has a plastic frame and a mesh body to catch debris. If your filter needs cleaning, the dryer cycle will take longer due to a buildup or lint or fabric softener affecting the air flow through the filter. If there is a buildup, try scrubbing the filter with hot water and soap. But if the filter is damaged, worn, or torn, it should be replaced. Cleaning the lint filter before starting the drying cycle is a great way to ensure your dryer performs properly.

Fixes these symptoms

Takes too long to dry
See more...

Installation Instructions

Yvette from RUTHER GLEN, VA

Lint filter unusable due to age

Inserted lint filter into slot.
Replacement is exact match to original filter. Read more...

High Limit Thermostat – Part Number: 3204267

Your Price

$85.96

High Limit Thermostat

★★★★★

(2)

PartSelect Number PS446428

Manufacturer Part Number 3204267

This high limit thermostat is used in a dryer and monitors the temperature to make sure it does not exceed 260 degrees Fahrenheit. When your dryer temperature reaches 260 it will cut it out and only comes back when it drops by at least 70 degrees Fahrenheit. If your dryer is overheating, taking too long to dry clothes, or is not producing enough heat, replacing the thermostat could be the solution to your problem. The tools needed for this part are a Phillips screwdriver, putty knife, and needle nose pliers. Refer to the manual provided by the manufacturer for installation instructions and guidance.

Fixes these symptoms

No heat or not enough heat
Shuts off too soon
Takes too long to dry
See more...

Installation Instructions

MELISSA from OKEECHOBEE, FL

dryer does not get very hot, takes two cycle's to dry

removed the screws, disconnected the wires. installed the new elements replaced the wires. Read more...

M Series Ignition Coil Kit – Part Number: 5303931775

Your Price

$35.04

M Series Ignition Coil Kit

★★★★★

(24)

PartSelect Number PS470049

Manufacturer Part Number 5303931775

This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes dryer. Some of the symptoms that this kit could be a solution for are: If there is no heat, not enough heat, or clothes takes too long to dry. In this case, the gas valve coils can be defective and replacing this part will help. Customers rate this project as easy. Refer to the installation diagram for further instructions. For safety, unplug your dryer before repair.

Fixes these symptoms

No heat or not enough heat
Takes too long to dry
See more...

Installation Instructions

Brett from Monticello, MN

Dryer would heat initially then cool down

The top of the dryer was easily removed by prying the front up with a screwdriver then tipping it back and off of the mounting brackets. Then the front of the dryer was removed by unscrewing a single screw on each side that held the front to the side panels then pulling the front away from the dryer. Once the front was off, the coils were easily accessible on the bottom left side. A metal bracket held the coils on and was somewhat tough to get the two screws removed on it as they were stuck, but once they were removed the coils easily came out and I was able to replace them in minutes. The whole job took 15-20 minutes and I now have a dryer that heats through the entire drying cycle. Read more...

Your Price

$33.02

Thermal Fuse

★★★★★

(3)

PartSelect Number PS4704883

Manufacturer Part Number 134711401

Fixes these symptoms

No heat or not enough heat
Will Not Start
See more...

Moisture Sensor – Part Number: 134786100

Your Price

$69.95

Moisture Sensor

★★★★★

(2)

PartSelect Number PS2349303

Manufacturer Part Number 134786100

Fixes these symptoms

Takes too long to dry
See more...

Installation Instructions

Stacey from TWO RIVERS, WI

The clip broke off our sensor making it disconnect, thus we had in inoperable 'new' machine.

By undoing the single screw which holds the sensor in place, the old one falls off. To replace: simply pop the two wires on their connections (small metal studs on the back), slide clip/wire end of sensor in place and replace the screw. You are back in business! Very simple repair that a DIY can save a ton! Read more...

Dryer Heater Element – Part Number: 134792700

Your Price

$197.53

Dryer Heater Element

★★★★★

(11)

PartSelect Number PS2349309

Manufacturer Part Number 134792700

This part is a heater, but may also be known as a heating element, and it is meant for your dryer. This is where the heat is generated during your machine cycle in order to properly dry your clothing. This model is a 5500 watt, and has three coils. If your heater is broken, that usually means there is a break in the coil element.If you are having trouble drying your clothes, you may want to check for a thermal cut out or a blown thermal fuse. For this repair you will need a number two square bit, a Phillips screwdriver, and a flat-head screwdriver.

Fixes these symptoms

No heat or not enough heat
Shuts off too soon
Takes too long to dry
See more...

Installation Instructions

Steven from MARIETTA, GA

Dryer wasn't heating properly, drying took too long.

Removed back of dryer with electric nut driver. Lots of screws. Removed old heating element to better access wires and thermostats. Removed baffle at end and transferred to new heater element. Transferred thermostats to new element, reconnected wiring in correct order. Installed new heater element in correct position using tab to locate. Replaced back of dryer. Reconnected dryer vent. Toughest part was squeezing out of space after reconnecting dryer vent. Unfortunately, too short for my weight. Read more...

Your Price

$17.06

Drum Belt

★★★★★

(53)

PartSelect Number PS1148434

Manufacturer Part Number 134503600

This drum belt, often referred to as a drive belt, is used in the assembly of dryers. It goes around the drum, the idler pulley, and the motor pulley. As the armature on the motor spins, this belt is what rotates the drum and tumbles your clothes during the dry cycle. If you can hear the motor running but the drum is not moving, that is a sign your belt is broken, stretched, or damaged, and can no longer grip the drum. This belt is 88 3/4 inches long, and is 1/4 inch wide. Because it is made of rubber it is common for this part to become brittle and need to be replaced. This is an authentic OEM replacement part, and it is sold individually. Remember to unplug your dryer before you begin this repair.

Fixes these symptoms

Marks left on clothes
No heat or not enough heat
Noisy
See more...

Installation Instructions

Cynthia from Lexington, SC

Squealing noise

We followed the instructions for the drum glide replacement and changed the belt and drum support bearing piece, cleaned it out too. Works like a charm. Thanks for saving us a bundle. Read more...