Dishwasher Motors

Popular Dishwasher Motors

Your Price
$109.32
  In Stock
Dishwasher Motor
★★★★★
★★★★★
21 Reviews
PartSelect Number PS5136127
Manufacturer Part Number W10537869
Also know as a diverter valve. This diverter motor is for dishwashers. Diverter motor controls the flow of water to the spray arms. Unplug the dishwasher and shut off the water supply before installing this part. Wear work gloves to protect your hands.
Fixes these symptoms
  • Leaking
  • Not cleaning dishes properly
  • Will Not Start
  • See more...
Installation Instructions
Dennis from PORTAGE, MI
Diverter valve was leaking.
After shutting off electricity, lay dishwasher on it's side (use a towel to absorb any water) then just use nut driver to remove faulty valve. Read more...
Your Price
$163.71
  In Stock
Dishwasher Pump Motor Kit
★★★★★
★★★★★
11 Reviews
PartSelect Number PS3497737
Manufacturer Part Number 154844301
This kit includes the motor and o-rings.
Fixes these symptoms
  • Leaking
  • Noisy
  • Not cleaning dishes properly
  • See more...
Installation Instructions
Jeff from Lancaster, PA
not cleaning, spray arms not working
The hardest part was disconnecting the dishwasher. the motor is located on the bottom so after pulling it out and laying it down on the front of the machine the motor unplugs and 2 screws hold it in place.The new motor comes with "O" rings so I applied a little grease and put it back together. 2 minutes to replace motor, 15 minutes to disconnect water and electric, 15 to reconnect. Read more...
Your Price
$40.39
  In Stock
Dishwasher Diverter Motor - 120V 60Hz
★★★★★
★★★★★
6 Reviews
PartSelect Number PS3579323
Manufacturer Part Number 4681ED3001D
This diverter motor, or stepper motor, controls the movement of the spray arms in your dishwasher. It directs water between the drain pump and the spray arms by turning a check valve inside the pump, managing the flow of water to these spray arms. This diverter motor runs on 120 volts and 60 Hz. When this motor fails, the dishwasher will not wash or drain properly. Please keep in mind that this genuine OEM replacement part is sold separately from the spray arms.
Fixes these symptoms
Installation Instructions
Glen from LINESVILLE, PA
Dishwasher gave the Ne code
When I turned the dishwasher over I discovered the PS3579323 diverter motor had failed due to a leak around the PS3536016 valve, check. No use replacing the diverter motor without fixing the leak so I turned the machine back over and disassembled the spray arms and top of the pump cover which reveled the case assy and the valve, check. Upon removal of the valve, check I discovered hair wrapped around it which compromised the MO31 packing and caused the leak. I probably could have just cleaned out the hair and reassembled it but because my installation is a bit of a pain I elected to change the case assy (because of a slight depression where the packing sets) the M031 packing, the MO25 valve, check, and the MO35 pump gasket. After that was accomplished I turned the machine upside down and replaced the MO26 diverter motor and reinstalled the dishwasher. End result: Ne code cleared, no leaks and now the dishes are clean on the top shelf and the wife is happy. There are great instruction videos on YouTube. Good luck! Read more...
Your Price
$182.70
  In Stock
Dishwasher Motor and Pump Assembly
PartSelect Number PS12712308
Manufacturer Part Number 5304519906
Fixes these symptoms
Your Price
$227.60
  In Stock
Dishwasher Pump and Motor Assembly
PartSelect Number PS11770231
Manufacturer Part Number W11025157
This pump and motor assembly is for dishwashers. Pump and motor assembly pumps water through the spray arms during the dishwashing cycle. Shut off the house circuit breaker for the dishwasher before installing this part. Wear work gloves to protect your hands.
Fixes these symptoms
Installation Instructions
Lana from PERRY, FL
The dishwasher would not spray water. It would pump water out and fill just not spray.
I followed the instructions on the Whirlpool site for my model and part (pump and motor assembly). It was a bit hard to get the original assembly out of the dishwasher. They make it look easy but if you look at the dishwasher they are using you will realize that it is brand new. So everything comes apart and goes together smoothly for them. That is not how it happens in reality. I am a woman of average size and had never done any kind of repairs to a dishwasher before. So, it was not easy. I was however able to get it apart and put back together. And now it works!! Read more...
Your Price
$85.30
  In Stock
Dishwasher Drain Pump
★★★★★
★★★★★
8 Reviews
PartSelect Number PS1765174
Manufacturer Part Number 154580301
The pump ejects the water from the unit.
Fixes these symptoms
Installation Instructions
Phillip Foster from Cleveland, OH
Dish washer would not drain
Repair was easy I removed the old drain pump by removing 1 clips with pliar & 1 band with a screw driver and replace the drain pump with the new one, I replace clip and the band. replace drain hose tighten down the band. I had to adjust the drain pump because it seem to be a little loud then the one I had to replace , now it works ! Read more...
Your Price
$89.33
  In Stock
Dishwasher Diverter Motor with Wire Harness
★★★★★
★★★★★
1 Review
PartSelect Number PS2328555
Manufacturer Part Number W10155344
NOTE: This part has been updated by the manufacture and the shaft seal is now incorporated into the sump housing. The seal for diverter motor shaft only available with the pump sump housing.
Fixes these symptoms
Installation Instructions
John from Springfield, OH
Water leaking underneath dishwasher
The leak was dripping from the diverter motor. After removing dishwasher the diverter motor was found to be corroded. The shaft grommet looked good. A new diverter motor was installed and dishwasher connected. After running it awhile the leak reappeared. It seemed the only possible thing left was the shaft grommet. Of course the grommet comes as part of the belly assembly. After searching for a better and cheaper solution I ordered a Whirlpool WPW10195677 grommet and it solved the leak. Read more...
Your Price
$179.58
  In Stock
Dishwasher Circulation Motor & Pump Kit with Harness
★★★★★
★★★★★
3 Reviews
PartSelect Number PS3501031
Manufacturer Part Number 154859101
This part has been redesigned by the manufacturer and may appear different, but will function the same. This kit helps propel the water through the spray arms.
Fixes these symptoms
  • Leaking
  • Noisy
  • Not cleaning dishes properly
  • See more...
Installation Instructions
Kurt from Corrales, NM
The dishwasher would not spray to middle or top rack and detergent would not dissolve.
I pulled off the cover inside the sump area. Then pulled the washer out from the counter and turned it on it's side. I took the old pump out and crimped a new wire harness on. It was a simple repair for a DIYer.

Before pushing the dishwasher back, I tested the dishwasher with it pulled out from the counter. It was easy to see water was flowing forcefully through the upper tubing now. Success.

Troubleshooting this faulty pump was harder because it was functioning, but it did not have enough force to push the water up to the top rack. I convinced myself that the pump was the problem by plugging the lower rack with a cork. The spray was still too weak to rotate the upper spray arm. I also ruled out the timer with a stop watch. This unit alternates upper and lower racks by pausing either 0.6 seconds or 3 seconds. This controlls a ball that diverts water to the upper or lower rack.
Read more...
Your Price
$238.72
  In Stock
Dishwasher Motor and Drain Pump
★★★★★
★★★★★
13 Reviews
PartSelect Number PS1766031
Manufacturer Part Number WH23X10028
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This pump has sound isolation mounting washers and a filter.
Fixes these symptoms
Installation Instructions
Trent from Shreveport, LA
Washing machine would cease functioning at the spin cycle and would not drain.
Remove the front coverfrom the machine. This is done by removing the 3 screws at the bottom of the panel. The panel then drops down and pulls straight off. The pump is located on the front right wall of the of the machine. You will notice a 2-3 inch diamete threaded cap on the right side of the front wall of the machine. This is the front of the pump and access to the filter. Place a large bucket under this cap and slowly loosen the cap. All of the water remaining in the machine will begin to drain (this could be a lot of water. Do not remove the cap completely so that you can quickly stop the flow of water if needed). Once all water is drained from the appliance, Disconnect the two hoses from the pump using a pair of pliers to looses the presure clamps, sliding the clamps back an then pulling off the hoses (be careful of any remaining water in the hoses). Then remove the two screws from the rear base of the pump that secure it to the bottom floor panel of the washer. Slide the pump slightly to the rear to free it from the fittings on the front wall of the machine and the lift the pump up. At this point, firmly pull out the wiring harness plugged into the top right side of the pump. Install the new pump by plugging in the wiring harness and resecuring the pump. Plug in the machine and run on the rinse and spin cycle to test. Read more...
Your Price
$207.38
  In Stock
Dishwasher Circulation Pump and Motor Assembly
★★★★★
★★★★★
10 Reviews
PartSelect Number PS11699805
Manufacturer Part Number W10782773
*** This part no longer includes the Chopper Assembly as per the Manufacturer *** The part functions by spinning the impeller of the circulation pump, which is used to move the water through the spray arms during the wash cycle.
Fixes these symptoms
  • Leaking
  • Noisy
  • Not cleaning dishes properly
  • See more...
Installation Instructions
Geoffrey from Indianapolis, IN
Dishwasher was not cleaning dishes.
SAFTY: Turn water off. Flip the circuit breaker.
PREPARE FOR REMOVAL: Unscrew / Remove kickplate. Disconnected water connect just behind the kickplate. Be ready with a couple of dishtowels. Pull the door down and remove any screws that go into the under part of your counter top. Jack the front legs screw down.
REMOVE: Gently pull the Dishwasher from under counter. Push the insulation flat against the side of the dishwasher about every six inches that you pull the dishwasher out to prevent it from snaggin on the cabinet face edges. Remove the baskets and spray arms. Careful not to damage the heating element.
NOTE: Here I noticed that the guy who installed the dishwasher kinked the copper line limiting the water into to my dishwasher. So my circulation pump/motor was probably running dry. I replaced with a flex type "dishwasher" hose that will easily coil up behind / underneath without kinking when I push back in. DO THE REPAIR RIGHT - DO IT YOURSELF!
REPAIR: I gently laid the dishwasher on it's side (cardboard underneath). I disconnected the power - 2 wires. Then, I only disconnect one wire harness, the sump tubing and the I thought I'd better remove the impeller that the sump tubing was connected to (it was only attached with one screw). Remove the 3 plastic clips around the pump/motor. Carefully push the pump into the dishwasher. DO NOT LET THE PUMP FALL AS IT MAY DAMAGE THE HEATING ELEMENT IN THE DISHWASHER! Push the new pump/motor in place until the seal is at least flush with the bottom. I used the back of a wood spoon. Don't pull on any part of the motor from the bottom or you'll break the thin aluminum casting. Just inserting the plastic clips back in place will pull the seal flush with the bottom again.

I was lucky. I simply removed the motor/pump, replaced it with the new motor/pump, and put everything back together in reverse. I put a little bit of silicone grease on the o-ring of the temperature probe. I happened to have some silicone grease because I also have a pool.
Done. It cost me $220 Vs. $550 quoted by Sears. That doesn't count the extra Sears would have charged my for repairing the kinked copper line. And you know they would've kinked it again. That only cost me $20 more and the flexible line couldn't have been easier to install. I could have done the whole thing for less but I opted to replace the pump/ motor together.
Getting it all done right, no leaks, no kinked line, keeping the dishwasher that matches the other appliances (VS. replacing it at $550 repair price), all less than 1/2 the price of a quoted repair - PRICELESS. - THANK YOU PART SELECT. DISCLAIMER: I have no affiliation with Part Select.
Read more...

Dishwasher Motor Brands