Trash Compactor Switches
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Trash Compactor Switches
Your Price
$64.14
In Stock
Trash Compactor Directional Switch
I took out the four screws that kept the top cover in place to expose the ram.
The gear shafts were turning but the ram would not lower, at first I though the ram drive bolts were stripped and it wouldn't engage the shaft. Then I realized there was a mechanical directional\limit switch at the top that controlled the power and direction the gear shafts were turning, this switch was broken.
Just had to take off the front plate that was held on by a number of screws and replace the switch that was held on by two more screws. It had five wires attached to it, the new switch was clearly labeled as to which color wire went where. Read more...
PartSelect Number PS11744742
Manufacturer Part Number WP777811
The function of the directional switch on your trash compactor is to ensure the ram lowers to compress your trash, then returns to the top position. If your trash compactor does not complete this task, will not stop at the end of the compacting cycle, or is noisy during operation, you may need to replace the directional switch. Be sure to disconnect your trash compactor from the power source before completing this repair. This is a fairly easy repair. After you open the control panel of the compactor, all you will need to do is unplug the old switch from the electrical wires, and plug the new switch in.
Fixes these symptoms
- Compactor ram gets stuck
- Doesn’t stop at end of compacting cycle
- Noisy
- See more...
Installation Instructions
Scott from Indianapolis, IN
Trash Compactor ram wouldn't lower
I pulled the trash compactor out from under the counter.I took out the four screws that kept the top cover in place to expose the ram.
The gear shafts were turning but the ram would not lower, at first I though the ram drive bolts were stripped and it wouldn't engage the shaft. Then I realized there was a mechanical directional\limit switch at the top that controlled the power and direction the gear shafts were turning, this switch was broken.
Just had to take off the front plate that was held on by a number of screws and replace the switch that was held on by two more screws. It had five wires attached to it, the new switch was clearly labeled as to which color wire went where. Read more...
Your Price
$153.92
In Stock
Trash Compactor Rotary Switch Kit
PartSelect Number PS382679
Manufacturer Part Number 675382
The rotary switch kit is also known as the start switch or the on and off switch, and is used to power on your trash compactor. The function of the rotary switch kit is to control the electrical power that is going into your trash compactor. This process happens when the switch sendsvoltage to the motor to start the compacting cycle. If your switch is broken the trash compactor will not start. A multimeter test can be performed to test the switch for continuity. The rotary switch kit will come with an on and off rotary switch, and two chrome knobs.
Fixes these symptoms
- Doesn’t stop at end of compacting cycle
- Won’t start
- Won’t stay on
- See more...
Installation Instructions
Edward from Deerfield Beach, FL
Change out defective switch
Pulled out compactor drawer and removed same, slid the compactor cabinet out and unpluged the appliance. Removed the two phillips head screws to release the control panel. lossened the locking nut from switch. matched the switches to be sure parts were the same,switched the wires to the new switch and reinstalled.replaced phillips screws, all Done !!!
Read more...
Your Price
$34.20
In Stock
Trash Compactor Light Switch
Thank you Read more...
PartSelect Number PS11742478
Manufacturer Part Number WP4387911
The light switch terminal is used in refrigerators and freezers to allow you to see inside your appliance by turning on when the fridge door is open and turning off when the door is closed. This part is 1.12 inches in length, 1 inches in width, and 1.75 inches in height. It weighs 0.026 pounds. If your light switch terminal is damaged or the light does not turn on when fridge door is open, replacing the light switch terminal can fix the problem. As a safety precaution, remember to unplug your fridge from the power source before beginning this installation. Refer to the manual provided by the manufacturer for further installation instructions and a detailed guide.
Fixes these symptoms
- Light not working
- See more...
Installation Instructions
Darlene from Holland, MI
Light switch broke on refridgerator door.
I measured the part then looked for a similar switch that might work. I was so happy to find the exact part we needed for our 24 year old refridgerator!! I was so impressed with your slection of parts and best of all I had the part in 2 days! You are in my "favorites" just in case I need you again!Thank you Read more...
Your Price
$99.27
In Stock
Trash Compactor Off-Switch Actuator Kit
PartSelect Number PS3489806
Manufacturer Part Number W10342596
This kit contains everything you will need to replace your faulty off-switch actuator, including: normally closed switch, toe guard, template, 2 screws, and actuator. If your trash compactor keeps running after the cycle is complete, you may have a defective off-switch. The off-switch is used to supply power to the motor to initiate the compaction cycle. Check to see if the off switch has been damaged, and that it is working properly. However, if the switch is damaged, or will not stop the cycle when the button is engaged, the off-switch will need to be replaced.
NOTE: This part has been redesigned by the manufacturer, but will still function the same as the original part.
Fixes these symptoms
- Doesn’t stop at end of compacting cycle
- Won’t start
- See more...
Installation Instructions
Scott from Ventura, CA
Beware the "two screws, five minutes" repair stories!
Needed a replacement actuator for KitchenAid trash compactor model KUCS03FTSS0. The part that broke is a small metal flange held in place by two screws. PartSelect.com clearly shows this part in the online exploded view of Container Parts. When I received the replacement order in the mail, I was surprised that it was not what I thought I had ordered (a single replacement piece), but a new, *completely redesigned* actuator kit. For this model (and perhaps for other models) this new kit requires much more extensive work than just replacing two screws. Repair entailed removing the trash compactor from its installation position, removing the recess cover and machine front, disconnecting and removing the old actuator switch, drilling holes in the machine front, attaching the new actuator assembly, and disconnecting and reattaching the foot pedal. Not an overly burdensome or complicated repair, but I had been fooled by the expectation of it being a five-minute job! (Submitted on 7/2/2011 by Scott - Ventura, CA)
Read more...
Your Price
$78.35
In Stock
Trash Compactor SWITCH-OFF
Replaced the drawer switch in the lower back (broken)
Replaced the top up/down switch (old and faulty)
Replaced the nylon ram nuts.
Replaced the control panel on/off/start switch.
Replaced the chain, and chain gear set.
Replaced the motor.
Replaced both sets of drawer rollers.
Final cost in parts - $450 - new compactor $1100. Works like new.
Had to be creative in the 2 drawer switch as they are now longer offered for sale. Found suitable replacements.
This may be my last chance at repairing this. Read more...
PartSelect Number PS11750906
Manufacturer Part Number WPW10242556
Installation Instructions
billy from HOUSTON, TX
My compactor is over 35 years old. Needed rebuild. Noisy. Quick cycle. Overload.
Replaced the bearing assembly at the base of both ram screws (worn out and noisy)Replaced the drawer switch in the lower back (broken)
Replaced the top up/down switch (old and faulty)
Replaced the nylon ram nuts.
Replaced the control panel on/off/start switch.
Replaced the chain, and chain gear set.
Replaced the motor.
Replaced both sets of drawer rollers.
Final cost in parts - $450 - new compactor $1100. Works like new.
Had to be creative in the 2 drawer switch as they are now longer offered for sale. Found suitable replacements.
This may be my last chance at repairing this. Read more...
Your Price
$48.55
In Stock
Trash Compactor Safety Switch
PartSelect Number PS405439
Manufacturer Part Number 9871829
Fixes these symptoms
- Won’t start
- See more...
Your Price
$72.51
In Stock
Trash Compactor Rocker Switch - Black
PartSelect Number PS11742364
Manufacturer Part Number WP4314961
This rocker switch can be used for both the oven selector and/or the oven light.
Your Price
$246.86
On Order
Trash Compactor On/Off/Start Switch
removed the faceplate (2 screws)
removed the switch assembley (2 screws)
took wires off old switch, and placed on the new.
replaced all the screws
Bingo, works great.
Saved $150 labor and service call. Read more...
PartSelect Number PS11731350
Manufacturer Part Number W10856868
This part activates your trash compactor.
Installation Instructions
Gerald from Vermilion, OH
on-off buttons not functioning
ordered the part from part select and received in 3 days.removed the faceplate (2 screws)
removed the switch assembley (2 screws)
took wires off old switch, and placed on the new.
replaced all the screws
Bingo, works great.
Saved $150 labor and service call. Read more...
Your Price
$89.80
In Stock
Trash Compactor Switch, Rotary Start-Run
PartSelect Number PS11747583
Manufacturer Part Number WP9871971
Your Price
$90.70
In Stock
Trash Compactor Rocker Switch - Black
Disconnected three wires to rocker switch noting position.(each wire is a different color and is an insulated blade connector. Pull off...push back on.
Compressed barbs holding old switch in place and removed switch.
Pressed in new switch until it popped into locked position. Reconnected wires.
Reattached front panel. Read more...
PartSelect Number PS11747588
Manufacturer Part Number WP9872161
All other colors have been discontinued, black is only available.
Installation Instructions
William from Fairview, NC
Compactor ram would not automatically return to starting position
Removed two screws holding front panel.Disconnected three wires to rocker switch noting position.(each wire is a different color and is an insulated blade connector. Pull off...push back on.
Compressed barbs holding old switch in place and removed switch.
Pressed in new switch until it popped into locked position. Reconnected wires.
Reattached front panel. Read more...
