My Orders
KitchenAid Trash Compactor Switches
GET YOUR OFFICIAL KitchenAid PARTS TO ENSURE VICTORY
Shop By Part Type
View MorePopular KitchenAid Trash Compactor Switches
This top limit and direction switch controls power to the trash compactor motor, it stops the motor when the ram reaches the top, a bad switch may cause the ram to get stuck, keep the motor running, or stop the compactor from starting, unplug the compactor before repair, check the model number before ordering
This top limit and direction switch controls power to the trash compactor motor, it stops the motor when the ram reaches the top, a bad switch may cause the ram to get stuck, keep the motor running, or stop the compactor from starting, unplug the compactor before repair, check the model number before ordering
What this part fixes:
- Compactor ram gets stuck
- Doesn’t stop at end of compacting cycle
- Noisy
Installation Instructions
Scott from Indianapolis, IN
Trash Compactor ram wouldn't lower
I pulled the trash compactor out from under the counter.
I took out the four screws that kept the top cover in place to expose the ram.
The gear shafts were turning but the ram would not lower, at first I though the ram drive bolts were stripped and it wouldn't engage the shaft. Then I realized there was a mechanical ... Read more directional\limit switch at the top that controlled the power and direction the gear shafts were turning, this switch was broken.
Just had to take off the front plate that was held on by a number of screws and replace the switch that was held on by two more screws. It had five wires attached to it, the new switch was clearly labeled as to which color wire went where.
I took out the four screws that kept the top cover in place to expose the ram.
The gear shafts were turning but the ram would not lower, at first I though the ram drive bolts were stripped and it wouldn't engage the shaft. Then I realized there was a mechanical ... Read more directional\limit switch at the top that controlled the power and direction the gear shafts were turning, this switch was broken.
Just had to take off the front plate that was held on by a number of screws and replace the switch that was held on by two more screws. It had five wires attached to it, the new switch was clearly labeled as to which color wire went where.
Read less
The rotary switch kit is also known as the start switch or the on and off switch, and is used to power on your trash compactor. The function of the rotary switch kit is to control the electrical power that is going into your trash compactor. This process happens when the switch sendsvoltage to the motor to start the compacting cycle. If your switch is broken the trash compactor will not start. A multimeter test can be performed to test the switch for continuity. The rotary switch kit will come with an on and off rotary switch, and two chrome knobs.
The rotary switch kit is also known as the start switch or the on and off switch, and is used to power on your trash compactor. The function of the rotary switch kit is to control the electrical power that is going into your trash compactor. This process happens when the switch sendsvoltage to the motor to start the compacting cycle. If your switch is broken the trash compactor will not start. A multimeter test can be performed to test the switch for continuity. The rotary switch kit will come with an on and off rotary switch, and two chrome knobs.
Installation Instructions
Edward from Deerfield Beach, FL
Change out defective switch
Pulled out compactor drawer and removed same, slid the compactor cabinet out and unpluged the appliance. Removed the two phillips head screws to release the control panel. lossened the locking nut from switch. matched the switches to be sure parts were the same,switched the wires to the new switch and reinstalled.replaced phillips screws,
... Read more
all Done !!!
Read less
This kit contains everything you will need to replace your faulty off-switch actuator, including: normally closed switch, toe guard, template, 2 screws, and actuator. If your trash compactor keeps running after the cycle is complete, you may have a defective off-switch. The off-switch is used to supply power to the motor to initiate the compaction cycle. Check to see if the off switch has been damaged, and that it is working properly. However, if the switch is damaged, or will not stop the cycle when the button is engaged, the off-switch will need to be replaced.
NOTE: This part has been redesigned by the manufacturer, but will still function the same as the original part.
This kit contains everything you will need to replace your faulty off-switch actuator, including: normally closed switch, toe guard, template, 2 screws, and actuator. If your trash compactor keeps running after the cycle is complete, you may have a defective off-switch. The off-switch is used to supply power to the motor to initiate the compaction cycle. Check to see if the off switch has been damaged, and that it is working properly. However, if the switch is damaged, or will not stop the cycle when the button is engaged, the off-switch will need to be replaced.
NOTE: This part has been redesigned by the manufacturer, but will still function the same as the original part.
Installation Instructions
Scott from Ventura, CA
Beware the "two screws, five minutes" repair stories!
Needed a replacement actuator for KitchenAid trash compactor model KUCS03FTSS0. The part that broke is a small metal flange held in place by two screws. PartSelect.com clearly shows this part in the online exploded view of Container Parts. When I received the replacement order in the mail, I was surprised that it was not what I thought
... Read more
I had ordered (a single replacement piece), but a new, *completely redesigned* actuator kit. For this model (and perhaps for other models) this new kit requires much more extensive work than just replacing two screws. Repair entailed removing the trash compactor from its installation position, removing the recess cover and machine front, disconnecting and removing the old actuator switch, drilling holes in the machine front, attaching the new actuator assembly, and disconnecting and reattaching the foot pedal. Not an overly burdensome or complicated repair, but I had been fooled by the expectation of it being a five-minute job! (Submitted on 7/2/2011 by Scott - Ventura, CA)
Read less
The light switch terminal is used in refrigerators and freezers to allow you to see inside your appliance by turning on when the fridge door is open and turning off when the door is closed. This part is 1.12 inches in length, 1 inches in width, and 1.75 inches in height. It weighs 0.026 pounds. If your light switch terminal is damaged or the light does not turn on when fridge door is open, replacing the light switch terminal can fix the problem. As a safety precaution, remember to unplug your fridge from the power source before beginning this installation. Refer to the manual provided by the manufacturer for further installation instructions and a detailed guide.
The light switch terminal is used in refrigerators and freezers to allow you to see inside your appliance by turning on when the fridge door is open and turning off when the door is closed. This part is 1.12 inches in length, 1 inches in width, and 1.75 inches in height. It weighs 0.026 pounds. If your light switch terminal is damaged or the light does not turn on when fridge door is open, replacing the light switch terminal can fix the problem. As a safety precaution, remember to unplug your fridge from the power source before beginning this installation. Refer to the manual provided by the manufacturer for further installation instructions and a detailed guide.
Installation Instructions
Darlene from Holland, MI
Light switch broke on refridgerator door.
I measured the part then looked for a similar switch that might work. I was so happy to find the exact part we needed for our 24 year old refridgerator!! I was so impressed with your slection of parts and best of all I had the part in 2 days! You are in my "favorites" just in case I need you again!
Thank you
Thank you
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
Upgrade your Whirlpool trash compactor with this authentic OEM SWITCH-OFF. Designed for select models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef appliances, this switch-off is integral for peak performance. Its function is to deactivate or reverse the motor to hoist the ram if the trash drawer falls out of alignment within the cabinet. To ensure the safety of the installation process, unplug the appliance or disconnect the house circuit breaker before starting. Because the size and shape of parts can vary slightly, it is advised to verify the compatibility of this specific switch-off with your model. Wear work gloves during the installation process for optimal hand protection.
Upgrade your Whirlpool trash compactor with this authentic OEM SWITCH-OFF. Designed for select models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef appliances, this switch-off is integral for peak performance. Its function is to deactivate or reverse the motor to hoist the ram if the trash drawer falls out of alignment within the cabinet. To ensure the safety of the installation process, unplug the appliance or disconnect the house circuit breaker before starting. Because the size and shape of parts can vary slightly, it is advised to verify the compatibility of this specific switch-off with your model. Wear work gloves during the installation process for optimal hand protection.
Installation Instructions
billy from HOUSTON, TX
My compactor is over 35 years old. Needed rebuild. Noisy. Quick cycle. Overload.
Replaced the bearing assembly at the base of both ram screws (worn out and noisy)
Replaced the drawer switch in the lower back (broken)
Replaced the top up/down switch (old and faulty)
Replaced the nylon ram nuts.
Replaced the control panel on/off/start switch.
Replaced the chain, and chain gear set.
Replaced ... Read more the motor.
Replaced both sets of drawer rollers.
Final cost in parts - $450 - new compactor $1100. Works like new.
Had to be creative in the 2 drawer switch as they are now longer offered for sale. Found suitable replacements.
This may be my last chance at repairing this.
Replaced the drawer switch in the lower back (broken)
Replaced the top up/down switch (old and faulty)
Replaced the nylon ram nuts.
Replaced the control panel on/off/start switch.
Replaced the chain, and chain gear set.
Replaced ... Read more the motor.
Replaced both sets of drawer rollers.
Final cost in parts - $450 - new compactor $1100. Works like new.
Had to be creative in the 2 drawer switch as they are now longer offered for sale. Found suitable replacements.
This may be my last chance at repairing this.
Read less
This rocker switch can be used for both the oven selector and/or the oven light.
This rocker switch can be used for both the oven selector and/or the oven light.
Installation Instructions
Peter from NAPA, CA
stop running
replaced rotary