KitchenAid Trash Compactor Parts

KitchenAid Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular KitchenAid Trash Compactor Parts

Your Price
$66.77
  On Order
Drive Gear Kit
★★★★★
★★★★★
46 Reviews
PartSelect Number PS398589
Manufacturer Part Number 882699
This is the drive gear kit for the ram that compacts the trash inside your compactor. If your compactor ram is getting stuck, there is excess noise during its cycle, or if your compactor does not stop at the end of its cycle, the driving gear may be the issue. The gear is white, plastic and approximately 4.5 inches in diameter. This drive gear kit includes both gears, pin spring, retaining clip (c-ring), ram stop, ram cam, and instructions. Make sure to disconnect the power to your trash compactor before beginning the repair.
Fixes these symptoms
  • Compactor ram gets stuck
  • Doesn’t stop at end of compacting cycle
  • Noisy
  • See more...
Installation Instructions
Asbjorn from The Woodlands, TX
Compactor stuck in lower position
Moved the compactor out from under cabinet and unplugged the powercable.Laid compactor over on its side Removed the top (4 screws) and base plate (3 screws) as well as the coverplate for the motor(3 screws)Found that large drive was broken in half. Used two screwdrivers to start split ring then pliers to pull it off the rest of the way.
Removed the drive gear and the washer.
Used a nail to drive out the pin for the smaller drive gear kit. Removed and replaced with new, used new pin to lock it on to the shaft. Changed out the bearings and washers on one powerscrew, put chain back on. Then was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Greased chain, gear drive and powerscrew. Put all covers back on with the screws. Pushed button it worked.
Read more...
Your Price
$26.18
  In Stock
15 Inch Compactor Bags - 15 Pack
★★★★★
★★★★★
3 Reviews
PartSelect Number PS1964579
Manufacturer Part Number W10165295RP
Trash compactor bags are a practical way to discard your waste. Due to the extreme pressure of the compactor, trash compactor bags designed to handle the force are necessary. These bags are made from tough 2.5-millimeter, multi-laminate plastic, and the patented Slip-Grip design prevents the bag from slipping into the compactor bin. They measure approximately 15 inches wide x 15 inches high and are made from 50 percent post-consumer recycled plastic. This pack of 15 trash compactor bags is a genuine OEM replacement part, and will fit most rectangular 15-inch trash compactors.
Installation Instructions
Sherry from SALEM, NY
Paper & Plastic 15” Compactor Bags not available
I have always used compactor bags made of paper & plastic. I was sent bags made of only plastic. I called and was told that is the only kind available. I am concerned that the plastic bags may not be strong enough.

I quest I will have to try these all plastic bags. I hope they are strong enough and work properly.
Read more...
Your Price
$6.04
  In Stock
Touch-Up Paint - White
★★★★★
★★★★★
1 Review
PartSelect Number PS385132
Manufacturer Part Number 72017
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
Installation Instructions
Michelle from Richardson, TX
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great. Read more...
Your Price
$58.16
  In Stock
Directional Switch
★★★★★
★★★★★
15 Reviews
PartSelect Number PS11744742
Manufacturer Part Number WP777811
The function of the directional switch on your trash compactor is to ensure the ram lowers to compress your trash, then returns to the top position. If your trash compactor does not complete this task, will not stop at the end of the compacting cycle, or is noisy during operation, you may need to replace the directional switch. Be sure to disconnect your trash compactor from the power source before completing this repair. This is a fairly easy repair. After you open the control panel of the compactor, all you will need to do is unplug the old switch from the electrical wires, and plug the new switch in.
Fixes these symptoms
  • Compactor ram gets stuck
  • Doesn’t stop at end of compacting cycle
  • Noisy
  • See more...
Installation Instructions
Scott from Indianapolis, IN
Trash Compactor ram wouldn't lower
I pulled the trash compactor out from under the counter.

I took out the four screws that kept the top cover in place to expose the ram.

The gear shafts were turning but the ram would not lower, at first I though the ram drive bolts were stripped and it wouldn't engage the shaft. Then I realized there was a mechanical directional\limit switch at the top that controlled the power and direction the gear shafts were turning, this switch was broken.

Just had to take off the front plate that was held on by a number of screws and replace the switch that was held on by two more screws. It had five wires attached to it, the new switch was clearly labeled as to which color wire went where.
Read more...
Your Price
$7.20
  In Stock
Foot, Front - Single
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11747965
Manufacturer Part Number WPW10001130
The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a rubber foot. It is important that when installing this part you are very careful, if not installed correctly your washer will be off balance which will then cause it to vibrate and/or shake during the cycle. The function of the adjustable foot is to keep your washing machine supported and to make sure that it is level at all times. The tools you will need for this repair include a pair of channel lock pliers, and a 9/16 wrench.
Installation Instructions
Paddy from Ferndale, WA
Bearings went out in the drum.
purchased the bearings at Napa auto parts for 16$. Over all it was a little difficult to get the bearings out and back in. Used a brass drift to drive them out and to seat them back in.. Read more...
Your Price
$41.14
  In Stock
Switch Knob
★★★★★
★★★★★
9 Reviews
PartSelect Number PS11747576
Manufacturer Part Number WP9871800
This start switch knob, also known as a rotary switch knob, is used for a trash compactor. The knob allows you to activate the compactor when the knob is turned or pushed. It comes in black and it measures about one and a half inches in diameter. Remove the knob by pulling it out of the switch. No tools are required for this easy replacement, but refer to the diagram and installation instructions provided by the manufacturer for accurate guidance and more detail.
Fixes these symptoms
Installation Instructions
Steffanie from Mill Valley, CA
Lost knob to trash compactor
Ordered the part here, had it delivered to my front door, and fixed it in LESS than 24 hrs.

Will definitely come back here, if I ever have a problem again. THANKS!!!
Read more...
Your Price
$34.68
  In Stock
15" Compactor Bag Carrier with Easy Grip Handles
★★★★★
★★★★★
10 Reviews
PartSelect Number PS1782408
Manufacturer Part Number 13030RP
This 15 inch compactor bag carrier fits around the compactor bag inside the compactor and is used to easily lift and remove trash compactor bags once they are full. Simply place the reusable bag carrier in the garbage can before placing a new compactor bag in the bin. The easy-grip handles make removal easier once the bag is full. This piece also makes a good carrier for bringing in logs for your fireplace. This part fits most 15 inch compactors. For the full list of compatible compactors, check the list below. Compactor bags are sold separately.
Installation Instructions
Edward from Deerfield Beach, FL
Change out defective switch
Pulled out compactor drawer and removed same, slid the compactor cabinet out and unpluged the appliance. Removed the two phillips head screws to release the control panel. lossened the locking nut from switch. matched the switches to be sure parts were the same,switched the wires to the new switch and reinstalled.replaced phillips screws, all Done !!! Read more...
Your Price
$15.84
  In Stock
Drawer Roller
★★★★★
★★★★★
6 Reviews
PartSelect Number PS11747573
Manufacturer Part Number WP9871602
This bearing roller may also be known as the wheel assembly or the container roller bearing, and it is a piece for your trash bin. The function of this bearing is to work in conjunction with your trash bin to allow the canister to roll free. For this repair you will need a nut driver, a pair of pliers, a screwdriver set, and an adjustable wrench. The most obvious symptom that will require you to replace this part is if your drawer is hard to open and/or close. Your appliance comes with two bearing rollers and it is sold individually.
Fixes these symptoms
Installation Instructions
John from Lancaster, CA
Roller was flat
Bought wrong roller. The drawer roller is different than the stationary rollers. Note the difference. Read more...
Your Price
$139.62
  In Stock
Rotary Switch Kit
★★★★★
★★★★★
14 Reviews
PartSelect Number PS382679
Manufacturer Part Number 675382
The rotary switch kit is also known as the start switch or the on and off switch, and is used to power on your trash compactor. The function of the rotary switch kit is to control the electrical power that is going into your trash compactor. This process happens when the switch sendsvoltage to the motor to start the compacting cycle. If your switch is broken the trash compactor will not start. A multimeter test can be performed to test the switch for continuity. The rotary switch kit will come with an on and off rotary switch, and two chrome knobs.
Fixes these symptoms
  • Doesn’t stop at end of compacting cycle
  • Won’t start
  • Won’t stay on
  • See more...
Installation Instructions
Edward from Deerfield Beach, FL
Change out defective switch
Pulled out compactor drawer and removed same, slid the compactor cabinet out and unpluged the appliance. Removed the two phillips head screws to release the control panel. lossened the locking nut from switch. matched the switches to be sure parts were the same,switched the wires to the new switch and reinstalled.replaced phillips screws, all Done !!! Read more...
Your Price
$4.33
  In Stock
Nut
PartSelect Number PS11744731
Manufacturer Part Number WP776356
Sold individually.

Appliance Type

Related Parts

Popular KitchenAid Trash Compactor Models

Below are the most popular KitchenAid Trash Compactor models we have. Enter your model number in the search box to find your model.