Roper Trash Compactor Parts
Popular Roper Trash Compactor Parts
Your Price
$58.57
In Stock
Roper Trash Compactor Drive Gear Kit
Removed the drive gear and the washer.
Used a nail to drive out the pin for the smaller drive gear kit. Removed and replaced with new, used new pin to lock it on to the shaft. Changed out the bearings and washers on one powerscrew, put chain back on. Then was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Greased chain, gear drive and powerscrew. Put all covers back on with the screws. Pushed button it worked. Read more...
PartSelect Number PS398589
Manufacturer Part Number 882699
This is the drive gear kit for the ram that compacts the trash inside your compactor. If your compactor ram is getting stuck, there is excess noise during its cycle, or if your compactor does not stop at the end of its cycle, the driving gear may be the issue. The gear is white, plastic and approximately 4.5 inches in diameter. This drive gear kit includes both gears, pin spring, retaining clip (c-ring), ram stop, ram cam, and instructions. Make sure to disconnect the power to your trash compactor before beginning the repair.
Fixes these symptoms
- Compactor ram gets stuck
- Doesn’t stop at end of compacting cycle
- Drawer is hard to open and or close
- See more...
Installation Instructions
Asbjorn from The Woodlands, TX
Compactor stuck in lower position
Moved the compactor out from under cabinet and unplugged the powercable.Laid compactor over on its side Removed the top (4 screws) and base plate (3 screws) as well as the coverplate for the motor(3 screws)Found that large drive was broken in half. Used two screwdrivers to start split ring then pliers to pull it off the rest of the way.Removed the drive gear and the washer.
Used a nail to drive out the pin for the smaller drive gear kit. Removed and replaced with new, used new pin to lock it on to the shaft. Changed out the bearings and washers on one powerscrew, put chain back on. Then was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Greased chain, gear drive and powerscrew. Put all covers back on with the screws. Pushed button it worked. Read more...
Your Price
$64.08
In Stock
Roper Trash Compactor Directional Switch
I took out the four screws that kept the top cover in place to expose the ram.
The gear shafts were turning but the ram would not lower, at first I though the ram drive bolts were stripped and it wouldn't engage the shaft. Then I realized there was a mechanical directional\limit switch at the top that controlled the power and direction the gear shafts were turning, this switch was broken.
Just had to take off the front plate that was held on by a number of screws and replace the switch that was held on by two more screws. It had five wires attached to it, the new switch was clearly labeled as to which color wire went where. Read more...
PartSelect Number PS11744742
Manufacturer Part Number WP777811
The function of the directional switch on your trash compactor is to ensure the ram lowers to compress your trash, then returns to the top position. If your trash compactor does not complete this task, will not stop at the end of the compacting cycle, or is noisy during operation, you may need to replace the directional switch. Be sure to disconnect your trash compactor from the power source before completing this repair. This is a fairly easy repair. After you open the control panel of the compactor, all you will need to do is unplug the old switch from the electrical wires, and plug the new switch in.
Fixes these symptoms
- Compactor ram gets stuck
- Doesn’t stop at end of compacting cycle
- Noisy
- See more...
Installation Instructions
Scott from Indianapolis, IN
Trash Compactor ram wouldn't lower
I pulled the trash compactor out from under the counter.I took out the four screws that kept the top cover in place to expose the ram.
The gear shafts were turning but the ram would not lower, at first I though the ram drive bolts were stripped and it wouldn't engage the shaft. Then I realized there was a mechanical directional\limit switch at the top that controlled the power and direction the gear shafts were turning, this switch was broken.
Just had to take off the front plate that was held on by a number of screws and replace the switch that was held on by two more screws. It had five wires attached to it, the new switch was clearly labeled as to which color wire went where. Read more...
Your Price
$16.38
In Stock
Roper Trash Compactor Drawer Roller
PartSelect Number PS11747573
Manufacturer Part Number WP9871602
This bearing roller may also be known as the wheel assembly or the container roller bearing, and it is a piece for your trash bin. The function of this bearing is to work in conjunction with your trash bin to allow the canister to roll free. For this repair you will need a nut driver, a pair of pliers, a screwdriver set, and an adjustable wrench. The most obvious symptom that will require you to replace this part is if your drawer is hard to open and/or close. Your appliance comes with two bearing rollers and it is sold individually.
Fixes these symptoms
- Drawer is hard to open and or close
- See more...
Installation Instructions
Michael from Morgan Hill, CA
Install NewDrive Gear Kit,( I also added,2 poor nuts and all 4 wheels)
My compactor is quite heavy, I moved it onto the kitchen floor unplugged and removed the cover plate from the bottom exposing the drive gears. The small (pinion ) gear was stripped as well as a section of the drive gear. I followed the video and removed the (fulthy) ram. The interior filth was so great I removed all parts to my garage and spent a lot of time cleaning them especially the ram.By the time my parts arrived, it was all clean and ready to go. I had also found that one of the power nuts was broken and had ordered new wheels and power nuts. Assembly was straight forward and it works like new now,
Read more...
Your Price
$26.14
In Stock
Roper Trash Compactor Wheel Assembly - Kit of 2
PartSelect Number PS398587
Manufacturer Part Number 882688
This wheel assembly, or roller assembly, is for a trash compactor. The kit includes two wheels that are approximately 1 inch in diameter each. The wheels allow the trash compactor container to roll in and out of the appliance. You may have to replace the wheel assembly if the container does not roll smoothly. To access the existing wheel kit on your appliance, uninstall appliance from the cabinet, depress foot petal to lift the container off its track, and remove the container from the tracks. This kit is an OEM part sourced from the authentic manufacturer factory.
Fixes these symptoms
- Drawer is hard to open and or close
- See more...
Installation Instructions
Michael from Morgan Hill, CA
Install NewDrive Gear Kit,( I also added,2 poor nuts and all 4 wheels)
My compactor is quite heavy, I moved it onto the kitchen floor unplugged and removed the cover plate from the bottom exposing the drive gears. The small (pinion ) gear was stripped as well as a section of the drive gear. I followed the video and removed the (fulthy) ram. The interior filth was so great I removed all parts to my garage and spent a lot of time cleaning them especially the ram.By the time my parts arrived, it was all clean and ready to go. I had also found that one of the power nuts was broken and had ordered new wheels and power nuts. Assembly was straight forward and it works like new now,
Read more...
Your Price
$56.16
In Stock
Roper Trash Compactor Power Nut
PartSelect Number PS11744741
Manufacturer Part Number WP777533
This part is a power nut, and it is intended to be used in conjunction with trash compactors. The function of this nut is to fasten to the side of the ram where it is threaded. When the power screw rotates, it is fed through the power nut, which pulls the ram down to compress the trash. This part is just over an inch in diameter, and is just one inch thick. This part is white and made entirely of plastic. The reason for needing to replace this part is if your compactor ram gets stuck, or if it does not stop at the end of the compacting cycle.
Fixes these symptoms
- Compactor ram gets stuck
- Doesn’t stop at end of compacting cycle
- See more...
Installation Instructions
Janet W. from Shreveport, LA
Compactor out of line and would not shut off.
Pulled compactor out on a piece of cardboard. Used socket set to take top off and evaluate the problem. Power nut was not holding on one side. We ordered two power nuts. Decided to repair only the unlevel side. Fast and easy and cheaper than a new compactor. Whirlpool compactor is 28 years old and working like a charm. Thanks for the diagram and accessibility to parts.
Read more...
Your Price
$102.63
In Stock
Roper Trash Compactor Rotary Switch Kit
PartSelect Number PS382679
Manufacturer Part Number 675382
The rotary switch kit is also known as the start switch or the on and off switch, and is used to power on your trash compactor. The function of the rotary switch kit is to control the electrical power that is going into your trash compactor. This process happens when the switch sendsvoltage to the motor to start the compacting cycle. If your switch is broken the trash compactor will not start. A multimeter test can be performed to test the switch for continuity. The rotary switch kit will come with an on and off rotary switch, and two chrome knobs.
Fixes these symptoms
- Doesn’t stop at end of compacting cycle
- Won’t start
- Won’t stay on
- See more...
Installation Instructions
Edward from Deerfield Beach, FL
Change out defective switch
Pulled out compactor drawer and removed same, slid the compactor cabinet out and unpluged the appliance. Removed the two phillips head screws to release the control panel. lossened the locking nut from switch. matched the switches to be sure parts were the same,switched the wires to the new switch and reinstalled.replaced phillips screws, all Done !!!
Read more...
Your Price
$153.61
On Order
Roper Trash Compactor Drawer Handle - Black
Very easy.
Cannot thank you enough. Sears said the parts were not made anymore. We were upset as rest of compactor was fine,but we had a torn guard and a cracked handle. Price of a new compactor was a fortune. But thanks to you. LEss than $50 good as new.
Someone needs to tell sears they are really missing out. You had a shelf we needed about 4 months ago and it was exactly what we needed,so we knew if anyone could help us it would be you. You were right on.
Thank you so much Read more...
PartSelect Number PS11743097
Manufacturer Part Number WP608732
This part is now brown instead of black.
Fixes these symptoms
- Drawer is hard to open and or close
- See more...
Installation Instructions
wendy from Sandy, UT
Both parts needed replacing. Could not find a replacement until you.
Pulled out old screws. Replaced with new screws.Very easy.
Cannot thank you enough. Sears said the parts were not made anymore. We were upset as rest of compactor was fine,but we had a torn guard and a cracked handle. Price of a new compactor was a fortune. But thanks to you. LEss than $50 good as new.
Someone needs to tell sears they are really missing out. You had a shelf we needed about 4 months ago and it was exactly what we needed,so we knew if anyone could help us it would be you. You were right on.
Thank you so much Read more...
Your Price
$5.37
In Stock
Roper Trash Compactor Nut
PartSelect Number PS11744731
Manufacturer Part Number WP776356
This nut is a genuine OEM part for a variety of trash compactors. Made of high-quality metal, the flat side of this washer faces and is fastened to the side of your trash compactor to secure the railing system to the main drawer of the compactor.
Installation Instructions
DONNA from SHERMAN, TX
Control knob broke
The repair was easy, just wish I hadn't waited so long to decide to fix it!
Read more...
Your Price
$7.55
In Stock
Your Price
$34.16
In Stock
Roper Trash Compactor Light Switch
Thank you Read more...
PartSelect Number PS11742478
Manufacturer Part Number WP4387911
The light switch terminal is used in refrigerators and freezers to allow you to see inside your appliance by turning on when the fridge door is open and turning off when the door is closed. This part is 1.12 inches in length, 1 inches in width, and 1.75 inches in height. It weighs 0.026 pounds. If your light switch terminal is damaged or the light does not turn on when fridge door is open, replacing the light switch terminal can fix the problem. As a safety precaution, remember to unplug your fridge from the power source before beginning this installation. Refer to the manual provided by the manufacturer for further installation instructions and a detailed guide.
Fixes these symptoms
- Light not working
- See more...
Installation Instructions
Darlene from Holland, MI
Light switch broke on refridgerator door.
I measured the part then looked for a similar switch that might work. I was so happy to find the exact part we needed for our 24 year old refridgerator!! I was so impressed with your slection of parts and best of all I had the part in 2 days! You are in my "favorites" just in case I need you again!Thank you Read more...
Roper Trash Compactor Appliance Types
Related Roper Trash Compactor Parts
Popular Roper Trash Compactor Models
Below are the most popular Roper Trash Compactor models we have. Enter your model number in the search box to find your model.
