Roper Range Igniters

Roper Appliance Parts
Shop By Part Type

Popular Roper Range Igniters

Your Price
$76.18
  In Stock
Round Style Oven Igniter
★★★★★
★★★★★
(49)
PartSelect Number PS243425
Manufacturer Part Number WB2X9154
The round style oven igniter is also known as an oven bake or broil igniter and is compatible with your range appliance. The function of the round style oven igniter is to pull electrical current through the oven safety valve to open it. If your igniter is glowing for more than ninety seconds but it has not ignited the gas flame, that means that the igniter is not powerful enough to open the valve. Be very careful when handling this igniter as it is very fragile. This igniter has a range of 2.5 to 3.0 amps. Note that this round igniter will not replace flat style igniters.
Fixes these symptoms
  • Element will not heat
  • Gas igniter glows, but will not light
  • Little to no heat when baking
  • See more...
Installation Instructions
Mark from Upland, CA
No ignition
Unplug the oven.
Open the oven door.
Remove the racks.
Remove the two screws that hold the oven floor; they are located toward the back.
Remove the oven floor pan.
Remove the screw holding the heat shield/dispenser.
Remove the heat shield/dispenser.
Untwist the ceramic wire caps on the two igniter wires.
Remove the two screws holding the igniter.
Remove the igniter.
Replace the igniter working all the steps backwards.
It’s super simple.
Read more...
Your Price
$54.02
  On Order
Bake Igniter
★★★★★
★★★★★
(24)
PartSelect Number PS11747217
Manufacturer Part Number WP9758079
This part ignites the gas to light the oven burner.
Fixes these symptoms
  • Element will not heat
  • Gas igniter glows, but will not light
  • Gas smell
  • See more...
Installation Instructions
Greg from North Baltimore, OH
Bake/broil would not work
Replaced igniter and also DSI/direct spark igniter did not fix problem. Called out repairman turned out to be bad gas valve. Replaced that part , now stove works fine. Read more...
Your Price
$53.96
  In Stock
Igniter-OVEN
★★★★★
★★★★★
(29)
PartSelect Number PS11770066
Manufacturer Part Number W10918546
This flat style gas oven igniter has ceramic housing and comes with a connector.
Fixes these symptoms
  • Element will not heat
  • Gas igniter glows, but will not light
  • Little to no heat when baking
  • See more...
Installation Instructions
sharnette from baltimore, MD
our oven would not heat up
My husband pulled out the stove turned the gas off then he pulled out the part and replaced igniter....it took only about 20 min to do this job it was very easy and prior to us doing ourselves i called a well known company that does home repairs, I also called a few smaller businesses and to replace this part was anywhere from $175- 250 if not more. we are very very happy with our decision to replace the part ourselves unstead of spending extra money we didnt have . Read more...
Your Price
$29.33
  In Stock
Surface Burner Spark Igniter
★★★★★
★★★★★
(7)
PartSelect Number PS11746068
Manufacturer Part Number WP8523793
This part helps your burner ignite and produce flame.
Fixes these symptoms
  • Element will not heat
  • Gas igniter glows, but will not light
  • Will Not Start
  • See more...
Installation Instructions
Daniel from Needham, MA
spark igniter was weak and not lighting the flame.
Open top oven door and remove the 2 front screws which hold the burners and controls to the frame. DO NOT lift the burners more than an inch or so to look inside. You WILL bend the gas lines in the back if you do. Pull out stove from the wall, shut off gas supply and disconnect hose if needed to have room to work. Remove top back panel and remove the 3 wires connecting the top burner assembly and also remove the 2 gas lines. Now you will be able to remove the burner assembly safely. Flip it over and try to unscrew the screw holding the igniter. When you fail, drill it out and get a small metal screw to replace it. The metal is soft and the screw is hard, so drill carefully. The rest is easy, put in the new igniter and screw. and put it back together. Read more...
Your Price
$57.94
  In Stock
Flat Style Oven Igniter
★★★★★
★★★★★
(10)
PartSelect Number PS387058
Manufacturer Part Number 786324
The flat style oven igniter is also known as a range oven igniter. The function of this part is to glow extremely hot in order to ignite the gas for the oven burner. With this flat style oven igniter, you must reuse the original bracket from your original igniter. Be very careful during installation to not touch the black element part of the flat style oven igniter as it is very fragile. If your oven does not heat you should check to see if your igniter is glowing. If your igniter is glowing and the oven is not heating there is a chance that the igniter is not strong enough to heat your oven and it will need to be replaced.
Fixes these symptoms
  • Element will not heat
  • Gas igniter glows, but will not light
  • Little to no heat when baking
  • See more...
Installation Instructions
John from Niles, MI
Oven wouldn't heat. Glow ignitor was weak and wouldn't ignite flame.
After shutting off the gas and removing the oven door, which simply slid off of the hinges, I removed the oven plate. The ignitor was attached to the manifold. I removed that and noted the wires were attached back behind a hole in the back of the oven. I thought I would have to access them from the back but when I pulled on them I was able to reach them from the front. I was surprised to find plastic lugs covering the wire ends, rather than ceramic. I attached the new ignitor wires and reused the plastic lugs, as no ceramic ones came with the new ignitor. I carefully slid the new ignitor back into the cage/shield attached to the manifold and replaced the manifold. I then turned the gas back on and tested the ignitor (which worked perfectly) before replacing the oven plate. The repair took less than 30 minutes, but my wife and I thoroughly cleaned the door and interior while we had it apart. The hardest part was getting the door back on the hinges, but this too was accomplished after several attempts. The oven heats up beautifully now. Read more...
Your Price
$32.59
  In Stock
Spark Igniter
★★★★★
★★★★★
(6)
PartSelect Number PS11770331
Manufacturer Part Number W11032529
This is the replacement spark igniter or surface burner igniter for your range. This igniter has a blue tube, but the tube can come in a variety of colors, and still do the same job. The spark igniter produces the spark that lights the surface burner. The main reason to replace the igniter is if the wires shorts out, or the porcelain has cracked, and it will no longer produce a spark. If your gas igniter glows but will not light, it is a good indication that the spark igniter will need to be replaced. Be sure to turn off the gas to the range before you complete this repair. This part is sold individually and is an OEM part.
Fixes these symptoms
  • Gas igniter glows, but will not light
  • Will Not Start
  • See more...
Installation Instructions
Gabriel from DENVER, CO
TOP RANGES WILL NOT LIGHT
I use the table knife to slide the side of the stove to open the top. then I traced one of the wire to where it was hooked up and remove it and replaced it. I did them one by one. Read more...
Your Price
$53.93
  In Stock
Round Carborundum Oven Igniter
★★★★★
★★★★★
(11)
PartSelect Number PS360921
Manufacturer Part Number 4342528
This round style gas oven igniter, or also known as a broil or bake igniter, has an amperage range between 2.5 and 3.0. It glows white hot to ignite the gas for the oven. The igniter does this by attracting electrical currents through the safety valve to open it. *Please note: this does not replace the flat style igniters. If your gas igniter does not start, glows but does not light, or produces little to no heat when baking, replacing this part could be the solution to your problem. Refer to the diagram provided by the manufacturer for further instructions and guidance.
Fixes these symptoms
  • Element will not heat
  • Gas igniter glows, but will not light
  • Little to no heat when baking
  • See more...
Installation Instructions
Mark from Rego Park, NY
The lower burner would not ignite.
First I removed the oven racks. Then I loosened the two screws in the back of the oven floor and figured out how to remove it. Then I loosened the two screws at the front of the diverter and, with some pushing and pulling and twisting, was able to get that to come out, too. Then I tried lighting the oven and noticed that the igniter was not glowing. When I saw that the upper (broiler) burner was working fine, I hoped that the problem was the lower igniter itself. I checked the wires and they seemed fine. I saw that two bolts held the igniter onto its bracket, so with a socket wrench (which size I got right on the first guess!) I removed those bolts and the igniter came loose. I found the connecter for the wires when I removed the drawer under the oven and was able to pull it apart easily. The igniter came out completely. There was nothing unusual about it, but I decided to take a chance and order a new one, hoping that replacing it would solve the problem. I put the rest of the oven together and waited. About three days later the part arrived (it was sent on a holiday; FedEx is soooo much better than USPS). I retraced the steps of taking the oven apart, put the two bolts into the new igniter to attach it to the bracket, and went back underneath behind the drawer to connect the wires. Then came the moment of truth: I tried turing on the oven. I held the button down to keep the light off, and after a few seconds I saw it: IT GLOWED!! It worked!! After yelling a satisfying "YEAH!!," I turned it off, put back the drawer, the diverter (more pulling and pushing and twisting), and the oven floor. Now it's all working perfectly and it took a very short time to fix. And a little luck that the problem was with such a simple part. Read more...
Your Price
$49.70
  In Stock
Surface Igniter (RF, RR & LF)
★★★★★
★★★★★
(1)
PartSelect Number PS11750430
Manufacturer Part Number WPW10209656
Also known as spark electrode. This part helps your burner ignite and produce flame.
Fixes these symptoms
  • Gas igniter glows, but will not light
  • Will Not Start
  • See more...
Your Price
$64.71
  In Stock
Broil Igniter
PartSelect Number PS11744847
Manufacturer Part Number WP8054129
This part ignites the gas to light the oven burner.
Fixes these symptoms
  • Gas igniter glows, but will not light
  • Little to no heat when baking
  • Little to no heat when broiling
  • See more...
Your Price
$85.36
  In Stock
Oven Igniter
★★★★★
★★★★★
(1)
PartSelect Number PS11740875
Manufacturer Part Number WP3186491
This part is used to light the oven for the bake or broil.
Fixes these symptoms
  • Gas igniter glows, but will not light
  • Little to no heat when baking
  • Will Not Start
  • See more...
Installation Instructions
Robert from Sun City, CA
The (relatively new) gas oven would not light...oddly enough after a power outage. The recommended typical troubleshooting experience was that if the oven will not light: replace the igniter, even if it appears to be working fine.
I had already removed the 2 plates in the bottom of the oven to take an initial look. After not finding anything obvious, and searching on line for advice, I ordered the igniter. After the igniter arrived it was a matter of removing 2 screws, pulling out the lower drawer to gain access to the igniter disconnect, and done.

thanks for getting the correct part to me so quickly. Also the diagram and part number search was right on the money!
Read more...

Related Parts