Ridgid Parts

It is a genuine OEM sourced 5-inch sanding pad assembly that is specially designed for use with Craftsman orbital sanders. Its purpose is to provide support for hook and loop sandpaper, unfortunately, over time it may wear out or get damaged eventually requiring a replacement. To make the pad last longer do not put to much pressure on the sander when using it, the pressure will create heat and ruin the small hooks on the pad. To replace the pad simply remove the four screws attaching it to the sander and replace it with the new pad. Please note this high-quality component is sold individually.

Genuine Ridgid replacement part. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • Parts are sold individually • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. • Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. • Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. • A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. • When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

This is a Genuine Manufacturer Sourced replacement part. This is a Carbon Brush with Lead Wire attached and a Spring. This Brush is Sold Individually. Please note Brush Holder is Sold Separately. Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. It is recommended to replace both brushes at the same time. You would need a Screwdriver and Pliers to complete this job.

Genuine Ridgid replacement part, this item is sold individually. The purpose of the 29823 Caster it to make the Vacuums shown below more mobile. To replace the Caster , pull on it and remove it from the Caster Foot, then just simply press the new caster back in.

This is a genuine OEM sourced replacement part designed for use with Ridgid tile saws. This assembly includes one (1) carbon brush with a lead wire and a spring attached. Please note brush holder is sold separately. Carbon brushes are a commonly replaced part on power tools. Due to normal use and friction brushes will gradually wear down and will require replacement. It is advised to replace both brushes at the same type. You would need a screwdriver to complete this job. • Make sure the unit is unplugged • First remove brush caps • Take out old brushes and replace them with new ones • Secure brush caps

Genuine Ridgid replacement part, this item is sold individually. 2 of these Brushes are needed for a set. This Brush includes the Brush, Brush Holder, Brush Spring and plug in terminal. It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Sleeves, also known as tool holders/adapters, are used to allow you to connect other accessories to a multi-tool, holding and securing them in the process. This sleeve has an approximately 3/4-inch outer diameter and 1/4-inch inner diameter/bore and is compatible with different models of multi-tool. Because this part is a high-use part, it is recommended that you order multiple to avoid running out in the future. To avoid having to replace it as often, make sure to clean the sleeve after each use and handle it with care. If you notice high wear on the sleeve or have difficulty keeping attachments connected, it likely needs to be replaced. To replace it, you may need an Allen wrench, screwdriver or other tools.

Genuine Ridgid replacement part Set of 2 Carbon Brushes with wire lead and brush spring attached. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that's operating intermittently. • New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.