Range Caps and Lids
Popular Range Caps and Lids
Your Price
$34.24
In Stock
Range COVER LED Assembly
PartSelect Number PS4704284
Manufacturer Part Number WR55X11132
COVER LED Assembly FF
Fixes these symptoms
- Light not working
- See more...
Installation Instructions
DON from SAN ANTONIO, TX
LAMP WAS BURNED OUT
EXCHANGED THE LED LAMP ASSEMBLY. ONLY DO ONE AT A TIME AS THEY ARE WIRED IN SERIES!
Read more...
Your Price
$24.33
In Stock
Range CAP
PartSelect Number PS11775705
Manufacturer Part Number 5304508442
The surface Meduim 9.5K burner cap is located on the top of the burner head and is used in ranges and ovens. The burner cap helps spread out the burner flame for even heating, and protects the burner head from cooking spills. Without the cap you can have a burning gas torch. If your cap is missing or is discolored, replacing this part can solve the issue. This part comes in the color black. Remember to unplug your range from the power source and allow surface to cool before installing this part. Refer to the manual provided by the manufacturer for further installation instructions.
Your Price
$30.05
In Stock
Range CAP
PartSelect Number PS11775704
Manufacturer Part Number 5304508441
Sold individually. This part helps the flame to spread for even heat. Also protects your burner head from spills.
Your Price
$14.87
In Stock
Range Wave Guide Cover
PartSelect Number PS12071278
Manufacturer Part Number 5304509435
This OEM waveguide cover in your microwave is a heat-resistant component that prevents food, grease, and moisture from entering the waveguide. It is typically located on the side or top wall of the cooking chamber. If the cover is broken, you may notice cracks, charring, or burns, and potentially see arcing or sparks during operation. Not replacing a damaged cover can lead to short circuits and the risk of electrical components touching your food. To remove the cover, start by disconnecting the microwave from its power source before opening its door. The waveguide cover is slotted or snapped into place, so gently slide or apply pressure to release it from the clips or slots. Please note that the cover is sold individually.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Christopher from CARY, NC
Cover needs replacing
You have to be very careful because the wave guide cover is very brittle. It needs to be bent very gently in order to fit the four ends into each slot. I would highly recommend buying two just in case the first one breaks.
Read more...
Your Price
$35.46
In Stock
Range CAP
PartSelect Number PS11775706
Manufacturer Part Number 5304508443
This black burner cap is a genuine OEM part made of a durable material capable of reaching 14,000-BTU, with an approximately 3-inch diameter. It is compatible with various models of ranges and cooktops, where it helps to distribute heat evenly and protects the burner assembly from thermal damage. Since this cap is sold as an individual part, consider how many caps you need to replace on your stovetop before ordering. Burner caps often need to be replaced if they are damaged or worn, no longer providing even heat distribution, or if they simply no longer look good. To replace this cap, make sure the stovetop is cool, and then simply lift any necessary grates to get access to the cap. Then lift and swap out the old cap for the new one, making sure it is settled properly on the burner before you reseat the grate(s).
Your Price
$37.85
In Stock
Your Price
$24.06
In Stock
Your Price
$57.07
In Stock
Your Price
$47.91
In Stock
Range COVER-PLT
PartSelect Number PS11769950
Manufacturer Part Number W10915651
Installation Instructions
Kerry from Carrollton, TX
Part worn out
Could not complete the repair due to broken part when arrived. Reached out to service department but have not heard back. Maybe email did not go through due to pictures attached of part condition once arrived.
Read more...
Your Price
$95.37
In Stock