Official Norge Washer Parts

Affresh Washing Machine Cleaner - 3 pack – Part Number: W10135699

Your Price

$12.58

Norge Washer Affresh Washing Machine Cleaner - 3 pack

★★★★★

2 Reviews

PartSelect Number PS1960673

Manufacturer Part Number W10135699

This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.

Installation Instructions

Mary from ROANOKE RAPID, NC

Baker burner burned out.

Unplug the stove from the electric. Took out two screws in oven, placed burner into oven into the open slops and replace the screws.
Open back panel by removing two screws. Attach the two plugs to the burner and close back panel with the two screws. Plug-in stove and checked oven. Read more...

Videos!

Drive Belt - 51 inches long – Part Number: WP21352320

Your Price

$10.97

Norge Washer Drive Belt - 51 inches long

★★★★★

25 Reviews

PartSelect Number PS11738882

Manufacturer Part Number WP21352320

This V-style drive belt measures 51 inches long and 3/8 inches wide. The belt is made to slip on the motor pulley to bring the basket up to the speed required. Continued use can result in the belt suffering from wear and tear. Replace the V-style drive belt if you notice that it looks damaged. The most common symptoms of a damaged drive belt include: a burning smell or a loud grinding noise coming from the washer; the drum will not spin, spins slowly, or will not agitate; the washer shakes and moves, will not start, or will not drain.

Fixes these symptoms

Burning smell
Leaking
Spinning Issues
See more...

Installation Instructions

Ranse from Layton, UT

Pump was making a grinding noise

The pump is located behind a small panel on the back, lower left side of my washer. It's attached to the bottom frame with 3 screws. It has two hoses attached, each with one spring clamp. Lift one side of the washer and slip the drive belt off the pully. Release the spring clamps on the hoses with a pair of pliers and remove the hoses. A small amount of water will drain from the hoses and pump when removed. Remove the three screws holding the pump to the frame and remove the pump. Install the new pump in the same position. Reattach the hoses, replace the belt, and reinstall the cover panel. That's all there is to it. Read more...

Videos!

Transmission Pulley and Bearing Kit – Part Number: 12002213

Your Price

$60.72

Norge Washer Transmission Pulley and Bearing Kit

★★★★★

16 Reviews

PartSelect Number PS2003651

Manufacturer Part Number 12002213

This transmission pulley and bearing kit, also known as thrust bearing kit or washer pulley and bearing kit, includes the pulley, washer, thrust bearing, two upper race washers, and one lower race washer. These genuine Whirlpool parts are plastic and are not sold individually. The kit is used to help the washer drain, and may need to be replaced if the washer is experiencing slow or no spin, will not drain, or has no agitation. The washer will need to be tilted on its back or side to access the bottom. The tools needed to complete this repair are a small flat blade screw driver and a pair of slip joint pliers.

Fixes these symptoms

Burning smell
Spinning Issues
Spins slowly
See more...

Installation Instructions

James from Hueytown, AL

Washer tub would not spin, pump would empty water from tub.

Lay washer on front, removed belt. Removed center pulley with thrust bearing (pulley was worn on upper end, against thrust bearing, thrust bearing was worn also). Installed new thrust bearing & pulley kit. Cleaned & lubed slots that motor insulators slide in, installed new belt. Read more...

Videos!

Your Price

$13.09

Norge Washer Snubber Ring

★★★★★

16 Reviews

PartSelect Number PS11738845

Manufacturer Part Number WP21002026

The snubber ring is a piece that is specific to your washing machine. The function of the snubber ring is to reduce noise and vibrations within your washer. It fits in between the leg and the dome assembly. If during your spin cycle you notice your washer jumping and making loud whirring noises, you may need to replace your snubber ring. The tools you will need for this repair include: a putty knife, a 5/16 nut driver, a 1/4 inch nut driver, a 3/8 socket and a ratchet, a small flat blade screwdriver, a pair of locking pliers, and a pair of slip joint pliers.

Fixes these symptoms

Shaking and Moving
Spins slowly
Will not agitate
See more...

Installation Instructions

David from Butler, PA

Washer jumping in spin cycle (white flakes under the washer)

Unlug the AC cord,open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back (I removed the back cover also) and the little hose going to the basket. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING (DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK) Install the new ring, tighten the screws and put the tub back in connecting everything back up and use the 6 new springs. It really isn't that hard to do. Read more...

Videos!

Your Price

$11.17

Norge Washer Lid Hinge

★★★★★

25 Reviews

PartSelect Number PS11741780

Manufacturer Part Number WP35-2044

The lid hinge on your washer is connected to the lid and allows it to open and close. If you find you cannot open or close the lid to your washing machine properly, you may need to replace the lid hinge. This lid hinge is an inch and a half long, all white in color, and it is made entirely of plastic. To complete this repair, you will need a Phillips screwdriver and a putty knife to remove the top of the washer, in order to access the screws that hold the lid hinge in place. Be sure to disconnect the power to the washing machine before beginning this repair.

Fixes these symptoms

Lid or door won’t close
Will Not Start
See more...

Installation Instructions

Allen from North Little Rock, AR

One of the plastic hinge pins brroke

I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated. Read more...

Videos!

Your Price

$11.77

Norge Washer Hose Clamp

★★★★★

1 Review

PartSelect Number PS11743008

Manufacturer Part Number WP596669

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.

Fixes these symptoms

Leaking
See more...

Installation Instructions

jeff from lindenhurst, IL

Washing Machine was leaking water

Loosened the hose clamp, removed the injector valve and injector nozzle assembly, replaced both and tightened with new hose clamp. Fixed the problem for less than $20!! Washing machine is 20 years old and this was the first problem--hopefully it is now good for another 20 years! Read more...

Affresh Washing Machine Cleaner Tablets – 6 Count – Part Number: W10501250

Your Price

$21.14

Norge Washer Affresh Washing Machine Cleaner Tablets – 6 Count

PartSelect Number PS12345661

Manufacturer Part Number W10501250

This Affresh Washing Machine Cleaner deep cleans to help remove the odor-causing residues and grime that daily loads leave behind. The time-release tablets are EPA Safer Choice certified, septic-safe and designed to clean inside all machines, including HE (High Efficiency). Use monthly or every 30 cycles for a consistently clean machine.

Videos!

Your Price

$22.22

Norge Washer Lid Hinge Pin

★★★★★

10 Reviews

PartSelect Number PS11741781

Manufacturer Part Number WP35-2045

This lid hinge pin allows a washing machine lid to pivot open and closed properly. The hinge pin may need to be replaced if the lid will not open or will not close. The part is white and made of plastic. This lid hinge pin is just over an inch long, is sold individually, and does not include the mounting screw (consider ordering mounting screw if it rusted or stripped). It is recommended to check the opposite lid hinge pin before ordering because hinges may wear at the same rate. Be sure to not tighten the mounting screw to pin too tightly to avoid breaking the new part.

Fixes these symptoms

Lid or door won’t close
Will Not Start
See more...

Installation Instructions

Allen from North Little Rock, AR

One of the plastic hinge pins brroke

I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated. Read more...

Videos!

Your Price

$11.09

Norge Washer Hose Clamp

★★★★★

2 Reviews

PartSelect Number PS11740613

Manufacturer Part Number WP285655

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.

Fixes these symptoms

Leaking
Will not drain
See more...

Installation Instructions

Stephen from Laveen, AZ

Drive Pump Leaked

It took some trial and error but overall not a difficult project. 1. Take the front covers off. 2. Undo the pully spring to loosen belt 3. Remove belt off idler pulley wheel and free up belt from the large wheel. 4. Disconect the wiring harness and the hoses. 5. Undo the motor mounting bolts (4) 6. Take motor out of washer and remove the 3 screws holding the pump to the motor. 7. The pump had melted to the shaft and required I chisel the pump off of the shaft. 8. Attach new pump paying attention to where the belt is positioned. 9. Reattach the motor bolts, hoses, and wiring harnes. 10. Attach the belt and test the pump. 11. Put the front back on. Read more...