My Orders
Norge Washer Hardware
GET YOUR OFFICIAL Norge PARTS TO ENSURE VICTORY
Shop By Part Type
View MorePopular Norge Washer Hardware
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.
Installation Instructions
jeff from lindenhurst, IL
Washing Machine was leaking water
Loosened the hose clamp, removed the injector valve and injector nozzle assembly, replaced both and tightened with new hose clamp. Fixed the problem for less than $20!! Washing machine is 20 years old and this was the first problem--hopefully it is now good for another 20 years!
This screw is sold individually.
This screw is sold individually.
Installation Instructions
Alexander from Lakeland, FL
Broken Dryer Knob
First let me just say that Partselect.com is now one my stored favorites in my web browser. I came home from a business trip and saw a pair of pliers on the dryer. I thought that was odd until my wife informed me that the knob on the dryer had broken. So she was using the pliers to select the cycle. Somehow she knew where the missing p
... Read more
ointer was actually pointing. Since the dryer was over 5 years old I saw this as an opportunity to upgrade both appliances. Not with my frugal wife. A search of the Internet popped up partselect. I ordered Wednesday morning and the parts where on my doorstep late Thursday. Trust me I was very surprised. Everything worked perfectly. Two thumbs up!!!
Read less
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.
Installation Instructions
Stephen from Laveen, AZ
Drive Pump Leaked
It took some trial and error but overall not a difficult project. 1. Take the front covers off. 2. Undo the pully spring to loosen belt 3. Remove belt off idler pulley wheel and free up belt from the large wheel. 4. Disconect the wiring harness and the hoses. 5. Undo the motor mounting bolts (4) 6. Take motor out of washer an
... Read more
d remove the 3 screws holding the pump to the motor. 7. The pump had melted to the shaft and required I chisel the pump off of the shaft. 8. Attach new pump paying attention to where the belt is positioned. 9. Reattach the motor bolts, hoses, and wiring harnes. 10. Attach the belt and test the pump. 11. Put the front back on.
Read less
Sold individually.
Sold individually.
Installation Instructions
Peter from WRENTHAM, MA
Kenmore 80 Series Washer - Agitator Stopped Working
First I screamed at the ceiling, because I have a three year old and an infant, and the washing machine was dead. Then I went to youtube. It seemed like the "agitator dogs" were the issue.
In this spirit of any repair, I replaced them, and it was not the issue. I don't know what I expected.
Ceiling. YouTube. Pacing ... Read more .
Then I figured it was this part - the motor coupling. I unplugged the machine and took out the drain tube. I leaned the machine back and propped it up with an empty detergent bottle, because those were abundant. Ratchet off a few bolts and the motor comes out. The coupling was indeed broken. The new one slips right in - I tapped it a few times with a mallet for good measure / vengeance. Ratcheted the bolts back on and tipped it back up.
Pros: Washer works now.
Cons: Everest-esque laundry pile to address.
But hey, it worked! I am no handyman and it wasn't too bad at all. Half hour tops.
In this spirit of any repair, I replaced them, and it was not the issue. I don't know what I expected.
Ceiling. YouTube. Pacing ... Read more .
Then I figured it was this part - the motor coupling. I unplugged the machine and took out the drain tube. I leaned the machine back and propped it up with an empty detergent bottle, because those were abundant. Ratchet off a few bolts and the motor comes out. The coupling was indeed broken. The new one slips right in - I tapped it a few times with a mallet for good measure / vengeance. Ratcheted the bolts back on and tipped it back up.
Pros: Washer works now.
Cons: Everest-esque laundry pile to address.
But hey, it worked! I am no handyman and it wasn't too bad at all. Half hour tops.
Read less
Sold individually.
Sold individually.
Installation Instructions
Michael from Torrance, CA
lower left shelf support was broken
I removed all contents from the lower shelf. I, then removed both of the pull out drawers. Secondly, I removed the lower glass shelf and the glass support tray. At this point all four plastic shelf supports were accessible. I removed the inner screw from all four supports and replaced with four new shelf supports. Then reassembled in reve
... Read more
rse order. Very easy to do!
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This screw is sold individually.
This screw is sold individually.
Installation Instructions
Enrique from Tigard, OR
The refrigerator door was difficult to maintain closed
Because the lower cams are made out of hard plastic the repeated opening and closing of the door wore them out. The hardest part was taking all of the food that is normally stored in the door.
First step was to determine whether the screws were metric or US standard - they are metric. The next step was to remove the top hinge ... Read more in order to remove the door and replace the bottom cams and brackets. This took a couple of minutes, replacing the cams was about 5 minutes and putting the door back on the pivot and reattaching the top hinge was another couple of minutes.
If I had called a service tech they would have charged a minimum of two hour and for the parts. I estimate that I saved myself about $100.
First step was to determine whether the screws were metric or US standard - they are metric. The next step was to remove the top hinge ... Read more in order to remove the door and replace the bottom cams and brackets. This took a couple of minutes, replacing the cams was about 5 minutes and putting the door back on the pivot and reattaching the top hinge was another couple of minutes.
If I had called a service tech they would have charged a minimum of two hour and for the parts. I estimate that I saved myself about $100.
Read less
This screw is less than an inch long. It is a metallic screw that is used for many clothes washers. Sold individually.
This screw is less than an inch long. It is a metallic screw that is used for many clothes washers. Sold individually.
Installation Instructions
Allen from North Little Rock, AR
One of the plastic hinge pins brroke
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated.
This screw is sold individually.
This screw is sold individually.
Installation Instructions
Tana from ANAMOOSE, ND
Safety agitation switch quit
My son-in-law watched the video on the website and fixed it just fine.
This screw is sold individually.
This screw is sold individually.
Installation Instructions
Quail Valley from Clive, IA
Glass broken on outside oven door
Checked to see that I had all the parts I needed.
Installed bottom door trim then side trim pieces.
Do not tighten screws. Install door handle with top
trim attached over glass. Tighten screws just snug
all around.
Installed bottom door trim then side trim pieces.
Do not tighten screws. Install door handle with top
trim attached over glass. Tighten screws just snug
all around.
This screw is sold individually.
This screw is sold individually.
Installation Instructions
Pamelia from LA CROSSE, VA
Our washer was purchased 1/6/2006 and it started banging and walking out of its place when the washer started into the spin cycle. This would occur no matter the size of the load.
We followed the instructions show on the video. However, our model was assembled slightly different. We had to remove the screws from both sides of the side panels so that we could remove the tub from inside of the machine. Also our model only has one belt not two.
Over all it was easy considering my husband and I had never attempte ... Read more d to repair a washer. Once we got it back together it when back to working like it had never been broken!
We would have never been able to repair our washer without the video that your site provided... thanks so much!!??
Sure wish the manufactures would consider making the older models again as lots of us are not happy with the new modules being manufactured presently!
Over all it was easy considering my husband and I had never attempte ... Read more d to repair a washer. Once we got it back together it when back to working like it had never been broken!
We would have never been able to repair our washer without the video that your site provided... thanks so much!!??
Sure wish the manufactures would consider making the older models again as lots of us are not happy with the new modules being manufactured presently!
Read less