ZISS420DXCSS General Electric Refrigerator - Instructions

1. Remove outside panel (snaps off)
2. Remove Control panel 4 screws
3. Remove Solenoid by taking out 2 bottom screws
4. Remove solenoid weight from crank lever
5. Place new solenoid weight from crank lever
6. Insert weight in solenoid
7. Place back 2 bottom screws solenoid
8. Place back Control panel s ... Read more crews
9. Snap back into place outside panel

Followed the online video. Unplugged refrigerator, removed trim piece, lifted control board cover, removed 4 screws retaining circuit control board and removed the 3 connectors from the control board. Located flapper and removed by using small flat tip to take tension off flapper connectors. Helper held flash light to illuminate flappe ... Read more r connectors. Reversed procedure. New flapper seals well and cured problems. Circuit board was a bit different than one in video, but still had the 3 connectors. Marked each connector with grease pencil at top edge to ensure correct reconnection. Should note how wires are threaded around circuit board to ensure they are tucked back in correctly in reassembly. Remove trim piece carefully. I broke 2 of the 8 plastic pins that hold trim on. May be due to age of unit as they were brittle. 6 pins still hold trim piece flush.

- With a plastic thin putty knife remove the trim panel around the water dispenser. There are plastic clips along each side that just need to be slid inward slightly to release the trim. The thin plastic putty knife worked great for this.
- Remove the electronic panel by pushing the top of the panel down slightly to pull out at the ... Read more top. The bottom will then come out easily. Remove all electrical connections so the board can be detached completely.
- Unscrew the four screws at the corner of the Dispenser Housing Shield. Before removing, note the position of the wire runs for re-installation.
- Take some pictures of how the old Ice Funnel is attached then remove it and reinstall the new Funnel.
- Make sure wires are in their proper place before screwing the Dispenser Housing Shield back in place with the four screws.
- Connect wires to back of electrical panel and angle the panel into the proper place at the bottom and then pull down slightly to go in the top.
- Reattach the trim by gently pressing the plastic tabs into each slot.

Fairly simple fix. You must first uplug refrigerator, then take off the inside freeze door panel, approx. 25 screws. Then you must take out the trap door assembly approx. 6 six screws. Pop off the LED panel, requires the use of a flat blade screw driver to pop it off. Remove solenold by removing 3 screws, replace with new solenold.

I removed the top vent and unplugged the ice machine ,took the back cover off the freezer.Removed the old fan which was pretty easy(unplugged it after I took the housing out for easy access) I plugged the new fan in and put everything back in the order I took off, and yada yada yada we have cooling.

Unscrewed old cartridge, ordered new cartridge, installed new cartridge by following very simple instructions. Took only one day for part to arrive from PartSelect although I paid for cheapest shipping, which was "ground." I was amazed!

replace a new blub

I just followed the instructions on the video and it was exactly as they said......no surprises.

Remove control panel.
Remove four screw in control panel bracket.
Remove to bottom screws at bottom of solinid loose top screw.
Replace all screws.

I removed the door cover plate and disconnected the circuit board, then four screws. The part was corroded in place. Upon removing three screws and cleaning the surface, the new part was an exact fit, replaced it and everything works like new.

Pop off the control board for the ice selector/water. Remove power / signal connections. remove four phillips screws, Remove plastic hopper. Pop off Ice door gasket, pop in new one and put back together. If you fridge was sounding like it was speeding up and slowing down, this will correct this problem as well.

I only had to remove the old filter and install the new one - all by hand. I then ran about 1 to 1and1/2 gallons of water through the filter to clear it.
A WORD OF CAUTION - HOLD YOUR GLASS CLOSE TO THE WATER DISPENSER FOR THE INITIAL FILLING - IT WILL SPIT UNTIL THE AIR IS PURGED FROM THE SYSTEM!!!
An extremely easy repair.

Replaced rusted solenoid.

Popped front button panel off from the bottom using flat head screwdriver; Removed 4 screws holding electronics board and disconnected wires. Unscrewed 3 phillips head screws on old solenoid and replaced with new part. Reconnected wires to board, screwed back in, and pushed panel back into to place.
... Read more />
Thumbs up to PartSelect - fast, straightforward service and fast delivery.

repair was easy, just removed control panel and removed screws from solenoid, switched out with new, was done in minutes

I followed they instructions from the other "do it your selfers" but only replaced the solenoid. This was the cause. Rust was keeping solenoid plunger from moving and this held the flapper door open. Very easy to repair!