YKESS907SS05 KitchenAid Range - Instructions

First we watched a YouTube on how to replace the thermostat. It was easy to turn off the circuit breaker. It was a little tricky to pull the range away from the wall and then we were able to unplug. Because our range is a dual fuel model, the back had a lot more screws to remove to get to the thermostat because there were covers over a ... Read more lot of wires and the gas line I presume. However, we did get off the 12 or so screws with a regular screw driver. We easily located the thermostat and quickly realized that the two screws holding the thermostat in place were neither flat head nor phillips. We were able to remove one of them and merely twisted it sideways, installed the new thermostat with one screw and attached the wires. When we flipped the circuit breaker and plugged in the over, Voila, it worked. The hardest part was getting all the covers off the back. I hope it doesn't happen again because this was an expensive replacement part.

Installed a new thermostat and noticed the convection heating element wire had burned in two. Ordered new element and installed. Oven is currently working properly again.

My story isn't so much about the repair but the fine service from part select. My 1st order was lost at delivery at our house. Part select quickly corrected the mishap with no issues. This kind of service is much appreciated.

Unwrapped the package, plugged the probe into the oven, stuck the other end into the chicken.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol ... Read more oring refer handles. Thank you

turned breaker switch off. unscrewed the oven from the cabinet. lifted the oven out of the cabinet (heavy & awkward, needed an extra pair of hands). removed back panel. replaced fuse. reassembled everything. this is the second time i've had to replace the thermo fuse (oven blows the fuse when set to clean). first time i replaced the fuse ... Read more it took about two hours. second time it about an hour.

Removed four screws lowered element down and removed four wires being very careful, wires can slip back into the hole. Pull wires out of hole. Reattach new element and screw back in place.

Removed wall oven from wall. Removed back cover. Unscrewed thermastat and removed old thermastat. Screwed in new thermastat and put back together.

Removed retainer screw and retainer. Removed old gasket. Installed new gasket, retainer, and retainer screw. Very simple job.

I turned off the power from the circuit breaker. I then removed the doors and the trim package from around the oven. I slid out the oven and had my husband help me lower it to the floor. I removed the back covering and then removed the wires connected to the old thermostat. I unscrewed the old thermostat and replaced it with the new ther ... Read more mostat. Did everything in reverse and it seems to be working very well. It took about 30 minutes total. Some sites suggested that a fuse needed to be adjusted/replaced. In this kitchen-aid double oven and I'm assuming whirlpools as well, the thermostat/fuse is one piece located on the back of the unit. It was very simple. The piece cost $47. Such a great investment of time and money. I had the piece in 2 days, without paying extra postage.

We have double wall ovens and each one only had a single oven rack in it. After 3+ years, I was tired of dealing with the issue so I ordered two new racks from PartSelect. They came quickly and fit perfectly. All I had to do was open the box, remove the rack and slide it into the oven. No muss, no fuss. Why didn't I do this years ago ... Read more ??

Similar to another customer, the racks were not removed before self-cleaning. The issue was that I AM THE HUSBAND and I admit that I did it. Ooops. Great price and if I do it again, I will go back to parts select to get a replacement.

screwed in the new oven light

I was not able to order just the glass, so I ordered the exterior door assembly. The door assembly is held in place by 5screws. 2 on top, 3 along the bottom. A very easy project!

unscrewed the top glass protector off and took the old bulb out and put the new bulb in. very easy - less than 5 minutes.