YG209KW Magic Chef Dryer - Instructions

I pulled out the broken lint filter and put the new one back in, real easy. I am so happy with the prompt delivery I got from PartsSelect.com. I ordered on a Monday and and it was delivered on a Wednesday

First went and got a beer.
Looked at the dryer.
Drank my beer.
Went and got one more, due to long job.
Looked at dryer again.
Opened the door.
Had to get one more beer.
Removed filter.
Got one more cold one.
Put new filter in.
Got one more beer.
Closed door.
Finished!

The door had always opened with the wrong swing and it wasn't til I needed to repair this that I noticed you could change the swing. I changed the swing of the door and then noticed that the clip was included on both sides so i did not need to repair the catch. I still have the part so when it breaks again, I can just pop it in.

I slid in the new one

Parts Select made it extremely easy to order parts from their site. Parts came in a timely manner and very reasonable priced. Thanks to Parts Select! Door Seal just needed to be removed and replaced by pushing into little slot openings.

It was easy - I had my 12yr old daughter do it. The old door seal was completely removed, then you placed the new seal in the apropriate knoches that are on the door of the dryer. The lint filter just had to be placed in the vent. - Done.

1. Removed wires to switch
2. Lifted top panel of Dryer with a screw driver
3. removed two inside screws holding the from panel against the drum.
4. Dropped front panel on the floor and removed door switch.
5. While the door was out, I removed the lint panel attached to the door - two screws.
6. Cleaned the door p ... Read more anel with a vaccum cleaner
7. replaced lint panel onto door with two screws
8. replaced door switch to the front panel
9. placed front panel on to the from of dryer with two screws.
10. Connected wires onto the door switch.
11. Closed top dryer panel and them pressed hard to catch on to metal clips.
12. Attached Dryer cable to electrical outlet
13. Trurned Dryer on and open door as it tumbled to confirm it would stop.
14. Done

Opened the top by popping the two fasteners holding it down. Did this with a screw driver. Took two screws out of the front holding collector in place and two screws out holding the front to the two other sides. Put front of dryer down on the floor. Removed old collector and used all other existing material from old collector to fin ... Read more ish job. Wife could not believe how quick this was. Put back together was a snap too.

I just inserted the door catch, which by the way fit in perfectly. Thanks. Took 5 seconds to repair.

used a flat blade screw driver to open top up(like a car hood) then removed two screws that held the front panel on. Two more screws held the lint colector part in place. The only problem that I had was that I had to use Elmers white glue to hold the gasket that ran around the lint colector in place.Just a little dab, not enough to soak i ... Read more t.When I took the part out there was about a volleyball's worth of lint in the fan blower. Ordered the part and 2 or three days later I had it. If I need another part I will be back...

First I removed the 2 screws located on front panel securing dust collector in place, then I removed the two screws on the side of the dryer that secure the front panel. I also "popped" the top
of the dryer from the front panel. The front of the panel was then detached from the dryer. I thenpulled the gasket away from the collect ... Read more or, removed the old one and installed the new collector. Part of the kit also contained a new gasket to the exhaust duct, I merely removed the old gasket and installed the new one.. All this was notas hard asit sounds. The diagram from PartsSelect site helped

I inserted the clip

After reading the comments of on-line customers, I realized the dryer opens like the hood of a car and then you pull the front of the dryer door off in order to get to the two screws holding the old lint duct housing unit. Putting the new part on was easier, but I would have appreciated a detailed picture along with the written instructi ... Read more ons. Thank you for your quick delivery. Kathleen Yosso

First I removed the screws that held the part in place, but this proved to be the hardest part for me. I had to find the right kind of screw driver . It was not a slotted or Phillips. It was more star shaped. Once I had the right tool, the rest was pretty easy.
I then opened the top of the dryer to be able to lay the front on th ... Read more e floor. There were wires connected to the front, however, so I had to remove the part that the wires were connected to by slipping it out of the bracket that held it in place. Once the front panel was on the floor, I simply lifted the old part out and placed the new part in. I closed the front, replacing the part with wires back into the bracket, locked the top down tight, replaced the screws, and I was finished.

It was supper easy. I was able to order the correct part from the detailed description you provided. I just opened it and slid it into the slot for a perfect fit.

I wish I had done it sooner. My filter had holes in it for some time.