YFW450SSM1WW General Electric Washer - Instructions

Remove the front coverfrom the machine. This is done by removing the 3 screws at the bottom of the panel. The panel then drops down and pulls straight off. The pump is located on the front right wall of the of the machine. You will notice a 2-3 inch diamete threaded cap on the right side of the front wall of the machine. This is the f ... Read more ront of the pump and access to the filter. Place a large bucket under this cap and slowly loosen the cap. All of the water remaining in the machine will begin to drain (this could be a lot of water. Do not remove the cap completely so that you can quickly stop the flow of water if needed). Once all water is drained from the appliance, Disconnect the two hoses from the pump using a pair of pliers to looses the presure clamps, sliding the clamps back an then pulling off the hoses (be careful of any remaining water in the hoses). Then remove the two screws from the rear base of the pump that secure it to the bottom floor panel of the washer. Slide the pump slightly to the rear to free it from the fittings on the front wall of the machine and the lift the pump up. At this point, firmly pull out the wiring harness plugged into the top right side of the pump. Install the new pump by plugging in the wiring harness and resecuring the pump. Plug in the machine and run on the rinse and spin cycle to test.

I took the two drain hoses off with the pliers then only two screws that holds the pump. After that the two hot wires which are black and white. But remember to unplug you're washer since the pump is not grounded you don't want to risk being shocked. Hope thi helps. Plus i saved around 250.00 by repairing myself.

~Unplugged
~Removed front bottom and rear center panel
~Removed broken dampers. Varying difficulty; other components in the way. Used socket to help push pin out with screwdriver and pliers to help remove the pin.
~Installed New Dampers: Used Small (6") crescent wrench for top. Fitting two (2) hands in there, one to h ... Read more old and one to turn was a challenge for all four (4) dampers. Had to extend a couple to wedge to damper in there to hold the arrow hear flush.
Installing the pins in the bottom was somewhat easier than the top. I broke the retaining pin completely off an old pin to align the new damper to the base mounting hole (hard to see in there). Used Pliers, a long screwdriver and rubber mallet.
Note my situation was in a very small room. So small I had to remove the door to the room so that I could pull the washer out to get behind it. The warnings about sharp edges should not be ignored! Long sleeves (chainmail) and steel fish fillet gloves might help!

2 things to note if you’re going to replace this part. First, you definitely need the 6” crescent wrench as noted in the instructions. Second, tape up the flanges of the machine so you don’t cut your arms to pieces on sharp metal edges.

Flipped washer on side
Did repair from bottom
Really easy repair

Did not have to use the new pump filter. The old one finally worked. I probably didn’t screw it in tight enough.

Per ps video. Really easy. Disconnect power, Remove front lower panel, remove Power leads, 2 installation bolts, remove 2 spring clamps on feed/exit hoses,reinstall.

First I locked out the power cord. I pulled the back screws to the top panel off, slid the top panel to the back of the washer, and pulled the top off. opened the washer door, and ran my down where the door switch was. with one hand on the switch, I use the other hand with a philips screw driver to remove the screws on the door switch. Pu ... Read more lled the switch up just enough to remove the electrical plug. Now installation will be the same but start backwards. Plug in the switch, run the switch into the housing. While holding the switch in place with one hand use the other hand to install the two screws. Replace the top panel, remove any lockouts.

Unplug the machine. Remove the door by taking out the 4 screws holding the hinge cover. Then remove the three screws that attach the hinge to the door. You may need to remove the hinge pin (mine fell off as the top of the hinge was broken) Set aside the door. Remove the spring clamp that holds the rubber boot to the washer front. Use ... Read more needle nose pliers to pull the spring away from the boot and use a screw driver to ply it away from the boot around the ring. Gently lift away the left side of the boot to reach the hinge. Remove the four screws that hold the hinge to the washer frame. Reach in and remove the broken hinge.
Insert the new hinge and replace the 4 screws. Replace the rubber boot over the lip of the washer frame. Replace the spring clamp around the rubber boot being careful that the boot seats evenly all the way around the washer door opening. This was the hardest part! Reattach the door. to the hinge and replace the hinge plate over the hinge.

My part came in and my husband was at work so..... I did not want to wait for him to come home to wash my clothes! I installed the motor myself and I was not even the one that took it off! It was so easy to do! Turned the washer on and bingo it was back and going! So glad I can get the parts myself and avoid the middle man and his bill!!! ... Read more Hook up the drain hose with pliers and screw the motor to the frame and that's it!

Removed old pump and replaced. Did not want to wait 2-3 weeks for a repair person

First I removed the excess water by using my shop-vac both inside the machine as well as near the bottom drain valve. After cleaning out that valve (which somehow had accumulated a pair of underwear) it was apparent that the drainage pump motor was no working (loud hum, not spinning). Replacement was easy, folowing instructions found ever ... Read more ywhere on-line. Now the machine is working perfectly again.