XSS25GYPFCFS General Electric Refrigerator - Instructions

Ordered gasket. Laid out gasket near sunlit window untangled and flat on carpet for 24 hours to insure it was pilable and correct shape. Removed the old gasket manually easily without any tools and cleaned the door's seal groove with a paper towel slightly soaked with Simply Green. Installed new gasket starting at the upper corners then ... Read more inserting upper edge by tilting the gasket toward the inside of the door with my fingers. Then installed the lower corners along with the bottom edge. Proceeded installing the side edge working from the set corners inserting the gasket's inner tongue into the door groove with my fingers again tilting the gasket inside the door. Once the gasket was installed, I closed the door and guided my fingers along the gasket to insure the magnetic edge formed a firm seal. This is wear the DIY videos suggested applying petroleum jelly but I did not need it since the gasket was pliable enough. Overall, the effort took 15 minutes because I think laying out the gasket for 24 hours allowed it to settle into its desired form..

Installing the part repaired the fridge and freezer immediately.

Fridge and freezer were not keeping proper temp (freezer would get too cold, fridge too warm), as the cooling coils were icing over and needed manual defrosting; it was not going thru the automatic defrost cycle. Changed out the defrost heating element, thermostat, and two temp sensors, none of that worked. It was this part (main board) t ... Read more hat was the culprit. Eight wire harnesses to undo and re-hook, one was hard to pull out but it came out. Read and follow the anti-static instructions. To make sure, I grounded my hand with a copper bracelet that was grounded with a copper wire to the metal chassis of the fridge. I also drew out a rough sketch of the connections and numbered them all with a black fine tipped felt marker before undoing them. This finally fixed the problem.

I made my wife fix it.

I thought this was my problem as this part causes 90% of the no water issue. However, replacing this part did not fix my problem. I suggest that you test the valve first by disconnecting the water feed from the filter and running the line into a bucket. Once disconnected press the water on the freezer door and see if water comes out.
... Read more >Other than that, this part is easy to install. Take off the plastic in front of the filter, remover the retaining screws. Remove lower cover in back of the refrigerator, Remove 1 screw securing the valve, remove cover where tubes enter the refrigerator. Take off tubes from valve (be sure to note what is inlet and outlet) and feed back into refrigerator. Be sure to save the putty when the new one is installed.

I replaced defrost sets, door gasket but still ice buildup freezer part.

First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.

Pulled out broken drawer and inserted new drawer...just that simple!

It was so darn easy! Took less then 10 minutes to fix. Self explanatory no instructions needed! Very cool!

Easy order, fast delivery, two screws, done.

Knew the switch was bad. Researched on the internet how to fix. Used a steak knife to pop the old one out, changed the contacts to the new switch and popped it back in. It took longer to open the box than it did to replace the switch. And the part arrived 2 days after I ordered it.

+The shelf face has little plastic locator clips that snapped off. the shelf face just comes off with a light lift of these two clips and a slight upward pull then lift up and off. The new one slips on with the top slipping onto the top rail of shelf, then push the bottom tow clips over the bottom rail of the shelf. There you have it smoo ... Read more th as glass.

Unplug the refrigerator. Gently pry old switch out with screw driver. Move wires to connector on new switch with needle nose pliers. Pop it back into the hole. Plug back in. Peek inside to see the lights working.

Took 2 seconds to replace door

remove three bolts, installed the new part and was all done