XSS25GYPECFS General Electric Refrigerator - Instructions

First:
Remove all shelf’s and drawers from fridge inside that were on the way of the water tank
Second:
Pull the fridge from the wall
Turn off the water supply:
Unplugged the power supply
Third:
Remove the cardboard cover at bottom of the fridge on the back for better access to the water pipes
From ... Read more the front remove the toe kick for better access at the water pipes
Disconnected the water pipe at the front left side, use a rag or paper towel to hold the water that may drip ( bigger pipe)
Remove the covers on the top of the water tank inside the fridge
Disconnected the water pipe at the back left side ( smaller pipe)
Unscrew the water tank (two screws)
Pull the water tank out with the water pipes attached
Fourth:
Install the new water tank assembly , make sure the pipes goes on the hole at the right side and reaches the from and back
Connect pipes until the line that shows on the pipes
Screw back the new water tank
Put the protections back on the top
Plug the fridge and open the water supply to make sure there is no water leaks
The water is ready to be use

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new

Needed to remove and replace the door stop. It was held on by tow screws that are about 3 inches from the floor. God a hex driver and small ratchet to hold the hex head. unscrewed the old and replaced the new. I did take a picture with my phone and it showed the two screws.

Clear freezer items in the area of repair as light assembly is in the back of the freezer. Suggest removing shelving in the same area to provide more working space. Utliize a small flashlight to provide interior lighting. Use a stubby phillips screwdriver to remove fastener securing the light cover.
Cover snaps out to remove light bo ... Read more ard assembly. Gently pull to disconnect the electrical connection to the light board. Then pull the light board assembly from the mounting posts securing the light board. Be careful not to snap either posts or the light board.
To install the new light board, I found it easier to connect the electrical source first, then push the light board onto the plastic posts to secure the light board. There are holes in the light board to insure a secure fit. Reinstall the light cover and reinstall the mounting screw. All done in less than 5 minutes!

I got the model # off the fridge, ordered the part online. The part was fairly cheap and was at my house 2 days after I ordered it. It was the exact part and I installed it in about 15 minutes and everyting worked out fine and easy and cheap, under $15 total to fix the issue. All I needed to do was use a flathead screwdriver to "pop" ou ... Read more t the old switch, remove the 2 wires off the wire connection points, put the wires on the new switch and push it back into place. easy. Great place to get exact parts and fast shipping.

I located the light switch at the bottom of the area where the door closes. I just popped it out with a small screwdriver and installed the new switch. A 2 wire connecter and small clip is all there is to it.

Put the new one in--simple!

Really simple... broken light switch easily removed with flat edge screw driver. Once removed unplug and plug new one in and good to go.

I pulled the bulb out to see if it was the bulb, no! I took the switch out, of course with the refer unplugged, and jummped out the wires and the light came on. Ordered my switch and put it in in 10 seconds and then there was light! Thanks again for showing me the light!

Tim in NJ

I just moved the moving parts from the Frame for the humidity level from old to new and all was OK

My father called and asked me if I knew where he could get a new switch light for his refrigerator. I came across your web site and found the part right away. In less than 3 days the part came and my father put it on. He said it was easy and that it was great to have the part come to him instead of having to search all over town. Thanks ... Read more so much for the fast, easy service.

We opened the box, unpacked the drawer, washed and dried it, installed it! No muss, no fuss!

Simply removing parts from the old frame and installing them on the new frame and putting everything back in the refrigerator to include the glass.

Ordered gasket. Laid out gasket near sunlit window untangled and flat on carpet for 24 hours to insure it was pilable and correct shape. Removed the old gasket manually easily without any tools and cleaned the door's seal groove with a paper towel slightly soaked with Simply Green. Installed new gasket starting at the upper corners then ... Read more inserting upper edge by tilting the gasket toward the inside of the door with my fingers. Then installed the lower corners along with the bottom edge. Proceeded installing the side edge working from the set corners inserting the gasket's inner tongue into the door groove with my fingers again tilting the gasket inside the door. Once the gasket was installed, I closed the door and guided my fingers along the gasket to insure the magnetic edge formed a firm seal. This is wear the DIY videos suggested applying petroleum jelly but I did not need it since the gasket was pliable enough. Overall, the effort took 15 minutes because I think laying out the gasket for 24 hours allowed it to settle into its desired form..

It was so much easier than I thought. First we used a hair dryer to loosen everything up. Just pulled off the old on (with our hands) and put the new one on. Then went around the edges and wiggled it into place. There are plastic ridges that if fits into, so it’s important to make sure every part is sealed.