XFE26JSMPFSS General Electric Refrigerator - Instructions

my freezer quit freezing, it would freeze for one day, thaw the next, so I went online, found PARTS SELECT, LOOKED UP MY MODEL #, come to find out it needed three parts to keep my freezer to freeze, first part was a thermistor a small PART took me longer to remove all the covers, and shelving, PULLED THE ... Read more OLD OUT, CUT THE WIERS TO SIZE, AND REINSTALLED, IT WELL! THAT WASN'T ENOUGH THE FREEZER STILL DIDN'T FREEZE IT THOUT IT WAS A COOL WORMING OVEN, HAD TO INSTALL THE THERMISTOR I, SO I DID, TEN MIN, NOW I THOUGHT THAT WAS IT BECAUSE IT STAYED FROZEN FOR A WEAK, HAVE YOU EVER EATEN SOUPY ICE CREAM? SO BACK TO PARTS SELECT, THIS TIME I BOUGHT ONE MORE PT, THE RUN CAPACITOR, FIVE MIN, THAT/S ALL IT TOOK TO INSTALL. I DID NOT KNOW AT THE TIME YOU NEED THE THREE OF THEM TO RUN THE FREEZER ONE TO KEEP THE TEMP., ONE TO KEEP THE FAN RUNNING THE WAY IT SHOULD, AND THE THIRD TO MAKE SURE THE OTHER TWO KEEP RUNNING. NOW I CAN SET IT AT 4- 5 AND. FREEZE.

Very easy and the part was a perfect fit

the meat pan was broken when I unpacked it.
was suppose to be told what to do with the broken draw but haven't heard back yet

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of f ... Read more reezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.

Ordered new shelf. Took a few weeks to come, but it did come, and it was the right part. Simply put where the old shelf was, and Bob's your uncle.

Ordered new shelf and put it in my self

Turned water supply off; pressed dispenser sw to release presure ; cut tubing holding reservoir ; nuit driver to release screw holding reservoir and pulled out ; took outside and used hose nozzle to try to clear; did not clear at first then took weedeater string and disloged something and water flowed freely; turned out had to change waer ... Read more solenoid valve (both) as the one for the water dispener was also plugged which did not show up before.
P.S. Had back flow water thru system before and changes of parts. Water flowed freely.

Two screws out, unplugged wire, snapped out. Plugged in, snapped back in, two screws in.

Removed ice bucket, and unplugged ice maker. Removed light cover. Removed ice maker. Pulled fan blades straight up and removed. Pushed new blades on to motor shaft. Fairly easy .

Replaced Temperature Sensor and now it is getting cold.

The best instructions were several YouTube videos for replacing icemakers on GE french door bottom freezer refrigerators, but none fully described the process. The following difficulties were encountered: (1) Instructions for removing the freezer door showed three screws on each side that needed to be removed; in fact, there was only one ... Read more screw on each side. It was smaller than the three depicted screws and its location was not exactly as shown in the videos. (2) None of the instructions adequately described the process for removing the mounting plate from the nonfunctioning icemaker so it could be attached to the replacement unit. The key was to forcibly pry open the cover over a screw that then needed to be loosened with a screw driver. It seemed that I risked breaking the unit when I tried to slide the tab, but it eventually moved and revealed the screw that was holding the original mounting plate in place. (3) Replacing the freezer door required lining up some metal studs with slots in the undercarriage; you need to get down on the floor to examine how this fits back together. (It might help to take some photos before removing the freezer door.) (4) Replacing the upper drawer was perhaps the trickiest. My first effort resulted in having the rod with gear pinions on each end pop out because some of the tabs holding the gear pinions on each end broke. That meant that I had to order two replacement gear pinions (left and right are identical). Then, as with the freezer door, it was necessary fo slide metal studs on each side into a vertical slot leading to a horizontal slot in order to seat the upper drawer properly. So the whole process took a few weeks; actual work time was perhaps 3-4 hours. This could have been shortened significantly had I taken photos as I disassembled everything and if the procedure for moving the mounting plate had been clearer (or even existing). All in all, though, this is a doable DIY project.

Totally followed the instructions of the video that came with the sensor. Unplugged the the fridge, defrosted the freezer. Cut off the main sensor that usually is the one that goes out. Installed the the new sensor with new wire terminals, crimped them and covered with electrical tape. Fridge works like a charm. Partsselect is excellent. ... Read more Saved me a few hundred dollars versus having a GE Tech come and do it.

I watched the instructional video on this website and did everything that it said. There is no more leak when I use the in door water. Was as easy as it looks in the video and I am very happy!

Repair was made simply and quickly by removing broken parts and replacing with new. No problems

Took cover off, pushed blade on, and replaced cover