- Home
- XAV13PRBWW
- Instructions
XAV13PRBWW Maytag Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
would not drain/slow spin
11 of 16 people
found this instruction helpful.
-
Carlos from Georgetown, TN
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Socket set
i did the repair by the instructions that you had on the web site,and i thank you for all the help you gave me.
Other Parts Used:
Was this helpful?
Thank you for voting!
would'nt wash w/out getting hot
10 of 14 people
found this instruction helpful.
-
Emery from Talladega, AL
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
just took the front off and then took the old motor off and switched over about 2 parts from the old to the new and then put the new part on and then placed the front back on and it was ready to go
Was this helpful?
Thank you for voting!
Loud squeal when spin cycle finished, white powder under washer
8 of 8 people
found this instruction helpful.
-
Kevin from Pooler, GA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Wrench set
Read DIY review from William, Middleton, OH on 01-15-08. Tip on how to relieve spring pressure on brake assembly worked like a dream (3ea 10-24X2 bolts/machine screws). Replaced brake and machine works like new and was an inexpensive fix. Once the shell/housing is off the machine, tub can be turned upside down and the base doesn't need t
... Read more
o be removed. White powder under machine was a plastic wear ring that tells you when your brake rotor needs to be changed. Brake rotor still had lining but was much thinner than replacement part. Note* Use putty knife to push in clips on front to release the top lid section.
Read less
Was this helpful?
Thank you for voting!
One of the two bolts that holds the motor in place broke off and since the bolts are actually embedded in the motor I had to buy the whole motor rather then just a 25 cent bolt.
18 of 38 people
found this instruction helpful.
-
Elmer from Fort Campbell, KY
- Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
First I took the front shield off, then I took the motor off.
Was this helpful?
Thank you for voting!
Washer would fill, but not spin, agitate of drain
8 of 9 people
found this instruction helpful.
-
Mathew from Fort Collins, CO
- Really Easy
- Less than 15 mins
-
Screw drivers
Very simple, Lid cam part was broken, Just need to remove broken plastic lid cam with screwdriver and then snap in place the new piece. Worked like a charm first time. Easy , inexpensive repair to a reliable washing machine. Bill
Was this helpful?
Thank you for voting!
Old agitator broke
9 of 13 people
found this instruction helpful.
-
Johan from Kingsford, MI
- Really Easy
- Less than 15 mins
-
Wrench set
Removed old agitator, and installed new one. Very easy.
Other Parts Used:
Was this helpful?
Thank you for voting!
Auger was broken
7 of 7 people
found this instruction helpful.
-
Charles F from Brooklyn, OH
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Needed a medium extension and a rachet a screw driver and a 13mm socket. I used a short screw driver and inserted in it the softer container and lifted it strait up to get the softner container out of the way. I used the medium extension to reach in the auger and loosen the small bolt holding the auger on the machine. Pulled it up and o
... Read more
ut. Reversed the above procedure and it was set to go. Total time about 8 to 10 minutes. Thank for all the help Kudos to all including Susan W.
Read less
Was this helpful?
Thank you for voting!
No water fill ,close the lid machine does not work
8 of 10 people
found this instruction helpful.
-
Tuong from Sacramento, CA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
just unplug the power , disconnect the wire from lid switch ,slide the lid switch assembly out off the switch housing . Then reverse the action I just did above and the machine work again.
Was this helpful?
Thank you for voting!
slammed lid and broke lid switch
8 of 10 people
found this instruction helpful.
-
Patrick from Little Rock, AR
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
it took a little longer to fix the lid switch becasue the you have to figure out how to install the switch after you takethe old one out. The old one popped out but the new one needs some twisting and pressure. It also is an ackward position to work in on the back of the washer front the front. I think the instructions could have been muc
... Read more
h better by warning the installer to pay attention when you take the old one out. But it worked and we fixed the problem for $22 and four days of waiting for the part.
Read less
Was this helpful?
Thank you for voting!
The washer did not start. The only thing that would work was the fascet switch would add water.
7 of 8 people
found this instruction helpful.
-
Jim from Owosso, MI
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
I opened up the control panel on the back by removing the 4 screws and then used the print that was inside to check where the power went from the power cord. I checked the power at diferent places and determined that I did not have power coming from the lid switch with the door up or down. You could here the switch click when you opened a
... Read more
nd closed the door but aperantly it was not working. After going on your web site and looking at the other posts I realixed that there was a fuse link in the switch that was probably blown. I ordered the switch and it was a simple matter to replace when it arrived. The washer works great once more.
Read less
Was this helpful?
Thank you for voting!
Hose had a split in it
8 of 11 people
found this instruction helpful.
-
Chris from Hoffman Estates, IL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
took off front of washer , took off hose clamp removed old hose . replaced with new hose clamped back on put on front cover ran washer check for any leakes. done and done
Was this helpful?
Thank you for voting!
Washer shut down while filling w/ lid up
7 of 9 people
found this instruction helpful.
-
Peter from Gilbert, AZ
- Really Easy
- 15 - 30 mins
-
Screw drivers
I did a continuity check on the lid switch assembly since it was a) the easist to get to, and b) my wife's descreiption of how rthe washer stopped made me think it had something to do with the lid switch.
I found that all of the contacts were open regardless of the position of the switch, and I also discovered that there was a fuse i ... Read more nside the swithch. I decided to order a replacement part based on the presence of the fuse.
Upon repacling the fuse (a snap in affair), the washer was working again... my wife was impressed and I was happy!
I found that all of the contacts were open regardless of the position of the switch, and I also discovered that there was a fuse i ... Read more nside the swithch. I decided to order a replacement part based on the presence of the fuse.
Upon repacling the fuse (a snap in affair), the washer was working again... my wife was impressed and I was happy!
Read less
Was this helpful?
Thank you for voting!
Leaky hose resulted in damaged Thrust Bearing
8 of 12 people
found this instruction helpful.
-
Steven from Gilbert, AZ
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
After replacing the tub to pump hose, I adjusted the feet on the washer. Apparently, the main pulley sits so low on these washers that it ground into the floor and stripped out the thrust bearing. I ordered the new thrust bearing clip and put it in the evening I received it. The instructions it came with were very helpful and it was si
... Read more
mple to reassemble. Up until the last piece - the retaining clip. The majority of the repair time was spent replacing that clip. If there is a tool that makes the job easier, I didn't have it. I finally got it on with two flathead screwdrivers prying the shaft out while I wedged one corner of the clip in the groove.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
washer was squeeling to a stop
7 of 9 people
found this instruction helpful.
-
paul from newbern, TN
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers, Socket set
first remove drive belt then then remove dust cover on bottom of shaft take 5/16 nut driver to only 4 of the screws off that hold the brake cover on install 4 5/16 screws 1" long in those 4 spots.reomve rest of screws then slowly reomve back out 1" screws to relve spring pressure from brake pad.install all new parts from partsselect.com
... Read more
then install other part taken off in oreder and make your wife very happy
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washing Machine Would Not Start Up
6 of 7 people
found this instruction helpful.
-
JOSEPH from MERRICK, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I removed three small bolts on the back of top panel unpluged electric plug on lid switch popped out old switch popped in new plugged in switch put top back on with the three small bolts. The wife was back in business. Easy as 1 2 3
Was this helpful?
Thank you for voting!