WWSS2614SP0 Frigidaire Refrigerator - Instructions

Consult the exploded view of the Ice Container on this site. A likely cause the end plate (17) is worn. This plate connects the rotating corkscrew to the final plastic worm that pushes the ice into the crusher and thence to your waiting glass. The worm alone will not do the trick. To replace this plate, you need to take out all o ... Read more f the screws you can see, including the one that holds the spring for the crusher select bar.. First, the front cover, then the plate, and finally, locking ring from the worm and the black housing for the crusher. Now you can remove the whole worm assembly. Using a cloth or rubber insulator to protect it, unscrew the end screw and slide off the crusher teeth. Store on the table as a unit to facilitate re-assembly. Slide off the old bar and worm, put them back, and re-assemble. Takes a little dexterity to get the crusher select bar back, but not hard. Easy job.

Twisted replacement bulb into place easily. Let there be light!

Removed screws holding unit and removed unit. Removed switch from connectors in unit. Replaced unit without switch. On day switch arrived (delivery was prompt) my wife replaced switch by attaching the two connectors and slipping into unit without having to remove entire unit. How easy was that!!!

The parts arrived much quicker than expected. The parts were exact matches and they snapped into place within minutes.

I ordered a new shelf and I put in, less than minute

The service manual diagram shows the 149 complete fan shroud in a vertical (upright) position. Misleading! Of course.
The actual mounting of the lay in fan shroud fully assembled is in the horizontal position laying in a tray area just above the evaporator coil cage assembly. The entire shroud assembly can be installed incorrectly by ... Read more the diagram and will still fit. BUT... no cold air will flow or be forced into the ice maker vent nor the refrigerator vent. I found this out the hard way by trial & error.
If the drawing had shown it in the horizontal position for both removal and reinstallation... it would have saved a lot of time and headaches. Also, the diagram does not show the (2) plastic angle supports on the shroud, another scratch your head event. Parts included on drawing... 149, 5, 8, 9, 13, 14 on CTFFHS2611PF4 diagram page of service manual.
ALSO, the (4) lower cabinet plate screws have to be removed, and the first left hand screw counting up to allow the next upper panel to swing out enough to lay the shroud in correctly (horizontal) on top of the evaporator coil cage. BOTTOM LINE... THE AIR FLOW HAS TO BE UP IN ORDER TO WORK PROPERLY.

Remove the bottom freezer drawer. Remove back metal evaporator panel. Wire in new defrost terminationT-stat. Reassemble evap panel. Good to go.

Replaced the Triple Water Valve

Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.

None of this was obvious - an online tip from another member was invaluable ... Read more .

The repair was just as easy as ordering the part which arrived on day three after I ordered it! I had already cleaned up the broken glass insert, so all I had to do was unpack and lay the new shelf in. Took less than a minute!

Looked at video on how to remove and reinstall support and followed the instruct ions

This was a replacement part, a simple snap in. What really impressed me was the PartSelect web site and the ease of locating the part and making sure it was the right one. Finally, the price beat out all the others. Since this tray looked like others on the same unit, I needed the details, the different view angles and dimensions to make ... Read more sure it was correct. No other web site was even close in ease of use or in providing such details. I know I won't waste my time at PartSelect and I've always gotten the right part at the best price.

So simple! I just slid the drawer out of the old frame, inserted it in the new one, and added the glass cover.

Turn off ice maker
Slide wire harness shield off connector
Disconnected harness
Loosened 2 wall screws
Remove old ice maker
Installed new one reversing process

From discussions with friends, I determined the problem might be easy to fix. The fridge made a lot of noise, but the compressor DID come on, and inside the freezer was cold, but the main fridge was warming.

After unplugging the fridge, I removed the fan assembly in the freezer (there were about 4 nuts and a couple of plugs to ... Read more uncouple.

I could see right away the fan blades has broken off, but the motor looked good. The new new fan pushed easily onto the shift and fit perfectly in the housing.

I reinstalled the fan assembly, plugged in the fridge, and right away heard the new fan come on - very quietly. What was a roar became a whisper and the fridge was down to 38 degrees with a few hours.