WWSS2614SP0 Frigidaire Refrigerator - Instructions

I went on line and presto! Ordered the part! It came in the mail just two days later and I popped it into place! Thank you for such service!

Ordered a new shelf which arrived very fast. Installed in no time at all as it just slides in and rests on brackets. No tools needed and the new part looks just like the original.

The parts supplied were made to fit. The hardest part was getting the original broken tabs out of the internal walls of the fridge with out damaging the internal insulation. I punched the center locking pin through completely, dug out the broken tabs and then reached into the hole with a dental pick and pulled out the center pin. The new ... Read more parts fit perfectly and with a plastic mallet, tapped the new locking pin into place.

I removed the back cover and removed the clip holding the compressor- run capacitor and start relay. I replaced these 2 components and clean the dust from the frig., and from the bottom of the floor. I replaced the back cover ; Loss about $300 worth of meat when when the frig. failed. Then I thought that, during these turbulent times, ... Read more there are many which don't have a refrigerator or any meat to place in it, The refrigerator is "running" normal again.

Remove the screws that hold the old valve to the side of the refrigerator. Next, detach each plastic tube and attach that tube to the same place on the new valve, and repeat (there are many valves). Afterward, I realized that many of the plastic tubes had become brittle and had mineral deposits, so I bought additional tubing for ice make ... Read more rs and replaced each tube, one at a time.

Pulling the old seal was the easy part. The problem became dificult when I opened the seal package. Either Part Select or UPS had folded the seal in half. Witch caused the wire inside the seal to become crimped up. I used a pair of pliers "carefully" to straighten the wire as best I could. Luckly it worked, after pressing it firmly all th ... Read more e way aroud about 5 or 6 times. I'll still keep an eye on it for the next couple of weeks.

I had removed the housing that the drum was in and taken the screws out to get to the broken drum. I removed it there was a set of 6 blades that crushed the ice that had to go back on the same order when I removed these I put them on a piece of wire in the order they came off (so I would get them back I the correct order). Then I reversed ... Read more the order and reassembled it in the opposite direction . It was fairly easy to do. I'm a 68 year old disabled woman so if I could do it I'm sure you could to. Good luck. It cost me $14.00 if I had bought the whole assembly it would have been $150.00. So it was well worth my time and effort.

We followed the video instructions and it went fairly smooth. After turning off the water at the street we found that the faucet at the wall had it's own "on/off" valve. When finished, we turned on the power and heard the gears going through their revolutions, but no ice was made. We waited 24 hours and still no ice. I removed the cover o ... Read more n the ice maker and adjusted the amount of water to see if that was malfunctioning. Still no ice was created. Waited another 24 hours - nothing. Waited another 24 hours (the site said that sometimes the ice maker would take time to reset itself) - nothing. Then on the fourth day after changing out the triple water valve we heard water being dispensed and later that day it put out the first ice in weeks. Another hour later another batch of ice cubes were ready and deposited into the bin. Since that time, we have had a full bin. I moved the set screw back to it's original setting because a little too much water was being delivered. The cubes weren't separating to individual cubes. That cleared up the problem. This was easily completed - we recommend others do their own work. Just be patient for the system to reset itself.

Took the ice storage bin out. Took the unit apart,and disamble the augar unit. Ordered parts from manufacture, which arrived in two days. As soon as I got the parts, I reassambled it. Work perfect. Good job!

lifted out the damaged bins and snapped in the new ones.

put the new ones

I followed the video tutorial published here. The step I altered was setting the shrink wrap; I did not have a heat gun to safely shrink it, so I folded it tightly onto itself and wrapped it in electrical tape. No more frost buildup.

Unscrew 4 screws . Remove broken basket hangers. Install new basketo hangers. Screw in 4 retaining screws...

The most difficult task for me was getting old gasket out. I did call for repair help. The service person was most helpful. After almost giving up, one more tug and the gasket started coming out. Next step was cleaning the area. Aligning the gasket correctly made installation easier. I realized right away that I needed to start in a c ... Read more orner. The gasket went in without a hitch. My freezer is like new again. Next installment will be the refrigerator.

This is the second time I've had to replace the crisper cover, so I had that step mastered. As before, I took the glass from broken crisper cover and dropped it into new cover in seconds. Had to use a screwdriver to pry old crisper supports from the walls of the fridge. This was the only hassle. Popped new supports in, replaced crisper co ... Read more vers, and slid crisper drawers back into place. From now on, I'll have to be more careful about how much weight I put into crispers.