WTW8240YW0 Whirlpool Washer - Instructions

Watched a video on the internet.

Removed a cap in the center of the tub basket which has a bolt that needs removed I believe it's a 9/16 after I removed the bolt I then removed the center of the bottom of the basket assembly which then allowed me to get to the basket hub that needed replaced it was a little dirty and I couldn't get it out so I sprayed a little penitratin ... Read more g oil on it let it sit a little then I was able to remove the hub and install the new one then I put it all back together and the washer is working great

Went on u tube saw different video to How disassemble the top to have access to the rod. Changing one by one those rod I was in need of my wife to hold the cover while I was changing the rod.... order for suspension rod kit. Reassemble the top by sliding the cover and to snap. Screw back the panel. And it solve the problem. My wife was r ... Read more eally happy so me. It can be done by anybody but first go on the internet to get a idea.

3rd time replacing this part. The plastic grooves against the metal get wore down. Only 20$ to repair ! Take off the 3/8 bolt - center pops out. Remove screws pop out old piece and tighten new piece each side evenly.

replaced the drain pump which took about 10 minutes. removed 3 screws, unplug elec. wire, remove 2 water hoses, put back together in reverse.

Remove agitator and replace hub. I also recommend replacing the Suspension too. I could tell the hub was bad the piece of metal washer on the bottom was gone. The suspension lost a lot of its stiffing

Followed video from you tube. Man made it look very easy. Not! Hole that lock has to come through in back was very tricky. Also, DO NOT THROW OUT OLD PART UNTIL NEW ONE IS INSTALLED. The reason for that is there is a CLIP at the end of the old part that is needed to attach new part to wire section in control panel. NO WHERE is it m ... Read more entioned at you got the clip from the old part. Luckily we saved it. Without that clip, you are screwed.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

two small compression clamps hold the hoses in place. these are very simple to remove, however to reinstall the new hoses you should unscrew the pumps with a nut driver, secure the hoses with the clamps, and then screw the pump back to the bottom of the drum. oh yeah make sure to put the back plate back on the machine

Dismantled washer lid to install new locking mechanism.

watch utube instruction.easy repair

First replaced four basket spring supports. Next tried Basket hub assembly ( which showed wear, but not total solution). Next replaced the rotation sensor that's on the stator. That finalized the issue.

Replaced water inlet valve. Parts select video was incorrect for my unit. There are no spring clips to be released using a putty knife. Rather remove the two screws in the back of the top, pull the top forward and up to get at hose connections to the valve. Hint, place a towel under the valve connections because after removed from the val ... Read more ve, the hoses will leak to the floor. I propped the top up with a stick. All the other stuff in the video is good. Unplug and turn water off, remove connectors from old valve etc. . I also removed the protective plate over the cabled that runs between the washer and the control panel located on the back of the washer. The will make the sliding of the top forward easier. Only one screw involved.

Pretty easy! Just follow this link on how to fix the problem:

https://www.youtube.com/watch?v=_-Hg8rLGiKQ

The hardest part on fixing this is trying to move the washer out of its place so I can tilt it to see underneath the washer where the repair would be.

I followed the instructions, however I did not have a spot to hold the bar temporarily, so I drilled a hole in the corner frame to hook them in at the front of the machine. All else was easy and according to the video.

Machine works great now.