WTW6200SW1 Whirlpool Washer - Instructions

It was not easy but I dit my sell

Our washer wasn't really working, we called a tech to diagnose our problem, he charged us $35 to let us know that we had a suspension problem, he promised to call us back next day with the estimate for the repair, he never did. So I decide to search, I found a video showing exactly how to do it, it was a very easy, and simple process tha ... Read more t I decide to order the parts my self. The parts were delivered to my door in 24hrs. I installed the parts in less than 45 min, and now our washer is working like new again!!!

Thanks guys.

Removed the fabric softner at the top of the agitator (needed a screw driver to pry it loose) and reached in to grab the barrier with my hand and pulled it out, very simple to do.When I put the new one in I put some liquid soap on the gasket and it snapped right into place.Very easy to do, all is well now, thanks Part Select.

Rubber O ring around the Inner Cap was rotted and busted through. Replaced with new Inner Cap Seal. Easy as pie!

Just had to remove cap on agitator and replace new rubber seal.

1) I cleaned out the top cavity of the agitator. 2) The new softener assembly just snaps in place when seated all the way down. Easy.

need to get washer turned on side where you can work underneath the machine. This job is alot easy if you get where you can see good and have plenty of room to work. You have to unhoook the wire from the old pump and then take the two mounting screws off from there you unhook each hose by squeezing clamp together and sliding backwards awa ... Read more y from pump. A pair of needle nose pliers can make this process easier if the clamps are turned in an hard to get to position. You mount the new pump the same way as taking off the damaged pump. Take a screwdriver to help you slide the clamps up onto the new pump makeing sure the sleeves are completely over the new pump fittings and the clamps are slid up evenly, so you want have any leaks. Then replaces wiring harness and mounting screws.

Easy repair. Went to You Tube and saw PartSelect video. The best instructions...should make a link from parts page to video of install. Also replaced Heat element on Dryer. Watched video first.

Pulled washer from back of wall and disconnected power source. I removed three screws in back that houses the ol motor control board. Also, I had to pull the front control knob off so that I could lift the cover to expose control board. I took several pictures of the motor control board before unplugging the wires just in case I forgot ... Read more where the wires needed to go. Very simple process and had machine working within 15 minutes.

went well but alas the problem still exists.

put machine on side pushed old rods out to top installed new ones. runs like new. tried to ask mechanics or stores nobody would help with info, they all want to send mechanics with 80$ just to get here. it was easy to do. thanks

First off always remember to empty all pockets, coins etc ruin pumps.shut off water supply, unhooked water lines and drain into pan.tilted machine forward so i could work on pump which is located lower left. drain pan under pump area, removed 2 rubber water hose's 3 5/16 screws with nut driver. Very carefully un clip rear of housing and r ... Read more emoved wire harness. installed new pump

All went good until installing the rollers. I put a rubber ban around them to hold them in place so I could put the upper and the lower parts together. I had a string tied to the rubber ban so all I had to do is pull the rubber ban out and the rollers stayed in place.

Well i watched a video on youtube that demonstrated the repair, and it seemed easy enough, so i ordered the parts which arrived quickly enough that we avoided a trip to the laundry mat, very cool! So i did just what they said to do, unplug machine, tape down the lid, use a putty knife to pop the retaining springs in front. I used a long s ... Read more crewdriver to hold up rod on top and then rotate the ball around and let the rod fall through, them i used a yard stick to pop out cup on bottom. I did have assistance holding the drum back so i could see, Then i reversed the process with a new rod. The only reason it took 30 min was i did not put the cups under the balls on top, because it didnt have them in the first place, i decided to put them in after then reading the instructions. The machine runs like new, and my wife is very happy!!

Unplug washer. Use scraper to depress spring steel catches under top cover of cabinet. Raise and support cover. Remove lock mechanism from cover using nut driver and remove switch and cable from spring tension clips. The last cable stay is zip tie/plug; pry it from hole in cover. Don't worry about saving this cable stay as the new switch ... Read more has one pre installed. Before lowering cover place an object such as a rolled up towel over the cabinet spring catches to prevent engagement. Then lower cover. Locate two screw on back of control panel and remove with nut driver. Just below control panel on back side of cabinet is a single screw securing a small cover plate. Remove screw and plate. Lift control panel and turn it over. Locate plug for the latch switch and disconnect it. Then set control panel back in place. Raise and support top of washer again and pull faulty switch and cable assembly from washer. Attach new switch assembly to top cover and place cable into spring clip and insert plastic cable stay into hole. Route the connector through the opening the faulty one was pulled from. You may now close the top of the washer. Lift and turn over control panel connect new switch plug and set control panel back in place. Replace screws on back of panel and the small cover and screw. Plug washer power cord in and you should be done.