WTW4300SW0 Whirlpool Washer - Instructions

Research showed it was the transmission and the actuator . Parts were super easy to install and it solved the issue 100%

PS - I put some light lithium grease on the transmission and it’s quieter than it was when new

Followed detailed instructions which were supplied with the parts. It was easy and my machine is working great with no issues. Also I just didn’t get the main drive pulley, all new parts came for the bottom end, great service and excellent parts.

W10721967 Splutch Cam Kit

Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.

When I took off the 13mm ... Read more nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.

Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.

Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.

Remove the center cover with a screwdriver then loosen the 7/16 bolt with an impact driver socket ccw to remove completely biggest issue is removing bottom cover tried pick tools only thing that was succesful was some dawn dishsoap on the center bolt area to loosen enough to lift up the cover replace the hub part that had worn spline groo ... Read more ves remember to use blue loctite on the 7/16 bolt before re-installing cw to tighten bolt

screw driver and a rachet and socket took it off and put the new one on . no problem follow the direction that comes with it .

First, this is the second time the transmission actuator went bad. The first-time washer was still under warrenty and I watched the tech replace it. This time warranty has expired and I'm mechanically inclined, so I ordered the part. Replacing was easy, unplug, tip washer up so you can get under it, remove plastic guard (two hex nuts) and ... Read more remove actuator by removing two screws. Reverse procedure to install new actuator. The only caution I will say is when tipping washer if you have a wall to lean it against, perfect, just put something under it for saftey so it can't fall on you.

Watch video on the site and the insulation will be easy and take about 30 min.

I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!

Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.

Getting to the actual hub is a bit difficult as it involves removing the accetuator and takes some time and patience, but when I tried to replace with a new hub, I found that the screws were stripped, so PartSelect walked me through the ordering process and helped me choose the exact size screws that I needed. Parts came quickly...I alre ... Read more ady had the hub waiting to be secured and the screws tightened easily. (We had tried using a similar size, but you REALLY need the whirlpool screws that go in there) No more spinning problems, and the machine is not jumping around anymore. Works just like before. This particular machine has to have this part replaced at least twice a year (luckily it's cheap),but saves us from having to buy a whole new machine. My son also told me that since I replace the part so often, best to replace the screws every other time as well.

Pop center cover off wash plate. Remove bolt. Lift off washplate. Slide retainer off with screwdriver and hammer. Slide new retainer on. Replace washplate.

Royal pain getting the wash plate off. I'm 6 foot 215 lbs with muscular arms( beer belly too) and I could not get it to come off. Put hay bail twine around the edge and pulled up so hard the entire machine came off the ground. Luckily I am married. Yep I pulled one end of the string and her the other and it flew off. Part select was $10 c ... Read more heaper than whirlpool and was a perfect match. I might order another to have because like stated earlier I'm married. She is married to me and the washer and dryer.

Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.

Tip the washer on its back remove the agitator install new one under 15 minutes

remove basket and replace drive hub kit