- Home
- WSSE5210B2CC
- Instructions
WSSE5210B2CC General Electric Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Agitator Not Working
1 person
found this instruction helpful.
-
Rob from Wytheville, VA
- Really Easy
- Less than 15 mins
-
Wrench (Adjustable)
I removed the center piece in the washer by pulling up on it, removed the retaining bolt and the agitator coupling.
Installation reverse of removal...no problems. The spline on the inside of the agitator coupling was worn out.
I never would have though about it until I searched the problem on line. I had already deci ... Read more ded that I would have to buy a new washer (again)...I had a pressure switch problem about 6 months ago.
PartSelect is great...I ordered the parts for both problems from them and I have kept my old washer alive.
Installation reverse of removal...no problems. The spline on the inside of the agitator coupling was worn out.
I never would have though about it until I searched the problem on line. I had already deci ... Read more ded that I would have to buy a new washer (again)...I had a pressure switch problem about 6 months ago.
PartSelect is great...I ordered the parts for both problems from them and I have kept my old washer alive.
Read less
Was this helpful?
Thank you for voting!
Agitator did not rotate
1 person
found this instruction helpful.
-
Doug from Puyallup, WA
- Really Easy
- Less than 15 mins
-
Socket set
1. Remove agitator with a quick upward jolt.
2. Remove bolt with ratchet or wrench.
3. Remove agitator coupling.
4. Install new coupling, tighten new bolt and slide agitator down until it latches after aligning appropriately.
2. Remove bolt with ratchet or wrench.
3. Remove agitator coupling.
4. Install new coupling, tighten new bolt and slide agitator down until it latches after aligning appropriately.
Was this helpful?
Thank you for voting!
washer would not agitate
1 person
found this instruction helpful.
-
Lucas from hastings, MI
- Really Easy
- Less than 15 mins
-
Socket set
The part came very fast and was easy to install, I pulled off the agitator and removed one bolt, replaced worn out part with new part and put the new bolt that came with the part in. Reatached the agitator and washed some clothes. done
Was this helpful?
Thank you for voting!
the washer would work but the agitator wouldnt spin
1 person
found this instruction helpful.
-
akram from lakewood, OH
- Really Easy
- Less than 15 mins
-
Nutdriver, Socket set
took out the agitator then removed the agitator coupli and found out that the coupli was worn out, i then replaced it and everything worked again
Was this helpful?
Thank you for voting!
agitator couplier was stripped out on the shaft
1 person
found this instruction helpful.
-
REX from PLEASUREVILLE, KY
- Really Easy
- Less than 15 mins
-
Wrench set
I put my fingers under the agitator and pull up , this pulled it off the couplier, then I used a 11mm wrench to remove the bolt that holds the couplier in place and pulled the couplier off, the new couplier didnt arrive until after I went to work but my wife had it all back together when I got back home,I told her what to do and she said
... Read more
it only took about 10 mins. to get together, very easy.
Read less
Was this helpful?
Thank you for voting!
Washer would not agitate
1 person
found this instruction helpful.
-
Mary Ann from Waynesburg, PA
- Really Easy
- Less than 15 mins
-
Socket set
We removed the agitator then the bolt holding couplier. The inside of the plastic couplier had stripped after 5 years. We cleaned around the metal part of the agitator then installed the new GE plastic couplier, put in the bolt & replaced the agitator. The machine works better than ever.
The GE website said this part had t ... Read more o be replaced by a certified technician. The estimated service call alone was $80 & the part was not available from the GE website.
The GE website said this part had t ... Read more o be replaced by a certified technician. The estimated service call alone was $80 & the part was not available from the GE website.
Read less
Was this helpful?
Thank you for voting!
Water was not draining from washer
1 person
found this instruction helpful.
-
Jesus from Casa Grande, AZ
- Really Easy
- Less than 15 mins
-
Pliers, Wrench set
My wife calls me and says that the washer is not draining water so I was like "great"...here goes more money. After I tried draining, cleaning, checking for leaks, I looked up possible causes and came across the water pump. I have bought from parts select and I love this website so I jumped on here, found the causes, diagram, installatio
... Read more
n videos, and cheap parts. Added to cart, paid, and was here in about two days. I disconnected the electricity, opened the front lid, took off the two hoses, unscrewed the pump, swapped in the new one and hooked it back up. The washer works like new, took me about 10 minutes. Thanks Partselect!!!!
Read less
Was this helpful?
Thank you for voting!
broken start knob
1 person
found this instruction helpful.
-
Bruce from MONROEVILLE, PA
- Really Easy
- Less than 15 mins
Just push knob on less than 4 seconds
Was this helpful?
Thank you for voting!
Broken knob and could not turn on dryer
1 person
found this instruction helpful.
-
James from YARDLEY, PA
- Really Easy
- Less than 15 mins
-
Pliers
followed the video you provided and it was easy!
Was this helpful?
Thank you for voting!
The Start knob broke off
1 person
found this instruction helpful.
-
Sally from MANHATTAN, KS
- Really Easy
- Less than 15 mins
At first the knob seemed like it would not fit on, but after I sprayed it with WD-40 oil, it slipped with a gentle, steady push
Was this helpful?
Thank you for voting!
would not drain water
1 person
found this instruction helpful.
-
Frank from Western Springs, IL
- Really Easy
- Less than 15 mins
-
Socket set
Very easy with your great instructions in my email. took the wires off,took the hoses off,then the two bolts,put the new one on and reasembled the hoeses wires and bolts. put the front back on and that was that. Your company is great thanks for all your help.If I ever need help again with any off my appliances i will call on you,agin than
... Read more
k you very much. Frank!
Read less
Was this helpful?
Thank you for voting!
Washer would finish a cycle and the water would not drain the tub.
1 person
found this instruction helpful.
-
Ryan from Beaumont, CA
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
I took off the front of the washer with two screw drivers. Removed the hose clamps with the pliers then removed the two screws with the nut driver and changed out the pump. Nothing to it. Easy fix, it works like new for $45 and 15 minutes.
Was this helpful?
Thank you for voting!
water leaking from bottom of washer
1 person
found this instruction helpful.
-
jeffrey from willard, NC
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
removed back off washer, disconnected pump from washer tub, remove old pump in about 5 min, then installed new pump in less than 5 min. washer is working just fine wife thank me it was about 2 wks since the washer was down.
Was this helpful?
Thank you for voting!
Pump was broken
1 person
found this instruction helpful.
-
Dawn from Singers Glen, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
So easy to fix. The best thing about it all was the guidance of the website. We were able to locate the exact part and followed the instructions on how to replace, piece of cake!
Was this helpful?
Thank you for voting!
Water pump failed
1 person
found this instruction helpful.
-
John L. from Mandeville, LA
- Easy
- Less than 15 mins
-
Nutdriver, Pliers
Pull front cover and changed pump. Your delivery of this part was remarkable. Thanks for such good service.
Was this helpful?
Thank you for voting!