WSSE5210B2CC General Electric Washer - Instructions

First I found out on the web how to open the washer's front cover.
For the strap in the front, it's relatively easy to replace a strep if your hands are somewhat flexible.
For the one in the back, I also needed to open the top dial panel, in order to lift the main lid connected to it, in order to then be able to reach one of the ... Read more screws of the back strap. the other one of its screws I was able to reach from the front with a ratchet and extension from the front. Arms do get heavy from time to time, but overall it was manageable.

Use flat head screw driver to push in clips that hold on front panel.
use plyers to remove hose clamps on motor and remove hoses.
use nut driver and remove two screws holding bracket in place. disconnect two wire plugs.
Install motor and work above in reverse.
very simple 15min job at most.

e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) that were easy

Removed the old one and installed the new pump, by removing the front cover and disconnect everything.

Took new one out of package, and push it on. 4 seconds!

I put the nob on the post, one side is flat the rest of the lever on the dryer is round. So I matched up the lever with he inside of the new knob and slid it on . The dryer works perfectly. I ordered it on May 5 th and the nob arrived May 15 th. I guess Georgia is a long way from Arizona. But the part fit perfectly and I am happy. Tha ... Read more nkyou.

After much research I decided to have to repaired all new models were not good. Reached out to local service repair because I beleved that it was the timer. $270 for service call REALLY and $125 for part.
Reached ot to PART SELECT LOVE YOU GUYS) SAID WHAT WAS THE PROBLEM the chocie was a new knob or replace timer. I am
8 ... Read more 3 yr old woman and believe I could have done it myself if it wasn't for the problem of moving the dryer out. shut off electric four screws
take out old replace new rewire the four screws WORKING NEPHEW
DID IT IN TEN MINUTES NO CHARGE BUT THANK YOU PART SELECT FOR REAFFIRMING MY DIAGNOSIS. AUDREY

After receiving the wrong part 2x instead of magnet assy I received a metal clip ring. ordererd magnet assy from another source. iNSTALLATION IS VERY SIMPLE. REMOVE 2 SCEWS IN THE LID WHICH HOLD THE MAGNET IN PLACE AND REPLACE THE MAGNET WITH NEW ONE. TEST TO MAKE SURE ALL OPERATIONS ARE NORMAL.

First i noticed a small leak coming from the pump assembly dripping onto the motor/pump bracket with indications that it had been doing this for some time.Looking @ this i then took the pump/motor assembly off cleaning the inlet and outlet of pump off so i could plug one side of the pump while blowing into the inlet side of the pump verif ... Read more ying that the gaskets around the pump assembly was in fact leaking.Replacement was very easy.Purchased a new pump/motor assembly from parts select and received it in three days.Used a flat tip screw driver to press on top front clips pulled away from front of washer then up and off.The pump/motor assembly only has two screws holding it down then i pulled off the electrical connector after that used channel locks to remove both inlet and outlet hoses off pump.Installed new. very easy

If you follow the video that part select provides you will be just fine.

I was going to replace the washer. .. I am a cabinet maker and pretty good at what I do. I have to admit before seeing the video I was out of my comfort zone with this repair. I was shown not only the part needed and that you folks had the part in your inventory on hand. I was pleased to see how inexpensive it was $7.40. I had it shipped ... Read more for $8.70. I ordered online at 2 pm. the part arrived the next day at 1 pm. AMAZING!. I spent ten minutes making the repair. The machine is now back to it's like new self! Regards, MichaelAndrews.biz

***Partselect.com had my ordered part delivered within 3 days.*** First, I pulled up on agitator and removed it. Then, loosened bolt on coupling and removed it. Replaced with new coupling, placed and tightened new longer bolt that came with new coupling. Replaced agitator and started laundry.

I first placed a rope under the fins of the agitator and used a 2X4 board to pull up the agitator which needed very little force to release itself from the agitator coupling. I removed the nut holding the agitator coupling, removed the stripped agitator coupling. Installation was just the reverse process, inserted the new agitator couplin ... Read more g, placed and tightened the screw, and pressed down the agitator over the agitator coupling and I was done. Over time for the repair was between 5 and 10 minutes, very easy, and I have no experience repairing washing machines.

I just added the agitator coupling and screwed it in.

I am a mother of 3 so a washing machine is vital. I called various appliance repair places and was quoted anywhere from $50 - $85 just to come and look at it. I did some online research and discovered that the part itself was less than $7. After paying for 2-day shipping, my total was under $20. I thought, what do I have to lose. I receiv ... Read more ed the coupling kit and read the EASY instructions. I had already removed the old one so by the time I received the new one, it took me less than 10 minutes. WOW!! I now have a working washer!! .THINK AGAIN!!