WRX735SDHV07 Whirlpool Refrigerator - Instructions

Removing the old unit was difficult. The light was clearly designed for installation not for ease of repair. Since I was concerned about marring the surface of the refrigerator I used a paint scraper to get under the lip of the light and another smaller paint scraper to lift the unit away from the body of the refrigerator. It does not ... Read more just "pop off". I eventually did get it free without any damage to the wall of the refrigerator. The repair was then very easy. There was a connector that was easy to separate allowing for the removal of the old unit without cutting any wires. The new unit had a mating connector, which easily connected to the old connector in the refrigerator. After some pushing I was able to install the new unit into the hole in the refrigerator. It does not exactly "snap in".

researched on line and found the wiring was in series and I the suggestion was to replace the first light in the series that was in the freezer. Ordered the replacement light board and took out the existing light and pooped in the new one. Lights now all work! 15 minutes at tops.

just like the video showed, removed the cover parts inside the fridge, disconnected the water tube inside and pulled out from the top of fridge, then inserted new water tube.

From Donna Turner acct # 190766

I ordered Refrigerator/freezer light board PS11702378

You substituted for a single light module

I troubleshooted and decided to order from your company the light board. You changed my order. I researched what you sent and thought, ok, we'll identify the one light that is ou ... Read more t and replace only that...

My paid electrician spend well over an hour inside the frig, and confirmed that all 3 lights in fact work fine, and the problem is above the wiring harness, and what you sent is not correct.

The package has been opened. You substituted my ordered part, it did not remedy the problem, I want a full refund, including S&H

Please advise/sent me Return Authorization, whatever your company policy is.

Thank you. Donna Turner

Lower the filter bottom housing to gain access to the filter. Unscrew the filter and install the bypass cap. Secure the lower filter housing to the top assembly.

I called the installer of my filter unit and he told me that often, thhe fridge filter is the problem. Like magic it worked

Remove first cover remove the light panel and replace it
Install everything back...

Unscrew filter. Screw on filter bypass

I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.

Shut off water supply. filter is located in the upper right hand corner of the refrigerator on the inside. open the drop-down door. by hand pull the filter downward. then twist it to the left one quarter turn. it should pull out. I replaced it with a filter bypass plug. you can purchase a high quality filter to replace.it don't buy cheap ... Read more filter.I made that mistake! hope this helps good luck!

Bought new cap.

Checked Video online. Had to remove the 2 snap on track/gear covers. Pry out the gear with screwdriver and the gear bearing unit. Align the flat side of the bearing unit and snap in. Position the cut teeth on the gear to match original and snap into the bearing. Insert the connecting rod into the long shaft gear and then push back into ... Read more the short shaft gear. The video said to remove the drawer front but I did not and don't see that it necessary.

Looked at the appliance's booklet to see how it fit together, then installed it.

Took out 2nd new filter $43.00 each that clogged in less than 2 weeks each and installed in 2 mins. this bypass and ice and waterr work perfect.Thank you, thank you for your exceptional service ordered part and it came next day without extra charge,great service.

We had an Appliance Repair service come to fix, and they replaced the ice maker and the water valve, but ice maker was still not performing properly. We use RO water to fill the ice maker and because the water was also going through the charcoal cartridge, there wasn't enough water pressure to completely fill the tray. Plus charcoal filte ... Read more r was probably clogged. The original Blue Bypass Cap was nowhere to be found and I even called Kitchenaid to get one. They were of no help. But found your site, and found the part I needed. And best of all, ice maker is not jamming and is now making real ice cubes, not hollow, thin ones. And the water dispenser is now working too, so am very happy that such a small thing, fixed the big problem. Who knows, a clogged charcoal filter may have been the whole problem from the start.