Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Cracked shelf
2 of 2 peoplefound this instruction helpful.
Leonard from WARRINGTON, PA
Really Easy
Less than 15 mins
Snapped it in shelf in designated slots
Was this helpful?
Thank you for voting!
crack
2 of 2 peoplefound this instruction helpful.
w l from PIKESVILLE, MD
Very Easy
Less than 15 mins
pull off the old gasket and push on the new one into the channel...
Was this helpful?
Thank you for voting!
torn and cracked gasket
2 of 2 peoplefound this instruction helpful.
janet from Parryville, PA
Very Easy
Less than 15 mins
Took off the old one, replace the new one in less than 5 minutes
Was this helpful?
Thank you for voting!
Old door seal was cracked and didn't seal tight.
2 of 2 peoplefound this instruction helpful.
Rosemary from FRUITPORT, MI
Very Easy
Less than 15 mins
Pulled off the old seal and put the new one on. No tools needed. It fit where it was supposed to and seals the door like new now! Thank you!
Was this helpful?
Thank you for voting!
Lost the temperature control know
3 of 5 peoplefound this instruction helpful.
John from Pilesgrove, NJ
Really Easy
Less than 15 mins
The knob came in the plastic package. It was the correct part. I opened the package and placed the knob on the prongs. Now it works fine.
Thanks John S.
Was this helpful?
Thank you for voting!
plastic drawer slide was broken
2 of 2 peoplefound this instruction helpful.
brenda from hillsboro, MO
Really Easy
Less than 15 mins
Screw drivers
First I watched the video that provided - extremely helpful - thank you- when the part arrived I removed the drawer and shelf - unscrewed the screw- pushed the slide catches to one side and removed - then I screwed new slide on - pushed to lock in the catches and DONE! That simple - EASY PEESEY!! THANKS SO MUCH FOR VIDEO AND SUPER FAST NE
... Read moreXT DAY SERVICE - AMAZING HOW FAST!! WILL USE ANYTIME I NEED PART AND HIGHLY RECOMMEND YOUR SITE! TIME- 5 MINUTES TOPS!
Thawed out freezer, I recommend laying a couple old towels in freezer to soak up melted ice. Replaced old thermostat with new part. Removed 2 screws, removed back plate, unplugged 2 connectors and cut 2 wires. Crimped in new thermostat and repositioned to original part location. Reconnected plugs as I reinstalled back plate. Installed 2 s
... Read morecrews and connected power. Works like new! Trouble shooting and part installation video is very helpful, great site!
Read less
Was this helpful?
Thank you for voting!
Rail had split and would not support drawer.
2 of 2 peoplefound this instruction helpful.
Douglas from HOUSTON, TX
Very Easy
Less than 15 mins
Screw drivers
Removed drawer. Removed shelve. Flipped shelve over. Removed one screw. Undid tab on each end. Removed bad rail. Replaced with new rail and reversed order. Easy fix.
Was this helpful?
Thank you for voting!
freezer cold and frosting up but refrigerator warm
2 of 2 peoplefound this instruction helpful.
Gary from SABINSVILLE, PA
Very Easy
15 - 30 mins
Nutdriver
inside the freezer compartment, remove four hex head screws from rear panel,lift panel forward and unplug wire assembly from panel. find old defrost thermostat attached to copper tube by clip on back of thermostat, unclip, snip two wires to thermostat, take new thermostat, strip 1/4"of wire from wires in freezer (thermostat is prestripped
... Read more),insert light blue wire from thermostat and light blue wire from freezer into opposite ends of crimp connector and crimp securely. repeat with dark blue wires. set panel back in freezer,connect plug to back of panel, refasten screws and you are go to go! save yourself the price of a new refrigerator or $300 repair by repairman!
Read less
Was this helpful?
Thank you for voting!
the freezer frosted up and the fridge was not getting cold.
2 of 2 peoplefound this instruction helpful.
Sherry from Newberry, SC
Easy
30 - 60 mins
Nutdriver
I watched the instructional video and did what it said.
Was this helpful?
Thank you for voting!
Gasket was oversize and compression spline would not stay in door groove
2 of 2 peoplefound this instruction helpful.
CECIL from PHOENIXVILLE, PA
Difficult
1- 2 hours
Required a trip to the hardware store. Online research showed that Gorilla Glue would hold gasket in place and was recommended for that task. Needed to glue each side separately to keep the spline in the groove. Took far longer than it should have!
Was this helpful?
Thank you for voting!
Broken Door Bin
5 of 12 peoplefound this instruction helpful.
GEORGE from CAMBRIA HEIGHTS, NY
Really Easy
Less than 15 mins
I just replaced the door bin. It was very easy.
Was this helpful?
Thank you for voting!
old refrigerator door shelf broke
2 of 3 peoplefound this instruction helpful.
Rod from Rio Rancho, NM
Really Easy
Less than 15 mins
Installing the new shelf was easy.
Was this helpful?
Thank you for voting!
Broken meat pan on Kenmore refrig
2 of 3 peoplefound this instruction helpful.
Robert from Los Angeles, CA
Really Easy
Less than 15 mins
Just slid it in. Fit perfectly. Called the Help Line just to double check that the pan would fit and they assured me it would. Pan cost $20 less than through the Sears site because of lower price, lower shipping and no taxes. Oh, and the pan came in just two days. Very happy.
Was this helpful?
Thank you for voting!
the refrig was in storage for about a year, the freezer door warped
3 of 6 peoplefound this instruction helpful.
Jeffery from Phillipsburg, NJ
Really Easy
Less than 15 mins
removed freezer door and installed the new one. This was a pretty easy thing to do, although putting the old handle on the new door was a challenge. No knowing that there is a plastic piece holding the top of the handle i broke the that piece and had to order another one. Mean while the freezer was making alot of frost inside, so that
... Read morehad to be cleaned after the new part came.
My Orders
