WRTS23V7MW2 Frigidaire Refrigerator - Parts

This retainer bar (Refrigerator Door Shelf Bin, Refrigerator Door Shelf, Door Shelf Bin, Refrigerator Door Bin) holds items on the refrigerator door shelf. The plastic retainer can become brittle with time and crack or break under the strain of normal use. It can also break if heavy items are placed in the door shelf. If this part will no...Read more longer hold securely onto the inner door panel it will need to be replaced. This model is white plastic, and measures 26 by 5 inches. Sold individually.

As you look into the fridge, this drawer support track is located on the right-hand side. This item is white in color and made of plastic. The drawer support track can wear out over time. The only tool required is a Phillips screwdriver. Empty out the drawer and remove it by sliding it forward. Lift out the shelf, remove the screw on the ...Read moreside of the shelf, remove the rail by pushing the rail forward and snapping out of place, insert new rail, and install the screw back in. Now the shelf can be put back into the refrigerator. The mounting screws are sold separately.

Frost near the door, long cooling cycles, or a warm refrigerator can result from a cracked or twisted fresh-food door seal. The gasket forms a tight barrier between the door and cabinet, helping hold cold air inside. First check for spilled food, loose hinges, bent door parts, or shelves that stop the door from closing. Match the replacem...Read moreent to the full appliance model before ordering. Disconnect power and move food to a cooler during the repair. Smooth shipping creases with warm water or low heat, but do not overheat the material. Install the seal without stretching it, then test several spots around the closed door with a sheet of paper.

This drawer rail supports the left hand side of the sliding drawer. The mounting screws are sold separately.

This defrost thermostat is also known as a refrigerator defrost bi-metal thermostat kit. The function of the defrost bi-metal thermostat is to prevent overheating during the defrost cycle in your refrigerator by protecting the evaporator. The most common sign that there is a problem with your refrigerator defrost thermostat kit is if your...Read more freezer is cold but your refrigerator is warm. If your evaporator coils are icy then your defrost bi-metal thermostat kit could be defective. To do this installation the tools you will need include a 1/4 inch nut driver, a pair of wire strippers and crimpers, and a heat gun.

This small, Phillips-head screw works with your refrigerator/freezer. It screws in to the freezer door and connects to the door handle. This part is made of stainless steel and is sold individually. This is an OEM part sourced directly from the manufacturer.

This is the replacement meat pan for your refrigerator. It is made of clear plastic and is approximately 18 inches long and 13 inches wide. The meat pan slides into the bottom of the refrigerator shelf and is used to store meat and other food items. The main reason to replace the meat pan is if yours is cracked, damaged, or missing. To re...Read moreplace the meat pan, simply slide the old pan out, and slide the new one into place. This part is an OEM part sourced directly from the manufacturer, and is sold individually.

This evaporator fan blade is a genuine OEM part that is sourced directly from the manufacturer. The evaporator fan blade circulates air through the refrigerator to control the amount of cold air goes that goes to internal compartments of the unit. It may need to be replaced if the fridge is noisy or not cold enough. This part is made of p...Read morelastic and is sold individually. It will be necessary to disconnect power to the refrigerator and empty the freezer compartment of the refrigerator. The tools needed to complete this repair are a 1/4 inch nut driver and a pair of needle nose pliers.

This is a replacement hinge bearing for your refrigerator. The hinge bearing is found on the door hinge, and reduces friction when the door opens and closes. If the bearing is damaged, you may not be able to open or close the door properly, and in this case, it will need to be replaced. It is made of white plastic and is approximately 2 i...Read morenches long and 1 inch in diameter. This part is sold individually and is a genuine OEM part.

This part blows air over the condenser.

Improve door function and alignment with this hinge nylon washer, designed to support the door as it pivots on the hinge pin. Made from durable nylon, it helps reduce friction and noise while ensuring smooth opening and closing. By maintaining proper door positioning, it supports a secure seal and contributes to efficient operation and consistent cooling performance.

Sold individually.