Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Handle broke at screw hold down area
1 personfound this instruction helpful.
anthony from BRADENTON, FL
Really Easy
Less than 15 mins
Screw drivers
Remove the screws and pivot handle. Push handle downward and it slides off the screw head sticking out of door. To replace handle, just work in reverse. It Didn’t take more than 3-4 minutes to do the whole job.
Was this helpful?
Thank you for voting!
Broken door rack
1 personfound this instruction helpful.
Laura from RAPID CITY, SD
Very Easy
Less than 15 mins
The repair was very easy just popped the new one in place.
Was this helpful?
Thank you for voting!
Light not turning on when door opened
1 personfound this instruction helpful.
Michael from TUCSON, AZ
Very Easy
Less than 15 mins
Screw drivers
Used a flat head screwdriver to pop out the old switch, removed the contacts and placed on the new switch, popped the switch back in. Done in about 2 minutes.
Was this helpful?
Thank you for voting!
Shelf rack broke.
1 personfound this instruction helpful.
Nancy from SELINSGROVE, PA
Really Easy
Less than 15 mins
Ordered part easily with modal number ( they tell you where to find it). Received quickly and snapped paper in. They also had a video instruction. Will definitely use again!
Was this helpful?
Thank you for voting!
Refrigerator wasn't getting cold
1 personfound this instruction helpful.
Brad from STOCKTON, CA
Very Easy
15 - 30 mins
Nutdriver
removed the back panel of the freezer and unplugged the connector for the Motor. Removed the air diffuser, then removed the fan blade. Removed the 2 screws holding the motor to the bracket. Disconnected the old wire harness and installed the new one. Put the fan blade onto the new motor and installed the motor onto the bracket. Put the ai
... Read morer diffuser back on, plugged the motor back in and fastened the back panel. Plugged the refrigerator into the outlet and tested, OK!
Read less
Was this helpful?
Thank you for voting!
Fridge quit working.
1 personfound this instruction helpful.
Bill from Bay City, MI
Easy
15 - 30 mins
Nutdriver, Screw drivers, Wrench set
A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy i
... Read morenstallation, just in a tight space on my model.
Read less
Was this helpful?
Thank you for voting!
Fan motor in the freezer was not working. The freezer was still cool enough to keep the food froozen, but the refrigerator was not keeping the food cool and the liquids were getting warmer than normal.
1 personfound this instruction helpful.
Eric from SOUTH HAVEN, MN
Very Easy
30 - 60 mins
Nutdriver
Very easy process. Watch the YouTube video, it goes step by step for the repair. The part was $33, shipping was $6. Take your time and fix it yourself or pay $500 for a new refrigerator.
Was this helpful?
Thank you for voting!
Evap fan motor comes on and off will not stay running
1 personfound this instruction helpful.
john from NEWHALL, CA
Easy
30 - 60 mins
Nutdriver, Pliers
pulled back panel to get at evap fan motor cut wires to remove reinstalled hooked up wires
Was this helpful?
Thank you for voting!
Noise from fan
1 personfound this instruction helpful.
Reginald from WEST PALM BCH, FL
Really Easy
30 - 60 mins
Socket set
I watch the video on your site and this make iit very easy to do. That repair that tooks me 40 minutes.
Was this helpful?
Thank you for voting!
Freezer worked, no fridge
1 personfound this instruction helpful.
Adam from BERKSHIRE, NY
Very Easy
30 - 60 mins
Nutdriver, Pliers
Removed panel over the motor in the freezer department. Removed screws holding the motor in, unplug wires. Reversed process to install motor.
Was this helpful?
Thank you for voting!
FREEZER COMPARTMENT NOT COLD ENOUGH (20 DEGREES)
3 of 7 peoplefound this instruction helpful.
DANIEL from CAPE CORAL, FL
Really Easy
30 - 60 mins
REPLACED TIMER-DEFROST 215846602..REPLACED THERMOSTAT-DEFROST KIT 5303918202..REPLACED CONTROL, TEMPERATURE 5304421256..RECHARGED SYSTEM WITH 134A...ALL FANS WORKING...COMPRESSOR RUNS.. FREEZER STILL NOT GETTING COLD ENOUGH...HOLDING AT 20 DEGREES...ANY SUGGESTIONS..THANKS..DAN
Installation was fairly straight forward. The major complaint is that the problem returned 2 weeks later. I don’t know if I care to re-invest in another switch. Now what?
Was this helpful?
Thank you for voting!
The hole on the handle mounting block was too low
1 of 2 peoplefound this instruction helpful.
Sadrudin from SAN DIEGO, CA
Difficult
30 - 60 mins
I had to loosen the screw holding the mounting block and increase the hole size to fit the screw on refrigerator
Was this helpful?
Thank you for voting!
Fridge and freezer both freezing at bottom and warm at top.
1 of 2 peoplefound this instruction helpful.
Stephen from PERRIS, CA
Really Easy
1- 2 hours
Nutdriver, Pliers
Unplugged fridge. Removed freezer shelves and unscrewed and removed plastic shelf brackets. Removed the lower rear panel. Removed the bin for ice. Removed the 2 exposed upper rear panel screws. At this point I was able to flex the panel quite enough to access the fan motor. Carefully plugged the fridge back in and turned it on long enough
... Read more to verify the existing evap. fan motor was not running. Powered off and unplugged again. Removed the fan and it's support assembly, and replaced with new. Had to cut the wires and splice and crimp with the provided wire nuts since the plugs in this model were different. Powered on fridge to check fan function. Reassemble and go home looking' like a hero! Saved my BFF a couple hundred bucks.
My Orders
