WRT15CSHW4 Westinghouse Refrigerator - Instructions

I watched the video online. It was so easy! All I needed was a screwdriver. It looks great.

The end caps worked perfectly for both the Frigidaire and Westinghouse fridges. Just pulled out the old end caps and then literally just pushed in the new ones (remember to attach the shelf bar before attaching the second end cap!). The pieces arrived quicker than expected. Thanks Partselect!

Simple switch repair: Unplug fridge, pull down to remove switch assembly, slip contacts off. Reverse with replacement switch. HOWEVER, check first to see if the bulb filament might be broken, as this could cause the same symptom. OR in my case, the light socket connection was the culprit. Check that too before ordering a replacement s ... Read more witch.

The site offers a video for this part which worked perfectly. In addition to replacing the part, since the cardboard panel was off, we also cleaned all the dust off of the coils which someone recommended to do annually.

Replaced both the thermostat and defrost timer and still froze up and still warm air to the fridge, turned out to be the defrost heater coil. It was cracked in the middle, very easy to test with a multimeter. Replaced the heater coil and all is like new!

Removed evaporator cover, unplug 2 wires to thermostat, unclipped it from the coil. Installed new themostat back the same way.

removed doors and took out screws from hinge and replaced hinge. works great, all costs under $20, applinance store said no parts available only wanted to sell a new appliance, no wonder they are all losing bussiness when they have custmor service like this!

I pulled out the old pieces and poped what I couldn't into the foam insulation behind the support. Then I placed the new piece in the hole and popped the plastic pin to seat the support. bang. the only problem I had was knowing if it was the right part by the picture. The little pin that had to be pushed through kinda threw me.

Twisted replacement bulb into place easily. Let there be light!

Did the obvious. Removed the stick-out cover, then the back of the freezer wall, after taking the bad evaporator fan out. Replaced the old motor with the new one, stuck the fan blades back on, and put the replacement back in place. Checked to see that the new motor and fan, before final hook up, had no issues. That was a success. How ... Read more ever, when I put the parts in place, I had some significant vibrations. By taking things apart and re-doing the install, the vibrations went away. However, the final install, even if quiet, did not work. Apparently the condenser was kaput. No cooling after all the adjustments. We gave up and are replacing the fridge.

I removed the plastic cowl in the rear of the freezer to gain access to the fan, took out two screws that secured the brackets holding the fan. Then I separated the coupling wires which had a sort of locking mechanism that was simple to undue. I took out the brackets along with the fan, separated the brackets and removed the screw for the ... Read more ground wire. Then I simply reversed the process.

I opened the fridge door and lifted up the old gasket to investigate the situation. I saw that the inside door panel (the one that has the butter compartment and additional shelves for condiments) had screws every few inches. I determined that this was holding the smaller lip of the gasket in. I got out my trusty cordless drill and wen ... Read more t to work. After a few mild cuss words, I did manage to get the very last corner on, as that is the trickiest part of the installation. Note that I am an almost "60" year old woman who has many other tools, including a chain saw, which I utilize every now and then. So if I can do it myself, I certainly will! The best thing of it all was that I ordered the part on 8/22/08 and when I arrived home the evening of 8/24/08, the box with the part was sitting on the back deck. Thank you partselect for a great product and great service.

Removed the old and installed the new. Electrical plug/socket made connection easy. Biggest problem is working space in freezer side of a side by side with the fan in the back. If I can do it anyone can.

I unscrewed the old handle. lined up the new handle and screwed it back in.

I first replaced the defrost timer about a week prior and it did not correct the problem. I then ordered the thermostat from partselect and within 15 minutes had the part installed. My refridgerator has been running correctly for a couple weeks.