This is an OEM replacement ice and water filter for your refrigerator. In side-by-side refrigerators, it is found in the top right corner or the bottom left grille. In bottom-freezer refrigerators, th...
Sold individually. This door bin is for refrigerators.
The door bin attaches to the inside of the refrigerator door and typically holds jars and bottles.
This light switch may also be known as a refrigerator door switch or a light switch kit, and is compatible with your refrigerator. The function of the refrigerator door switch is to turn on the light ...
This mounting screw is a genuine OEM replacement part for the door handle in your refrigerator. If you are having trouble shutting the refrigerator door, or opening it, replacing this screw can help s...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
This door bin is clear with a white trim across the top. This part measures approximately 18 inches wide by 3-1/2 inches high by 6 inches deep. Sold individually.
This part is a replacement refrigerator drive shaft seal for your refrigerator. The drive shaft seal protects the auger motor from water and condensation that may leak down the drive shaft from the ic...
If your refrigerator or freezer is too warm, or making noises, you may need to replace the fan blade. The fan blade attaches to the evaporator motor, which is in the freezer section, to help circulate...
This ice maker is for refrigerators.
Ice maker includes the ice mold and the control device. The ice maker receives water from the water inlet valve and then holds the water in the ice mold until t...
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Larry
February 23, 2020
I installed new ice maker, it worked once in 72 hours. Arm will not drop down into ice container. How do i get the arm to signal ice level lowto the ice maker
For model number WRS571CIDM01
Hi Larry,
Thank you for your question. If you have just installed a new ice maker, please allow 24 hours before it starts to make ice. The arm should be in the up position until it cycles. The ice maker has an automatic shutoff to keep the storage bin from overfilling during normal operation. As ice is made, the ice cubes will fill the ice storage bin, and the ice cubes will raise the shutoff arm to the OFF (arm up) position. When the storage bin is at full capacity, the ice maker will automatically stop ice production, but the ice maker On/Off switch will remain in the ON (up) position. Try and press the on/off switch and then lowering the arm manually to see if this helps. If it not you may have to refer to the diagnostics tech sheet that came with your refrigerator or contact Whirlpool for more information. I hope this helps. Thank you and have a great day.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Barbara
November 27, 2019
Fridge not cooling
For model number WRS571CIDM01
Hello Barbara, thank you for writing. You will want to replace the Evaporator Fan Motor, part number PS11740362 for your model refrigerator to fix this. Good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Louie
February 4, 2020
My freezer keeps making a clicking sound when trying to dispense ice. I noticed there’s like a washer that suppose to hold the bar down that spins so it’s not loose when spinning. You have the part number for this I believe in the diagram it’s part # 5.
For model number WRS571CIDM01
Hello Louie, Thank you for the question. Item #5 in the Motor and Ice Container parts is the Spring Part #: PS11731230. We hope this helps.
The ice maker auger motor seemed to be burned out because it would no longer run freely even with no ice in the hopper.I ordered a new motor and installed it. result was the same issue. would not run at every request.
seems the switch is fine because the hopper door opens and the motor tries to run.
could the solenoid that activates the auger motor be going bad? i am thinking there must be some type of solenoid and/or a switching relay that provides voltage to the motor and its not getting the power its calling for? i also noticed that the water flow slowed down about the same time the ice maker started acting up despite changing the water filter.
thank you in advance for you suggestions.
For model number WRS571CIDM01
Hello Edward,
Thank you for your question. Our sources suggest replacing the water inlet valve under part PS11750831 for your model to fix the dispensing issues. We hope this helps.
Do my fridge have an air filter and also how can i get rid of bad smell and fruit flies out the interior behind panels in and the fridge and freezer.. please help me! or do i need to purchase a new one.. thank for your prompt attention in this matter.
sincerely ms. wayka ramirez
For model number WRS571CIDM01
Hello Wayka,
Thank you for your question. Your model does not have an air filter. You should be able to remove the interior panels to be able to clean the parts where the smell is coming from. First unplug the fridge or disconnect the power. Then hand wash, rinse, and dry removable and interior surfaces thoroughly. Use a clean sponge, or soft cloth and a mild detergent in warm water. Hope this helps!
I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.
First I removed the old lightbulb from the socket and replaced it with a new one to confirm that the bulb was not the problem. I then pryed the socket out with a flat-head screwdriver. I could tell that the socket was anchored in its hole with clips so it was relatively easy to pry it out. Once the socket was out, I disconnected the lead wires and ordered a replacement socket kit from Partselect. When the new one arrived, I reconnected the lead wires to it, snapped it back into its hole, screwed in a new lightbulb, and presto!! The light was back on with no further problem. Thank you, Partselect!! A $15.00 part saved me what probably would have been at least a $100. service call and heaven knows what the technician would have told me I needed!!!
I used a flat screwdriver and released the lock tab on the bottom of the light switch, and pried the switch out, being careful to not damage the plastic around the mounting place of the switch, unplugged wiring from old switch, plugged in the new one and pushed the new switch into place. Job finished light switch now working.
The Fix App makes it easy to manage all your stuff in one place. Just snap a photo and we'll find and store your user manuals, receipts, and product information in one easy-to-find place!
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
Stay on this site
Go to Canadian site
