WRF560SFHB00 Whirlpool Refrigerator - Instructions

I bought a new Whirlpool Refrigerator that didn't have an ice maker.
I wanted to install an ice maker. I searched your web site and found the model ice maker model it said I needed. WPW10715709. This one was a 4 wire 8 terminal. I needed a 4 wire flat connector. WPW10715708. You approved the return. It cost me $50 to return it. I bel ... Read more ieve you should refund me the cost of this postage. Your web site gave me the wrong model number.

Thank you

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

From the time I started to finish I worked 3 hours, this included installing the new ice maker, cutting into the cold water line in the basement and installing a t with a 6inch piece of pipe with a compression valve to connect to the small cooper tube, this is worth your time to do it this way, its a lot better connection than the small p ... Read more ierce valves that come with the kit, they will leak over time. I installed the filter in the waterline in the basement for easy access

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

followed the instructions provided and that's it!

Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

Unplugged the refrigerator, removed the bottom freezer door, removed the two sliding shelves, removed the ice maker. Took the inside back wall off to expose the evaporator motor (have to bend it a bit to get it out. Used a small socket to remove the shroud and the evaporator motor. Installed the new motor and before putting it back tog ... Read more ether, plugged it in to ensure that the fan and motor worked. Then reassembled. Highly recommend knowing your brand and model#, and "Google" and YouTube it for additional help if you need it.

I removed the cardboard back then using a nut driver removed the three mounting screws, removed the old fan/motor and installed the new one, installing the three screws and replacing the cardboard cover.

My big problem was getting the right parts. Don't ever order refrigerator parts using the refrigerator model number. I did ... Read more and got the wrong part, sent it back and talked to the parts lady and ordered again describing the error, the needed parts shape etc and she sent me the exact part I had sent back. I sent it back and removed the fan motor to get the part number, called and ordered by number and got the right one. Hallelujah!

Easiest repair ever! Took maybe 5 minutes. Use the flathead screwdriver to push down on the three tabs holding the track onto the glass shelf and gently remove the old track. The new track snaps right in. Put the shelf back in the fridge, slide in the tray and it's done!

i had used your web site before and i read several problems that your readers had. i went to the back of the unit, removed the bottom cover and right there the i found the run capacitor and i chaged it. since i had only ordered this part to save money i went back and ordered the Start Device which when i took it off it was completely burn ... Read more ed. the replacement part came labeled with 2 different compressor #, so i picked the one that i had and unpluged each wire. the part may differ from the one that it's in the unit but it worked when i pluged everything back on. it also helps to take a picture of everything before removing the wires in case you have to leave it and come back later. i hope to use this refrigerator another 10 years. thank you all for your help.

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

I read the other comments on how easy the repair was, followed their advice, and it worked like a charm. Just use a screwdriver or butter knife to pop the track off the shelf and pop the new one back in.

The hardest part was getting the items in the refrigerator out of the way!

Unscrewed the old one and put the new one in
Some water on shelf of fridge
Overall not bad

We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.

Very simple, easy, and quick! Anybody can do it!!