WM3499HVA (ASSEPUS) LG Washer - Parts

The hot water inlet valve on your washing machine controls the water flow into the washer. This inlet valve has a standard hose fitting inlet and one water outlet. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the washer may leak, fill slowly, or not fill at all. To test yo...Read moreur valve, unplug the washer when the symptom occurs. If the washer continues to fill, then your inlet valve is defective. This part is approximately 3 inches long x 3 inches wide.

This hook locker, commonly referred to as a door lock strike is specially designed for LG washers. It is a small, metal plate that is attached to the washer door. When the door is closed it engages with the door lock mechanism to keep the door securely shut while the washer is running. If it is damaged, worn down, or corroded, it will be ...Read moreunable to engage with the locking mechanism and prevent your washer from closing or staying shut. You may notice that your washer will not start or stops running mid-cycle. You will need to replace the door strike to fix the washer.

This is a door lock switch, compatible with various models of LG washing machines. This door lock switch is designed to communicate to the control board when the door of the washer is closed, so the door can lock and allow the washing cycle to safely begin. If your washer is having difficulty locking before it begins its washing cycle, or...Read more if it has difficulty starting in general, you may need to replace this lock switch. This switch is made primarily of black, gray, and white plastic, and will require a screwdriver/drill, and a pair of needle nose pliers to replace. This door switch is a genuine OEM part that will require you to disassemble part of your washing machine to completely replace it.

This washer shock absorber mounting pin secures the suspension damper to the outer tub and base frame, helping stabilize the wash basket and reduce vibration during operation. By maintaining proper alignment of the shock absorber, it helps prevent excessive movement, banging, shaking, and loud thumping noises during high-speed spin cycles...Read more. Replacing a worn, damaged, bent, or missing mounting pin can restore the effectiveness of the suspension system and help protect other washer components from unnecessary stress and wear. Installation typically involves removing the retaining clip, disconnecting the existing pin from the shock absorber mounting point, inserting the replacement pin, and securing it with the appropriate retaining hardware. For best results, inspect the shock absorbers, retaining clips, and mounting brackets for signs of wear or damage and replace any faulty components at the same time to ensure smooth, stable washer operation.

This is a replacement shock absorber for your washer. The shock absorber is approximately 10 inches long and a little more than one inch wide. It is black and silver in color, and is sold individually. There are four shock absorbers on your washer. They support the tub and prevent it from shaking around. If your washer is shaking or makin...Read moreg a lot of noise during operation, you may need to replace the shock absorber. It is important to determine if you have one or more shock absorbers that need replacement before you begin the repair. This is an OEM part from the manufacturer.

This levelling leg is a genuine replacement part. It is used to help keep your washing machine stable and balanced. It helps support your appliance. It screws into the base of your washer, and you can thread it in or out to adjust the height. The foot on this leg is made of rubber, which helps with grip, stabilization, and vibration reduc...Read moretion. It is also hexagonal in shape, which allows you to more easily adjust it. This levelling leg features a locknut on the shaft which can be tightened against the bottom of your appliance, this will stop the leg from rotating while you are using your washer. This replacement is sold individually.

This washer door gasket, also known as a door boot, is specially designed for Samsung front-load washing machines. It is a rubber seal that is fitted around the opening of the washer. The gasket forms a watertight seal between the door and the drum to prevent water from splashing out during the wash cycle. Over time, the gasket may fail d...Read moreue to normal wear, build-up of detergent and laundry residue, or accidental damage, leading to issues like leaking or mold growth. If the door gasket is faulty, it is recommended to avoid using your washer until you have replaced it.

Also known as the water supply hose.