WF42H5000AWA2 Samsung Washer - Parts

This washer door lock and switch assembly is a critical safety and control component for front-loading washing machines. It secures the door during wash and spin cycles, preventing accidental opening and ensuring the appliance operates only when properly latched. The integrated interlock switch communicates with the washer’s control syste...Read morem to verify door status, helping prevent cycle interruptions and operational errors. This model features a four-lead switch for precise functionality and is compatible with a wide range of front-load washers. Replacing this part can resolve issues such as a door that won’t close, won’t open, or won’t lock, as well as a washer that fails to start. Installation should be performed with the appliance unplugged and may require basic tools.

This part is used for the shaft on the rear of the tub and is sold individually. The head bolt is part of the spider arm assembly, and they are generally changed at the same time. If you are replacing the entire spider arm assembly, make sure you order as many hex bolts as you will need. The spider arm assembly contains 6 of these hex bol...Read morets. The hex bolt or spider arm assembly may need to be replaced if you notice that your inner tub is going out of balance. The hex bolt measures 1.5 by 0.5 inches.

A washer that walks across the floor or becomes unusually noisy may have a weak suspension damper. The rear shock absorbs tub movement during washing and spinning, helping the machine run more smoothly. These symptoms do not prove the damper has failed, so first check the floor, leveling feet, load size, and suspension springs. Match the ...Read morereplacement to the complete model because mounting ends and force ratings can differ. Disconnect power and water before opening the cabinet. Keep the tub supported, note each fasteners position, and avoid pinching hoses or wires during reassembly. Run an empty rinse and spin cycle to check for leaks, noise, and steady movement.

This is an individually sold front shock absorber designed for use with Samsung dryers. Shock absorbers are used to distribute the weight of the dryer drum evenly and ensure that the different bumps and bounces that occur during the drying cycle are smoothed and counter acted. A broken shock absorber is noticeable by the amount of noise y...Read moreour dryer will make during operation. Replacing this absorber and its rear counterpart may even be necessary to the lifespan of the other dryer parts, so be sure to inspect both absorbers before ordering. To install this OEM shock absorber in your dryer, you will need to disassemble the dryer, which requires a screwdriver and wrench.

This is an outer seal clamp for the washer door boot of your Samsung washing machine. This clamp tightly seals the boot of the drum within the door of the washer to prevent leaks. This clamp is made of metal and features a spring in the middle, but over time can be worn down or break, and result in water leaking out of the washing machine...Read more and into your home. Replacing this clamp will require a screwdriver, pliers, and safety gloves. This clamp is an OEM part that comes individually, without any other parts or accessories.

This is a door switch assembly designed for Samsung washing machines. This door switch assembly is used to latch and lock the door shut before the washing cycle commences and communicates with the control board when that is done. If your washer door is not locking or latching properly, the door switch is likely bad or broken and will need...Read more to be replaced. To replace this assembly, you will need a flat-head and Philips-head screwdriver. This part is a genuine OEM switch assembly and is sold individually, without any wire harnesses or securing screws.

One solenoid valve for hot water

This boot seal, also known as a tub diaphragm, creates a waterproof seal between the door and the drum in your front-loading washer, preventing water from leaking out during the wash cycle. You can find it around the door opening, and it is visible when the door is open. Please note that this seal is sourced directly from its original manufacturer and is sold separately from the outer seal clamp.

Shipping bolts are installed through the back of the washing machine, and hold the wash tub and basket in place while your washer is being transported. The tub suspension holds the tub correctly in place during the wash, rinse, and spin cycles. If this suspension is damaged during shipping, the tub can shake and move, tilt to one side, or...Read more spin incorrectly. This could lead to the suspension or motor failing. When moving your washer, it is suggested that you insert the shipping bolts back into place before moving the machine. This part is also called a washer transit bolt. Remember that this part is sold separately, and to check your model to see how many you require.

The drain pump removes water from the washer during the drain portion of the cycle.