EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

WED8300SW2 Whirlpool Dryer - Instructions

All Instructions for the WED8300SW2
91 - 105 of 948

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer stopped heating
7 of 8 people found this instruction helpful.
  • Joseph from Austin, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple t o get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.
Was this helpful?
Thank you for voting!
My dryer conked. Would not turn on, but before that happened it was taking way too long to dry the clothes and the dryer would stop in the middle of a cycle.
7 of 9 people found this instruction helpful.
  • brenda from Newman Lake, WA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Went on this website and found a story that was similar. I ordered the parts which arrived quickly and I replaced the Thermal Fuse and heating element and it was fixed! The whole repair cost me $24.88! Way cheaper than calling a repair man.
Heater thing was part # 3387134
and the fuse was 3392519
Was this helpful?
Thank you for voting!
Annoying loud metal to metal screeching noise.
6 of 6 people found this instruction helpful.
  • Ricardo from ARBUCKLE, CA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Took the front part of the dryer out, released tension on the idler pulley, took the drum out, and remove the old drum seal. Make sure you remove the old adhesive with sandpaper or wire brush. Put the new adhesive on the seal, not on the drum. Adhesive is very runny. Seal may need to be stretched to fit the drum. Set the seal on the drum , let sit a few minutes. Put everything back together.
Was this helpful?
Thank you for voting!
Lens melted because paper got behind the lens and was heated by the lamp.
6 of 6 people found this instruction helpful.
  • Chris from Valley Stream, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
1 screw to replace.
Was this helpful?
Thank you for voting!
F01 Error Code
6 of 6 people found this instruction helpful.
  • Carrie from WEXFORD, PA
  • Very Easy
  • Less than 15 mins
  • Screw drivers, Socket set
At first, my dryer would just make a clicking noise but would not start. After some research, I unplugged it to try to 'reset' it and after that, I noticed the F01 error. Some quick research on the internet you can find the source of the error is a failed machine board. Some DYI people soldered the part where the connection broke but, I chose to just buy the new part. I was pretty confident where the error was and did not want to waste time and the cost of a repair man visit. I followed the instructions on the most thorough YouTube video and removed the top of the dryer, took pictures of the control board wires and began the removal process. The insertion fo the new board took about 1 minute. All in all, the physical work took my husband and I about 10 minutes. Research was about an hour and I had the part shipped overnight. This website has saved me hundred of dollars and lots of wasted time trying to find a repair man when Covid has made it difficult to get anyone to your house. Our washer sprung a leak during the initial lockdown and we were able to fix that ourselves as well.
My only comment about the part is that the chime at the end of the cycle is very different. I have yet to find out if I can change that but it is not too bothersome.
I love this website and its products!
Was this helpful?
Thank you for voting!
Dryer would start and then stop after a few minutes, eventually it completely stopped.
11 of 21 people found this instruction helpful.
  • Keith L. from San Diego, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Wrench (Adjustable)
After determining that the dryer motor was the issue, I wrote down the part number and logged on to partselect.com website.

I input the number into the search box and there was the exact motor I needed.

The correct part showed up in a timely manner and the pricing was very fair.

I disassembled the dryer, removed the old motor and reinstalled the new motor within about 30 minutes.

Key point was to read the instructions first and then reconnect the wiring to the new motor. The new motor has the switch install in a different spot on the motor so be careful to follow the instructions but, the instructions were very clear and connections were very simple.

I also did some preventive maintenance while I was in the unit by cleaning out any remaining lint from the heater unit and surrounding areas, that took about 30 minutes. Reassembling was a snap and I turned on the gas, plugged it in and........SUCCESS! Total time of repair and cleaning was about an hour.

I had a load of laundry ready to go and put the new motor right to work. It has been non-stop drying and thanks to Part Select for getting everything right the first time. It has been a positive experience and I will tell others about the website if they have similar problems. Thanks again for a success story and dry clothing.
Was this helpful?
Thank you for voting!
No heat
6 of 6 people found this instruction helpful.
  • Richard from HAGERSTOWN, MD
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Took the back off the dryer. Found heating element unhooked the electrical connectors to the element,the high temp thermostat and the fuse backup. Opened the front kick plate, took the casing with element, ht thermostat and fuse bu out. Changed all three parts and reinstalled them. Turned on dryer and had heat. Been working great ever sin ce.
Was this helpful?
Thank you for voting!
Broken Belt
7 of 9 people found this instruction helpful.
  • Ken from LOMBARD, IL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Started at the top by laying back the control panel, then I removed the top panel, then the front panel, next the drum and the broken belt. before I put it back together in reverse order, I vacuumed the inside of the dryer and the exhaust vent
Was this helpful?
Thank you for voting!
Dryer does not heat but blows only cold air
6 of 6 people found this instruction helpful.
  • kevin from RENTON, WA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Pulled the lower front panel located thermal switch pulled 2 wires removed 2 small bolts pulled switch out set meter to ohms scale and tested between the 2 terminals it hailed the test I reversed for installation of new switch
Was this helpful?
Thank you for voting!
The door will not latch tightly.
9 of 16 people found this instruction helpful.
  • John from Syracuse, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I replaced both the door strike and the female portion. The door still does not close tightly. Heavy, wet items also knock the door open.
Was this helpful?
Thank you for voting!
Dryer would not start.
7 of 10 people found this instruction helpful.
  • Rebecca from Scarsdale, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unplug dryer from mains. Remove the back of the dryer. Thermal fuse is located on the left hand side near the bottom as you face the back of the dryer. Remove fuse and connect new fuse. Never repaired an appliance before and this was so easy!
Was this helpful?
Thank you for voting!
Drive pulley broke. Looked like clip holding it on broke and pulley was running crooked.Belt was squealing some a couple of weeks before it broke.
6 of 7 people found this instruction helpful.
  • Mark from Sheffield, PA
  • Easy
  • 30 - 60 mins
  • Socket set
Removed top and back covers. Placed new pulley and retaining clip in place. I had to remove a couple of drum supports to put belt on. Probably didn't have to remove top.
Was this helpful?
Thank you for voting!
Broken Motor Pulley
7 of 10 people found this instruction helpful.
  • Mark from PELHAM, MA
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Socket set
Removed back panel of the dryer-reached my hand to the back of the motor shaft, put 7/16 wrench on it to hold the shaft while I removed the broken pulley with pliers. Very easy fix-the tech on Utube took the entire dryer apart totally unnecessary. If that is what the factory tells its tech"s to do its no wonder why the labor charge woul d be thru the roof.
Was this helpful?
Thank you for voting!
The belt you sent was too short
6 of 7 people found this instruction helpful.
  • Larry from Middlebury, IN
  • Very Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
I disassembled the dryer, replaced the pulley (which was noisy), and the belt.reassembled, only to find out that the drum would not turn freely. checked all my procedures and kept having the same problem. Finally after 3 frustrating hours, I took the back off and noticed that idler arm was tight against the motor shaft, because the too s hort belt didn't allow for the clearance needed. Had too take everything apart ,another hour, went and found one at our local repair shop, reinstalled everything , after another two hours runs fine. would appreciate a refund. And please check your part numbers in the future. Would hate to have someone else go through what i experienced.
Was this helpful?
Thank you for voting!
couldn't get the wire connection anywhere after we bought the heating element.
6 of 8 people found this instruction helpful.
  • Betty from Erie, PA
  • Really Easy
  • 15 - 30 mins
  • Socket set
we received the two heating element wires in 3 days and connected the heating element with no problem works great.
Was this helpful?
Thank you for voting!
All Instructions for the WED8300SW2
91 - 105 of 948