UT10519 Homelite Chainsaw - Parts

The carburetor gasket fits between the carburetor and the carburetor plate and helps to provide a seal. This is a genuine Homelite and Ryobi replacement part used in chainsaws. It is available as an individual replacement part. A socket set, a set of pliers, and a screwdriver might be helpful during the installation of this part. This part is made out of a thin material and will need to be replaced if it breaks.

This is a genuine replacement part manufactured for use with chainsaws. The throttle cable is the linkage between the throttle trigger and the carburetor. The small connectors at the end of the cable can break or wear out, and replacing a broken cable is an easy way to extend the life of the chainsaw. This throttle cable is sold as an individual replacement part.

This replacement ignition coil also known as a magneto is a genuine OEM part. It is specially produced for Homelite and Ryobi chainsaws. It plays an important role, because it producing pulses of high voltage for the spark plugs. It is made out of metal with a rubber insulated wire and a spark plug boot. Please note replacing this module...Read more would differ based on your unit, however the basic steps would be the same. To complete this repair you will need screwdriver and a wrench set. • Remove the housing/covers from the unit • Remove the spark plug • Bind the cylinder • Remove the air filter cover and side cover • Remove the throttle cable from the carburetor • Disconnect the wires • Remove old ignition coil • Install new ignition coil • Set the gap • Reassemble and test the unit

This is a genuine OEM sourced part that is intended to be used with Homelite chainsaws and Ryobi pruners and chainsaws. The plastic oil cap is used to cover the oil tank fill spout to prevent spills and to stop contaminants from entering the tank. The cap includes the tether that connects the cap to the tank and the cap is priced as a single item.

The adjustment knob attaches to the clutch cover ring. Keep in mind that this part is sold individually and is made out of plastic. This is an OEM part sourced directly from the manufacturer and used in chainsaws made by Homelite. A screwdriver might be necessary during the installation of this part. It will need to be replaced if it becomes broken.

This is a genuine manufacturer-approved replacement part which is specially designed for Homelite chainsaws. It helps to provide a tight fit between connected component allowing them to rotate with minimum friction. If the bushing is damaged or is missing, this will provide an identical replacement for the original hardware that was insta...Read morelled on a new unit. Refer to the appropriate diagrams for your model to ensure the proper replacement procedure. Note, one durable metal bushing is included. You will need a wrench set to perform this repair.

This replacement clutch assembly is utilized on Homelite and Ryobi chainsaws. It is a genuine OEM sourced item, not an aftermarket equivalent. A centrifugal clutch connects two concentric shafts with the driving shaft nested inside the driven shaft. Keeping an eye on equipment performance will determine when the centrifugal clutch require...Read mores replacement. Please note the clutch drum, spacer and washer are all sold separately. This clutch is made from durable metal material and it is sold individually. To complete this repair you will need a screwdriver and pliers.

This metal OEM wire clamp is a type of fastener that holds hoses or cables together and keeps them from moving while your machine is operating. It is mostly found in lawn equipment to attach its fuel line to the filter. You can tell that the metal clamp is broken if the parts it was securing has become loose or has fallen off. When this h...Read moreappens, your equipment may start leaking and can pose as a safety hazard. To remove the wire clamp, you need a pair of pliers. Grip onto a broken clamp before twisting it counterclockwise to release it from your machine. This item is sold separately.

This replacement switch is an authentic item that is supplied directly from original equipment manufacturer for use with Homelite and Ryobi equipment. It is the key component of the tool handling on/off operations. Over time either mechanical or electric components of the switch may begin to fail eventually requiring replacement. Please note this high quality plastic body switch is sold individually.

This is a genuine part from original manufacturer, compatible with many Ryobi and Homelite chainsaws. An E-ring is a circular metal piece, notched with one open side. They are designed to clip into place on a shaft in order to keep other parts secured. Sold individually.