UT10519 Homelite Chainsaw - Overview

This is a genuine OEM replacement part, it is made out of Metal with Fabric Filter Material. It is sold individually and is used on a variety of Lawn and Garden Equipment. This is an in-tank fuel filter which makes sure that the fuel delivered to the engine is free of any debris or contaminants. It will over time become clogged and restrict the fuel getting to the engine so it will need to be replaced.

This is an authentic OEM sourced replacement screw designed for use with chainsaws. It helps to secure the muffler assembly. This part is made out of metal and it is sold individually. You would need a wrench to tighten/loosen this screw.

This is an OEM replacement part,it is sold individually. The purpose of the Air Purge Bulb is to purge all of the air from the carburetor. It then brings fuel up through the fuel line in the tank into the carburetor. Once the carburetor is full of fuel the Bulb will force the excess fuel back into the tank through the fuel return line. ...Read moreOver time the bulb will loose it elasticity or begin to crack, it will need to be replaced at this time.

This is an authentic OEM sourced replacement part is designed for use with Homelite chainsaws. The purpose of the tension nut serves to tighten and secure the chainsaws clutch cover lock knob. It is made out of metal with plastic and it is sold individually. This part is a merged assembly of old part# 518769001 (Cover Knob) and 678618002 (Tension Nut).

This is a genuine OEM replacement part, it is sold individually. The purpose of this filter is to keep dirt and other small particles from entering the carburetor and engine and causing internal engine damage. Once this type of filter gets clogged or dirty it should be changed (Not Cleaned). This is to prevent restricted air flow and foreign matter from entering the engine.

This is a Manufacturer Sourced replacement part for Lawn and Garden equipment. This item is Metal an is Sold Individually. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt. This Locking Nut has multiple uses based on your tool. You would need a Wrench to tighten or loosen this Hex Nut.

Genuine OEM replacement part, this item is sold individually. The purpose of the 631036001 Guide Bar Plate is to assist in keeping the Chainsaw Blade inline. Also with out this plate, if the chain was to come of the chain bar, this part would help keep the housing of the Chainsaw from being damaged.

This genuine OEM sourced replacement part is designed for use with gas chainsaws. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. If the engine won't start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carburetor. Pull...Read more the starter rope. If the engine starts and then quickly dies, the carburetor is likely the problem. This carburetor has a metal body and it is sold individually. To complete this repair you would need a screwdriver. • Remove the air filter cover • Remove the air filter base • Remove the throttle cable • Remove the fuel lines • Remove the carburetor • Install the new carburetor • Reinstall the fuel lines • Reinstall the throttle cable • Reinstall the air filter cover

This steel OEM part is used in Homelite and Ryobi chainsaws. The sprockets connect to and control the saw chain. This is a commonly replaced part because of its high-wear function. Please note that washers and e-rings are sold separately.

Authentic manufacturer approved replacement bolt made for use with string trimmers and chainsaws. This is a standard hardware with multiple uses based on your tool. Please refer to specific diagrams for correct application. This bolt has a hex socket head which requires a hex key/allen wrench for installation. It is sold individually.

The carburetor gasket fits between the carburetor and the carburetor plate and helps to provide a seal. This is a genuine Homelite and Ryobi replacement part used in chainsaws. It is available as an individual replacement part. A socket set, a set of pliers, and a screwdriver might be helpful during the installation of this part. This part is made out of a thin material and will need to be replaced if it breaks.