TGS326RD2 Estate Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven handle broke
2 of 2 people
found this instruction helpful.
-
Jim from CAMDENTON, MO
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
new handle arrived black for white oven - screws did NOT fit new handle- glass came off the door when removing old handle
Was this helpful?
Thank you for voting!
Oven would not maintain Heating
2 of 2 people
found this instruction helpful.
-
Cheryl from WEST JORDAN, UT
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
Following details from the installation video, after removing the main gas line and the two output lines I removed the four screws that removed the valve but found it was easier to remove and install the new one if I first removed the oven burner(it made for lining up the valve nozzle to the burner easier) from the inside, 3 wires attach
... Read more
on the side towards the stove taking one wire from the old valve and putting it on the new valve in the same place. Everything went back together just fine, I did have some problem with tightening one of the two gas lines for the output and found I just had to keep tightening it a little until there were no bubbles appearing when I applied soapy water to the connections, other than that it was very straight forward.
Read less
Was this helpful?
Thank you for voting!
Didn’t work
2 of 3 people
found this instruction helpful.
-
James E. from WAYNE, MI
- Really Easy
- 30 - 60 mins
-
Screw drivers
Took out old one but electric hook up fell in the hole had to fish it out also dropped a screw in the hole could’ve find it used a different one
Was this helpful?
Thank you for voting!
I was trying to remove the oven door so I could clean the glass. Spills had run down between the layers of glass.
3 of 6 people
found this instruction helpful.
-
Karen from Oklahoma City, OK
- Difficult
- More than 2 hours
-
Screw drivers
This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proce
... Read more
eded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.
Read less
Was this helpful?
Thank you for voting!
temp level uneven
2 of 3 people
found this instruction helpful.
-
Paul from HARMONY, MN
- Very Easy
- 15 - 30 mins
after watching the video, installed the temp sensor. Super easy
Was this helpful?
Thank you for voting!
the oven temperature was not working right. I installed a new oven sensor. Works get now
3 of 6 people
found this instruction helpful.
-
Rosalind from APOLLO, PA
- Very Easy
- 15 - 30 mins
-
Screw drivers
Watch the video...
Was this helpful?
Thank you for voting!
last oven bottom was ruined by melted and burnt plastic
2 of 3 people
found this instruction helpful.
-
Dennis from Missouri Valley, IA
- Really Easy
- 15 - 30 mins
-
Screw drivers
took out old oven bottom by removing 2 screws, placed the new oven bottom in place put the screws back in and was done.
Was this helpful?
Thank you for voting!
LIght switch on oven door was broken
2 of 3 people
found this instruction helpful.
-
James from Sequim, WA
- Easy
- Less than 15 mins
-
Screw drivers
Turned off power at circuit breaker. Removed 4 phillips screws from area over oven door. Pulled control panel out and twisted to clear top rail. Pulled two wires off of old switch.Pulled old switch through panel. Inserted new switch. Attached the two wires to new switch. Replaced panel and inserted four screws. Turned on power - it
... Read more
works!
Read less
Was this helpful?
Thank you for voting!
Broken drawer glide
1 person
found this instruction helpful.
-
karen from Thornton, CO
- Really Easy
- Less than 15 mins
-
Screw drivers
Used a phillips head screwdriver to remove the single screw holding the part in place and put the new one on. Finding the part on this site was a breeze and it arrived quickly. A first rate experience all around.
Was this helpful?
Thank you for voting!
Worn/Bulb Socket
2 of 4 people
found this instruction helpful.
-
JOSEPH from COON RAPIDS, MN
- Really Easy
- Less than 15 mins
-
Screw drivers
It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.
Was this helpful?
Thank you for voting!
screw came off
1 person
found this instruction helpful.
-
Sandeep from EDINA, MN
- Very Easy
- Less than 15 mins
-
Screw drivers
very expensive to buy the part but just tighten the screw intot eh predefined place.
Was this helpful?
Thank you for voting!
slides on lower drawer were broken
2 of 4 people
found this instruction helpful.
-
Leona R from Louisville, KY
- Really Easy
- Less than 15 mins
-
Screw drivers
I used a phillips screwdriver and replaced the part with one screw.Very easy and replaced my lower drawer under my oven,it tool about three to five minutes at the most and my drawer works fine now.Thanks for the instruction video on line, it really helped.
Was this helpful?
Thank you for voting!
Broken slide segment on drawer glide
1 person
found this instruction helpful.
-
Linda from WATERTOWN, WI
- Very Easy
- 15 - 30 mins
-
Screw drivers
Luckily, I bought 2 glides right away, as the 2nd one broke while I repaired the 1st one. It was a straight forward screw in the parts using a Phillips screwdriver.
Was this helpful?
Thank you for voting!
oven light kept burning out instantly
1 person
found this instruction helpful.
-
David from ENID, OK
- Easy
- 15 - 30 mins
-
Screw drivers
Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The ... Read more part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The ... Read more part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
Read less
Was this helpful?
Thank you for voting!
Rear drawer slide was broken.
1 person
found this instruction helpful.
-
David from Mauldin, SC
- Really Easy
- Less than 15 mins
-
Screw drivers
Undid one screw. Removed the broken slide. Replaced with new slide an fastened with the existing screw. Problem solved.
Was this helpful?
Thank you for voting!