TGS326RD2 Estate Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven stopped heating, error message stated heating element
3 of 3 people
found this instruction helpful.
-
Lana from WATERVILLE, ME
- Really Easy
- Less than 15 mins
-
Screw drivers
Very easy. Pulled the stove away from the wall. Used a screw driver to remove the two nuts to release the heat sensor, disconnected the wire, removed the sensor. Inserted the new sensor, plugged back into the circuit. put the two nuts back.
Beware, if the first time you put the oven on, if the error message comes back up (mine did ... Read more ) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.
Beware, if the first time you put the oven on, if the error message comes back up (mine did ... Read more ) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.
Read less
Was this helpful?
Thank you for voting!
Oven Temp inaccurate
3 of 3 people
found this instruction helpful.
-
David from BURNSVILLE, MN
- Really Easy
- 15 - 30 mins
-
Screw drivers
I watched the repair video on this site and another on YouTube before I started. The rear panel has a different shape and two additional screws on the bottom edge. The power clip was easy to manipulate.
This was an easy fix for a seventy year-old like me!
This was an easy fix for a seventy year-old like me!
Was this helpful?
Thank you for voting!
replace bake ignitor ; flame spreader removal difficulty
3 of 3 people
found this instruction helpful.
-
Steven from SAN ANSELMO, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
As the 2 screws in the front of the flame spreader didn't screw into anything , and made getting the flame spreader very difficult to remove, once I got the flame spreader out , I did cut off the screws so future install & removal would be easy. I had to hacksaw the screws off , as the screws are otherwise impossible to remove. The screw
... Read more
s were damaging the oven metal sheet work during first removal ! Otherwise the new bake ignitor install would have been a very quick 20 minutes. Also I watched u-tube bake ignitor install & oven door remove videos, which were extremely helpful.
Read less
Was this helpful?
Thank you for voting!
WOULD NOT HOLD DESIRED BAKE TEMP
3 of 3 people
found this instruction helpful.
-
WILLIAM from SAINT JOSEPH, MI
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
REMOVE BOTTOM OVEN PAN. REMOVE GAS DEFLECTOR. REMOVE GAS TUBE. UNPLUG WIRE. REMOVE TOP AND BOTTOM SCREWS ON IGNITER. REPLACE IGNITER AND REATTACH IGNITER SCREWS. RE-INSERT IGNITER PLUG. REPLACE GAS TUBE AND DEFLECTOR. REPLACE OVEN BOTOOM PAN.
Was this helpful?
Thank you for voting!
Gas oven would shut off mid cook
3 of 3 people
found this instruction helpful.
-
Glenn from ROANOKE, TX
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Removed grills. Removed bottom plate.
Removed flame shield.
Removed igniter, 2 hex head screws. Bottom one is a bit awkward. Disconnected wire. Installed new igniter. Careful not to drop stuff in the hole. Like a socket. I did
Removed flame shield.
Removed igniter, 2 hex head screws. Bottom one is a bit awkward. Disconnected wire. Installed new igniter. Careful not to drop stuff in the hole. Like a socket. I did
Was this helpful?
Thank you for voting!
Oven lamp socket had broken center electric tab - failed.
3 of 3 people
found this instruction helpful.
-
Stan from FLAT ROCK, NC
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
1993 model oven, built in wall model, so didn't to remove oven for the normal rear access to replace the lamp socket. As someone else posted, replacement can be done from inside the oven -- BUT the socket removal was more complex than just 'twisting it out.' But below worked! (1) Turned off oven power at circuit breaker panel. To facilit
... Read more
ate working in the oven compartment, removed oven door (2 screws on back of door), raised the over door almost closed, put 2 large nails through the hinge holes when they lined up. Lifted the door out (heavy ~20-25 lbs) and put aside. (2) Put work light inside oven. (3) unscrew glass socket lens and the bulb). (3) Using inspection mirror, studied the inside of the socket to determine that its lock tab type and locations -> were on left and right sides of the socket. These tabs needed to be bent in, but they were each held out by a small circumferential length of think metal, a tab about 3/16" x 3/8". These small tabs could be moved/positioned by just finger friction, with a little start with a screwdriver tip on their edge! I got an end positioned to put sharp screwdriver under that end, then pried it (bent it) inward a short distance. Enough to use needle-nosed pliers to pull it completely out - came fairly easily. Repeated on other side of socket. (4) Then, with pliers, bent each of the 4 locking tabs inward a short distance, Used sharp tool to get one socket edge lifted a small amount; then use mini-pry bar and screwdriver to gently pry around the socket in steps, working evenly around its edge. At about 3/8", it was free. Lifted it inward gently so as not to damage the insulation of the 2 wires attached to its rear. Noted the direction of the wire tabs was straight up (keep same orientation on new socket). (5) Needle-nosed pliers on each connector to gently work the connectors off their socket tabs. Note one tab is larger than the other. Keep the wires inside the oven compartment. Don't damage the insulation. (6) Pushed the wire connectors onto their respective new socket tabs. Aligned socket with the tabs upward, and inserted it, careful to nurse the wires back into the oven wall hole; press socket into the hole, pushing it in evenly and firmly until flush. (7) Pushed in the new type bulb that came with new Socket. Turned on power, and light came on. (8) screwed on new glass cover. (9) Lifted oven back onto the hinge prongs. (easier with two people to get the prongs aligned and into their door slots.) Worked door left and right to get it to lower down fully. Removed nails, lowered door, and put its 2 screws back on. (10) Poured a glass of wine.
Read less
Was this helpful?
Thank you for voting!
oven not keeping correct temp and sometimes would not relight when temp went dropped.t
3 of 4 people
found this instruction helpful.
-
Gary from PLUM CITY, WI
- Really Easy
- 30 - 60 mins
-
Screw drivers
Slid oven out and took back shield off unplugged sensor took bracket screw out replaced sensor with new one.
Was this helpful?
Thank you for voting!
Igniter stopped sparking.
3 of 4 people
found this instruction helpful.
-
David from EDEN PRAIRIE, MN
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I ordered the exact replacement igniter through the website. I removed the oven bottom plate and the flame spreader to gain access to the igniter/burner assembly. I removed the burner from the oven to access the mounting bolts for the igniter. I replaced the assembly into the oven and reconnected the igniter wire and it was set!
Was this helpful?
Thank you for voting!
Range control knobs were broke
3 of 4 people
found this instruction helpful.
-
Donovan from RIVERBANK, CA
- Really Easy
- Less than 15 mins
-
Pliers
The parts I got were exactly like the original knobs and were a breeze to snap on. Range working great again . The wife is happy again lol
1. Removed old knobs and the adapter piece with pliers ( I tried using cheap universal knobs from Lowe’s first that were garbage)
2. Push the new knobs onto the shaft and voila. P ... Read more erfect fit and range looks new again. Replaced all 4 on my black whirlpool gas range
1. Removed old knobs and the adapter piece with pliers ( I tried using cheap universal knobs from Lowe’s first that were garbage)
2. Push the new knobs onto the shaft and voila. P ... Read more erfect fit and range looks new again. Replaced all 4 on my black whirlpool gas range
Read less
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people
found this instruction helpful.
-
Yafa (and David) from Bothell, WA
- Easy
- Less than 15 mins
-
Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
Broken Door Handle
2 of 2 people
found this instruction helpful.
-
Daniel from BROOKLYN, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove the side covers. Remove the 2 screws on the back side of the door, hold on to the glass and front panel, they will fall out. remove the 2 screws holding the handle. Put the new handle in place and insert screws, note the old handle had metal inserts that are threaded, the new does not. Had to push very hard and let the screws bite
... Read more
into the plastic.
Read less
Was this helpful?
Thank you for voting!
oven would not completely heat up, only heating to about 150 degrees Temp.
2 of 2 people
found this instruction helpful.
-
Isaac from MATTESON, IL
- Very Easy
- 15 - 30 mins
-
Screw drivers
contracted a repair service person
Was this helpful?
Thank you for voting!
Corroded/greasy bottom oven tray
2 of 2 people
found this instruction helpful.
-
Robert Ruth from FERNDALE, WA
- Very Easy
- 15 - 30 mins
-
Screw drivers
Loosened two screws and removed tray, very simple. Replaced new tray and adjusted screws to hold tray. Easiest part was finding new tray part number and ordering replacement using online parts diagram.
Was this helpful?
Thank you for voting!
Oven not reaching temperature
2 of 2 people
found this instruction helpful.
-
Marsha from Clermont, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place
Was this helpful?
Thank you for voting!
Stove would not light due to faulty electronic ignighter
2 of 2 people
found this instruction helpful.
-
Victor from SAINT PETERS, MO
- Really Easy
- 30 - 60 mins
Very easy repair, simply remove old ignighter and install new one. Take pictures if you need help remembering where everything goes.
Was this helpful?
Thank you for voting!