- Home
- TFX22PRXDBB
- Instructions
TFX22PRXDBB General Electric Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
door not closing corecyly
1 person
found this instruction helpful.
-
steve from winthrop harbor, IL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
took top bracket off--then removed door--took
bottom bracket off bottom of door and replaced
door closing cam and reasembled---a piece of
cake
bottom bracket off bottom of door and replaced
door closing cam and reasembled---a piece of
cake
Was this helpful?
Thank you for voting!
Door no longer closed on it's own and would not stay closed all the time
1 person
found this instruction helpful.
-
Dale from Hot Springs, AR
- Easy
- 15 - 30 mins
-
Nutdriver
First a big thank you to PartSelect.com. I read the stories posted by others before ordering the parts and found out that I probably needed 2 of these cams. So I followed the advice of others and ordered 2 cams. I'm really glad I did because once I got the door off I discovered both were broken up real bad. Maybe you guys should think abo
... Read more
ut offering them as a set?
Anyway the repair was fairly easy, except for the bottom cam which was revited to the bottom bracket. Again, thanks to the other stories about repairs with this part I was already expecting this. So the repair went like this. I removed the door by unscrewing the hinge on top(1 screw and 2 bolts). Took the door off and laid it on its side. Removed the bottom bracket( 2 bolts). Used a drill to drill out the rivit. Used a spare screw/nut that I had in a tool box to fasten the cam to the bracket. Put it all back together and I was done. The biggest challenge was figuring our if I needed 2 cams,so with the advice of others on your site, my repair was a snap.
Anyway the repair was fairly easy, except for the bottom cam which was revited to the bottom bracket. Again, thanks to the other stories about repairs with this part I was already expecting this. So the repair went like this. I removed the door by unscrewing the hinge on top(1 screw and 2 bolts). Took the door off and laid it on its side. Removed the bottom bracket( 2 bolts). Used a drill to drill out the rivit. Used a spare screw/nut that I had in a tool box to fasten the cam to the bracket. Put it all back together and I was done. The biggest challenge was figuring our if I needed 2 cams,so with the advice of others on your site, my repair was a snap.
Read less
Was this helpful?
Thank you for voting!
Door wouldn't close with out help.
1 person
found this instruction helpful.
-
Rodger from Brunswick, OH
- Really Easy
- 15 - 30 mins
-
Socket set
Removed four screws at bottom of door, while someone held the door in place replaced the upper cam (there are two) applied some silicone plumbers lube between the mating surfaces and tightened it up. Works like new bottom cam was only slightly worn. P.S. Remove everything from the door first.
Was this helpful?
Thank you for voting!
The refrigerator door would no stay closed
1 person
found this instruction helpful.
-
Ken from Fountain Valley, CA
- Really Easy
- 15 - 30 mins
-
Socket set
I was set to buy a new magnetic seal to hold the door closed, when I looked it up on PartSelect I saw the recommendation that the problem might be the door closing cam.. I check it with a mirror and sure enough the cam had broken and the door sagged about 1/4 inch. I then followed the instruction and removed the top hinge, lifted the door
... Read more
off and replaced the cam. I did need two and the one attached to the lower hinge had to be drilled out and a new screw and nut attached to hold the cam. It was simple to do, I would recommend selling the door closing cam be sold in pairs with a #10 1/2 inch long screw with lock nut.
Read less
Was this helpful?
Thank you for voting!
Door closer cam riser
1 person
found this instruction helpful.
-
C. Robert from Sandusky, OH
- Really Easy
- 15 - 30 mins
-
Socket set
I blocked the door up with one 2X4 Then removed the lower hinge, installed the closing cam. Then I found that I needed one more closing cam that I didn't order the first time. This other one mounts to the lower section of the door and both cams set together. Re-ordered another cam. When it came in I installed it. Between ordering both
... Read more
parts I had them both in three days. The best to Parts Select
I now know where to buy my parts if needed again.
Thanks
Bob
Sandusky, Ohio
I now know where to buy my parts if needed again.
Thanks
Bob
Sandusky, Ohio
Read less
Was this helpful?
Thank you for voting!
Frost buildup in freezer by the ice maker
1 person
found this instruction helpful.
-
Alex from Cary, NC
- Really Easy
- 15 - 30 mins
-
Screw drivers
Replaced dispenser door flapper by following the do it yourself video in this site. It was really easy. Just be careful when removing the dispenser black bezel. I broke one of the little tabs when taking it off.
Was this helpful?
Thank you for voting!
drum light burned out
1 person
found this instruction helpful.
-
Stephanie from DENVER, CO
- Really Easy
- Less than 15 mins
removed the bulb from the package unscrewed the old bulb & screwed in the new bulb.
Was this helpful?
Thank you for voting!
Had a drip which filled up the tray and leaked on the floor from water dispenser
1 person
found this instruction helpful.
-
Rudy from CITRUS SPGS, FL
- Very Easy
- 15 - 30 mins
-
Screw drivers
There are Great videos on YouTube!!! Turned off power,Removed trim ring, Pushed a philips head screwdriver in one of the holes underneath the electrical panel with the selector push buttons. This releases the electrical panel. There are Three wire sets with plugs. I removed the plugs and took the electrical panel out. Removed four Phillip
... Read more
s head screws and pulled out the big paddle switch. This then exposes the flapper. Replaced flapper with new one and reassembled everything. When I had everything apart, I cleaned with window cleaner. It was pretty moldy from the water leaking. Turned power back on and tested everything to make sure I didn't mess anything up. Works great
Read less
Was this helpful?
Thank you for voting!
Ice Maker Leaking
1 person
found this instruction helpful.
-
Carl from SAN MARCOS, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
Researched on internet/you tube; ordered part, and did the repair. Easy to do and saved the cost of a service call.
Was this helpful?
Thank you for voting!
Flapper was worn and misshapen allowing warm air in freezer, ice cubes to melt and drip and impairing function of ice dispenser. Frost formed in ice dispensing chute also.
1 person
found this instruction helpful.
-
Mark from HAYMARKET, VA
- Easy
- 15 - 30 mins
-
Screw drivers
Followed the online video. Unplugged refrigerator, removed trim piece, lifted control board cover, removed 4 screws retaining circuit control board and removed the 3 connectors from the control board. Located flapper and removed by using small flat tip to take tension off flapper connectors. Helper held flash light to illuminate flappe
... Read more
r connectors. Reversed procedure. New flapper seals well and cured problems. Circuit board was a bit different than one in video, but still had the 3 connectors. Marked each connector with grease pencil at top edge to ensure correct reconnection. Should note how wires are threaded around circuit board to ensure they are tucked back in correctly in reassembly. Remove trim piece carefully. I broke 2 of the 8 plastic pins that hold trim on. May be due to age of unit as they were brittle. 6 pins still hold trim piece flush.
Read less
Was this helpful?
Thank you for voting!
The door closing cam had broken up.
1 person
found this instruction helpful.
-
J Barry from Sparta, NJ
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Socket set
The old cam had broken and was on the floor. I ordered one new cam. I should have been told to order at least two, I did not know they worked in pairs. So I had to re-order, I ordersed four, I was able to see that the other (freezer door has cracked cams) door will soon need replacement of the cams. I had trouble installing the new pa
... Read more
rt because the rivit also needed to ba replaced. I did a "Rube Goldgerg" to get the new part to sit properly. I drilled the hole open a little and forced the part into place. All is well. Thank you very much!
Read less
Was this helpful?
Thank you for voting!
Warm air enters ice dispenser on door
1 person
found this instruction helpful.
-
J Stephen from BETHESDA, MD
- Really Easy
- 30 - 60 mins
-
Screw drivers
Replaced flapper. Followed the video. The lamp caused the removable plastic bracket (which supports the control panel and the ice chute) to fuse with the plastic frame in the door. Eventually broke the fused plastic, removed the bracket, and filed the rough broken plastic before reassembly.
Was this helpful?
Thank you for voting!
Original part cracked allowing crushing fingers to grab plastic guide jamming it.
1 person
found this instruction helpful.
-
Barry from SUN VALLEY, CA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Part attaches to metal plate near crushing fingers which attaches to ice holding bin. Remove about 6 screws total on each side of plate. You must disassemble the auger & other parts so you can reassemble it in the proper order. Not many parts but i always take pics to cut down on time. New part is at the other end of the auger and acts a
... Read more
s the holde of the auger shaft. Picture a crankshaft with a bearing on each end so the auger rotates between new part and the other end of auger shaft. That's it.
Read less
Was this helpful?
Thank you for voting!
rust ice auger
1 person
found this instruction helpful.
-
Anthony from OKLAHOMA CITY, OK
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
the previous left behind a side by side, everything worked however the auger in the ice bucket was a little rusty. I wish that I could say it was all me but the truth of the matter was the videos on file.
They were nicely done and easy to follow as I took the unit apart and replaced the auger in about 30 minutes. Thanks for al ... Read more l your help in part look up.
They were nicely done and easy to follow as I took the unit apart and replaced the auger in about 30 minutes. Thanks for al ... Read more l your help in part look up.
Read less
Was this helpful?
Thank you for voting!
Watched video on flapper assembly replacement looked real ready. Video failed to mention ice dispenser trim was glued in place . Had to buy real small paint scrapper that would fit in dispenser outlet to free inside edge of trim piece. Once I got it all loose job went very easy.
1 person
found this instruction helpful.
-
Dennis from Rogers, AR
- Difficult
- 30 - 60 mins
Use small putty knife to cut internal sealant on ice maker door trim piece. Then you can easily remove it.
Was this helpful?
Thank you for voting!