EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

TFX22PRXDBB General Electric Refrigerator - Instructions

All Instructions for the TFX22PRXDBB
46 - 60 of 257

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door Not Closing Tightly + Staying Open
4 of 8 people found this instruction helpful.
  • Jeff from Venice, FL
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Turned off water to ref , removed bottom kick plate , got a towel and disconnected the water line plastic fitting and un screwed the (2) tube clamps un screwed the coupling and ((carefully )) slid out the tube from the compression ferrels ! ( Be careful and do not break or distort them + remember exactly the order they are removed ! Sl id the protector spring shroud from the plastic tube , took ogg the top hinge cover then remover the top hinge . Carefully lifted the door off feering the plastic tube through the bottom hinge with my foot ! Got the door off removed the bottom hinge + put the new on on, then removed the door cam which was broken on the bottom of the door , lifted the door up and carefully fed the water line through the new bottom hinge . Attached the top hinge and reassembled the rest same as I had dissambled it . Turned on water ( checked for leaks ) ! All working 100% a-ok ! This company is the best ! Ordered the part at 1 pm and had the part at 2 pm the following day many thanks : )
Was this helpful?
Thank you for voting!
Door wouldn't close properly
2 of 2 people found this instruction helpful.
  • John from San Marino, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
First we removed the door. Then we had to hammer the old part off including the old rivot. We fould a screw that fit and put this piece on. We held the door in place and screwed the hinge on the main unit.
Was this helpful?
Thank you for voting!
Refrigerator door won't close
3 of 6 people found this instruction helpful.
  • CYNTHIA from NEWARK, DE
  • Easy
  • 15 - 30 mins
  • Wrench (Adjustable)
First I removed the top hinge of the refrigerator door and then lifted it off the bottom assembly. I had to turn the door on its side to work on the bottom where the broken part was located. I unscrewed the bottom assembly and replaced the broken part with the new door cam. Put it all back together and now the door closes but must be manu ally pushed to close. When the door was working properly it would shut automatically when released from any position. I think I need to install an additional part - maybe a shim? to make it close automatically. That will be another story.
This was a fairly simple jog to do but since I did not have the proper tools it did take me longer than usual to remove the bolts. I'm happy I did it myself and saved a big repair bill! Thanks to the people at PartSelect.com.
Was this helpful?
Thank you for voting!
Crushed Ice Only
2 of 3 people found this instruction helpful.
  • Allen from Hills, IA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
Let me start by saying, I usually hire something like this out but figured I would give it a try. The install was fairly straight forward, however it would’ve been nice if the instructions would have been more useful. Instructing me to remove one screw to release the auger and solenoid enclosure wouldve been nice. There were 3 other screw s that I didn’t need to remove and they were the ones holding the auger in place, which made assembling that much more difficult. Once to enclosure was removed, and the solenoid was exposed, it was a seemless process. I would however, recommend paying attention to or taking a picture of the connections on the solenoid. I was lucky to remember or got lucky. Regardless, I was able to complete the project successfully. If I had to do it again, I believe it can be done in 30 minutes or less.
Was this helpful?
Thank you for voting!
frost/ice buildup in icemaker chute in the freezer door
2 of 3 people found this instruction helpful.
  • Kyoko from Bellevue, WA
  • Easy
  • 30 - 60 mins
  • Screw drivers
The only difficult part was not knowing which parts had to be removed to gain access to the flapper to replace it. It appeared as if the frame around the control panel would have to be removed as well as the door handle; we tried but were not able to remove the frame. It turned out that the panel just popped out with the frame in place. O nce we had access to the flapper, it was easy to replace it. The repair fixed the problem.
Was this helpful?
Thank you for voting!
No water through door dispenser
2 of 3 people found this instruction helpful.
  • Roger from Colleyville, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Replaced flapper valve per website instructions. GE factory technician took two weeks to get here, charged over $100 for the call and told us we needed a new refrigerator door at a cost of over $500 to fix the problem. We sent him packing. After visiting the PartSelect website, the $5.88 PartSelect flapper valve fixed the problem. Ama zing.
Was this helpful?
Thank you for voting!
Door closing cam split in two and door would not automatically close anymore.
1 person found this instruction helpful.
  • John from Salinas, CA
  • Really Easy
  • Less than 15 mins
  • Pliers, Socket set
This one is a no brainer… One Phillips screw on top to pull top door hinge trim. Two nuts and the top hinge is free. Then pull the door… it helps if you unload all the crap in the door bins. Remove the remnants of the door cam and that leaves a pop rivet. Put some vise grips on the head and use a hacksaw to remove the lower part of th e rivet. Then pop-rivet the new door cam in place. If you don’t own a pop-rivet tool, I guess you could use a 10/32” screw and nylock. Plop the door back on and you’re done. Took all of about 15 minutes.
Was this helpful?
Thank you for voting!
Bulb burned out.
3 of 7 people found this instruction helpful.
  • Jimmie from Surprise, AZ
  • Really Easy
  • Less than 15 mins
Screwed new bulb in socket
Was this helpful?
Thank you for voting!
drawer facing cracked
3 of 7 people found this instruction helpful.
  • Christine from Delray Beach, FL
  • Really Easy
  • Less than 15 mins
ordered drawer face - perfect part- snapped right in. done. order came within 10 days.
will order again if needed.
Was this helpful?
Thank you for voting!
The light bulb in my freezer door burned out.
1 person found this instruction helpful.
  • Peter from HAZELHURST, WI
  • Very Easy
  • Less than 15 mins
Remove the burned out bulb and install the new light bulb.
Was this helpful?
Thank you for voting!
The light inside the oven had burned out
3 of 7 people found this instruction helpful.
  • Catherine from SEATTLE, WA
  • Very Easy
  • Less than 15 mins
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap. ... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.
Was this helpful?
Thank you for voting!
My ice container and Ice chute were freezing up and getting blocked, and my filtered water line was also freezing
1 person found this instruction helpful.
  • Joe from BRICK, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I just followed the instructions on the video and it was exactly as they said......no surprises.
Was this helpful?
Thank you for voting!
GE vegetable drawer broken.
1 person found this instruction helpful.
  • Philip M. from SIMPSONVILLE, SC
  • Very Easy
  • Less than 15 mins
Concerned about removing and attaching front panel to broken drawer. Rep. said wasn't sure but most just snapped together. Rep. was correct. No tools required.
Was this helpful?
Thank you for voting!
Door wouldn't close tight.
1 person found this instruction helpful.
  • charles from moundville, AL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
I placed books under the door until I had enough to hold the door up about 1/2 inch higher then when it is closed. The books and the magnetic gasket will hold the door, JUST DON'T TRY TO OPEN IT TILL YOU'RE THROUGH. That's about how high the cams lift the door when opened. I removed the two screws holding the door stop. Then removed the two screws holding the lower hinge pin.

It takes two of the cams

and the bottom one is riveted to the hinge. I used a grinder to grind the rivet so I could tap the pin out holding the cam. Put the new cam on and put the pin back in. I didn't put a new rivet, just gravity should hold it. I put the second cam on the hinge pin and one of the screws on the door stop holds it in place after you slide the hinge pin back into the door and replace the screws in the bracket then the door stop.
Make sure your lower door gasket didn't get damaged while the cams weren't working because the door wasn't being lifted up when opened.
Was this helpful?
Thank you for voting!
Door Would Not Shut
1 person found this instruction helpful.
  • Chris from Lecanto, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
Same problems as already described .... door would not close, plastic bits on floor, angry, ready to throw-out 15 year old “dog” and blow at least $1,000 on a new appliance!

This repair is dead easy. Remove the two bolts holding the top hinge and lift off the entire door. Don’t be surprised if the original Riser Cam has virt ually disintegrated, mine was a wreck. Remove two bolts that retain the old flat metal “shim” and fiber “gasket”.

Fit new Riser Cam and re-use old shim and gasket. Replace door on dome-shape bottom hinge mount and then re-fit top hinge.

If in any doubt order new shim and gasket along with the new cam riser. Or, do as I did, and “manufacture” either of these parts from scrap material found in the workshop ....
Was this helpful?
Thank you for voting!
All Instructions for the TFX22PRXDBB
46 - 60 of 257