EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

TFG27ZFTCWH General Electric Refrigerator - Instructions

All Instructions for the TFG27ZFTCWH
16 - 30 of 121

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Light Shield Broke Off
2 of 3 people found this instruction helpful.
  • Travis from Hillsboro, OR
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The light shield is only held in with a single screw, so it was the simplest install ever - unscrew the old light shield (in my case, the remaining piece of the light shield), put the new shield in place, and screw it down. Doesn't get any easier than that.
Was this helpful?
Thank you for voting!
The freezer light shield was broken.
2 of 3 people found this instruction helpful.
  • Fred from Union, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I removed the ice maker,removed the broken piece of the old light shield,screwed the new light shield in place,and replaced the ice maker.It took all of 5 minutes.
Was this helpful?
Thank you for voting!
No water through door dispenser
2 of 3 people found this instruction helpful.
  • Roger from Colleyville, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Replaced flapper valve per website instructions. GE factory technician took two weeks to get here, charged over $100 for the call and told us we needed a new refrigerator door at a cost of over $500 to fix the problem. We sent him packing. After visiting the PartSelect website, the $5.88 PartSelect flapper valve fixed the problem. Ama zing.
Was this helpful?
Thank you for voting!
frost/ice buildup in icemaker chute in the freezer door
2 of 3 people found this instruction helpful.
  • Kyoko from Bellevue, WA
  • Easy
  • 30 - 60 mins
  • Screw drivers
The only difficult part was not knowing which parts had to be removed to gain access to the flapper to replace it. It appeared as if the frame around the control panel would have to be removed as well as the door handle; we tried but were not able to remove the frame. It turned out that the panel just popped out with the frame in place. O nce we had access to the flapper, it was easy to replace it. The repair fixed the problem.
Was this helpful?
Thank you for voting!
Watched video on flapper assembly replacement looked real ready. Video failed to mention ice dispenser trim was glued in place . Had to buy real small paint scrapper that would fit in dispenser outlet to free inside edge of trim piece. Once I got it all loose job went very easy.
1 person found this instruction helpful.
  • Dennis from Rogers, AR
  • Difficult
  • 30 - 60 mins
Use small putty knife to cut internal sealant on ice maker door trim piece. Then you can easily remove it.
Was this helpful?
Thank you for voting!
Warm air enters ice dispenser on door
1 person found this instruction helpful.
  • J Stephen from BETHESDA, MD
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Replaced flapper. Followed the video. The lamp caused the removable plastic bracket (which supports the control panel and the ice chute) to fuse with the plastic frame in the door. Eventually broke the fused plastic, removed the bracket, and filed the rough broken plastic before reassembly.
Was this helpful?
Thank you for voting!
Remove front cover
1 person found this instruction helpful.
  • Philip from S BURLINGTON, VT
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Remove front cover did not remove wires remove ice and water unit took off flapper put new one on 5 minutes back together
Was this helpful?
Thank you for voting!
On the water dispenser line, the heat from the compressor unit had cracked the feed line, resulting in a leak.
1 person found this instruction helpful.
  • Walter from SANDIA PARK, NM
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
I removed the plate covering the water valve for the ice maker and water dispenser, removed the nut holding the 5/16" tubing to the valve and took off the tubing and nut. I did not need to turn off the water supply or unplug the unit. I removed the kick panel in the bottom front of the refrigerator, replaced the existing plastic fitting w ith a new push-on fitting, then spliced the tubing coming from the water chiller to the valve where the leak was thus bypassing the broken tubing with new tubing. I reassembled the valve using the original plastic compression nut, replaced the cover and ran the water dispenser while checking for leaks. The water dispanser works great with no leaks.
Was this helpful?
Thank you for voting!
Original part cracked allowing crushing fingers to grab plastic guide jamming it.
1 person found this instruction helpful.
  • Barry from SUN VALLEY, CA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Part attaches to metal plate near crushing fingers which attaches to ice holding bin. Remove about 6 screws total on each side of plate. You must disassemble the auger & other parts so you can reassemble it in the proper order. Not many parts but i always take pics to cut down on time. New part is at the other end of the auger and acts a s the holde of the auger shaft. Picture a crankshaft with a bearing on each end so the auger rotates between new part and the other end of auger shaft. That's it.
Was this helpful?
Thank you for voting!
Ice Crusher began to leave plastic in ice
1 person found this instruction helpful.
  • Richard from BONAIRE, GA
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers
We only needed the rear plastic cylindrical helix. After installing it, there was a squeal of metal on metal due to insufficient clearance between the rear moving blade and the Ice dispenser plate.

Refrigerator Ice Maker 7/16” (or ½” hole, stainless steel) washer just behind #334 Rear Moving dispenser Blade PS292310 to give clearance so it doesn’t hit #345 / PS292441 Ice Dispenser Plate.

This was my first time at doing this so it took longer than someone experienced. But, it worked!
Was this helpful?
Thank you for voting!
Thought flapper in ice dispenser was problem. - more serious, more costly - not a DIY! New fridge here we come!
1 person found this instruction helpful.
  • Gail from LEXINGTON, SC
  • Very Difficult
  • More than 2 hours
Opened, discovered not flapper but more complicated
Was this helpful?
Thank you for voting!
My ice container and Ice chute were freezing up and getting blocked, and my filtered water line was also freezing
1 person found this instruction helpful.
  • Joe from BRICK, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I just followed the instructions on the video and it was exactly as they said......no surprises.
Was this helpful?
Thank you for voting!
Freezer Light Shield Cracked at mid fastening point
1 person found this instruction helpful.
  • George V. from PITTSBURGH, PA
  • Very Easy
  • Less than 15 mins
replaced the broken one with the new part
Was this helpful?
Thank you for voting!
Plastic guide in rear of bucket broke it guides auger when dispensing ice
1 person found this instruction helpful.
  • Robert from FIFE LAKE, MI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I simply removed 6 screws that held bucket to face and pit on new bucket and put it back in freezer works great
Was this helpful?
Thank you for voting!
Had a drip which filled up the tray and leaked on the floor from water dispenser
1 person found this instruction helpful.
  • Rudy from CITRUS SPGS, FL
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
There are Great videos on YouTube!!! Turned off power,Removed trim ring, Pushed a philips head screwdriver in one of the holes underneath the electrical panel with the selector push buttons. This releases the electrical panel. There are Three wire sets with plugs. I removed the plugs and took the electrical panel out. Removed four Phillip s head screws and pulled out the big paddle switch. This then exposes the flapper. Replaced flapper with new one and reassembled everything. When I had everything apart, I cleaned with window cleaner. It was pretty moldy from the water leaking. Turned power back on and tested everything to make sure I didn't mess anything up. Works great
Was this helpful?
Thank you for voting!
All Instructions for the TFG27ZFTCWH
16 - 30 of 121