EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

TES355MQ2 Estate Range - Instructions

All Instructions for the TES355MQ2
121 - 135 of 204

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven not heating properly
0 of 1 people found this instruction helpful.
  • Matthew from Greenville, OH
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Unplug the oven, pull it out and empty the inside of the oven. The bottom heating element just unscrews from the back of the oven with two screws. Pull it out from the back of the oven and gently pull off the electrical connections. Reattach them to the new heating element, put it back into the oven and reattach the screws. Turn the o ven on and check to make sure that the new heating element is working. Put everything back in the oven and you're done!
Was this helpful?
Thank you for voting!
Light burned out in upper oven
0 of 1 people found this instruction helpful.
  • Shirley from Las Vegas, NV
  • Really Easy
  • Less than 15 mins
Screwed in light bulb and glass protector
Was this helpful?
Thank you for voting!
replaced oven lightbulb
0 of 1 people found this instruction helpful.
  • peggy ann from forest city, NC
  • Really Easy
  • Less than 15 mins
very easy
Was this helpful?
Thank you for voting!
Oven gets too hot,if set at 350 it heats to 550. Changed the sensor and was not the problem.
0 of 2 people found this instruction helpful.
  • Joanne from Negaunee, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took off the screws on the back of the stove and took out the sensor, and put in the new one.
Was this helpful?
Thank you for voting!
Bulb Replacement
0 of 2 people found this instruction helpful.
  • Judith from Phoenix, AZ
  • Really Easy
  • Less than 15 mins
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this helpful?
Thank you for voting!
water pump went out
2 of 12 people found this instruction helpful.
  • paul from windsor, VA
  • Really Easy
  • Less than 15 mins
  • Pliers
it was very easy i took the pump off only two clips and two hoses holding it type in the model number at parts select it came right up soi new it right one from the picture got with in 3 days put it back on less then 10 mins
Was this helpful?
Thank you for voting!
Both outside door handles turned very beige
23 of 76 people found this instruction helpful.
  • Howard from Boynton Beach, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol oring refer handles. Thank you
Was this helpful?
Thank you for voting!
Replacing the Upper Spray Arm, part # PS2581378
  • Vittorio from Wakefield, MA
  • Really Easy
  • 15 - 30 mins
The detection of the part and the replacement of the upper spray arm was quite easy, because of its unique shape and function, and also because it was easy to screw in place. I saved the web order page in case this part tends to deteriorate frequently, even though it is the first time it showed this problem since we purchased this applian ce.
Was this helpful?
Thank you for voting!
E-2 F-3 codes..Oven inop w/trying to bake.Beeps @ start attempt.
  • Dave from Titusville, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.
Was this helpful?
Thank you for voting!
Burner Would,Nt Heat Up.
  • david from cleveland, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed top of stove replaced heating element ,piece of cake.
Was this helpful?
Thank you for voting!
The Terminel Bloc Overheated And The Bloc Melted Causing The Stove To Cease Fukshioning
  • Joseph from Channelview, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
R&r
Was this helpful?
Thank you for voting!
lower element burned out
  • Ann from Weston, WI
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
So easy. Unplug the range. (really important. You're working with wiring after all) Unscrew the metal plate holding the bake element in place, gently pull out the wires and detach the element from them. (the element just pulls off, but it was attached pretty tightly so I did have to use needlenose pliers to get a better grip on it.) The n simply plug in the new bake element, push the wires back in, reattach the metal plate and bake a cake! Don't even think about calling a repairman for this one! It took under 10 minutes once I got around to ordering the element. (none of the local stores carried them)
Was this helpful?
Thank you for voting!
Terminal Block was melted where the cord had came lose.
  • Louise from Humansville, MO
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed the therminal block and put the new one in.Using a screwdriver, very easy repair.
Was this helpful?
Thank you for voting!
burned out upper element
  • jack from kalispell, MT
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
turn the light on in the oven go to the breaker box and shut off power to the oven when light is out is good indicator remove two screws in back of oven that secure element to back then remove two screws on top inside the oven to almost finish removal. phillips head screwdriver and needle nose pliers and two small spring loaded clamps are all you will need to accomplish thismove the upper element side to side until the connectors are exposed in the back of the stove pull the two wires out about 4 inches should be enough place the spring loaded clamps on each wire so as to not allow them to slip back in the stove body. take the needle nose and while holding the clamp remove the connector from each wire once this is done place the new element in the stove and reconnect the clips on the end off the element move the wires and connectors back into the openings on the stove and replace the two screws replace the two upper screws check all screws for tightness go to the breaker box and turn on the power takes about thirty minutes
Was this helpful?
Thank you for voting!
oven temperature did not stay as set
  • Paul from Cornelius, NC
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.
Was this helpful?
Thank you for voting!
All Instructions for the TES355MQ2
121 - 135 of 204