SCA1000DBB03 General Electric Microwave - Instructions

I held the door open while the repair man took the black facing off and replaced the latch and reinstalled the facing I was worn out

Removed the door, removed the old choke cover (breaking all the stap catches), removed the slide door latch assembly from the spring (the most difficult task) then reassembly of the latch to spring, sliding into the grooves along the inside of the door, the installing the new choke cover (very easy with the new one) taking care not the break any of the staps. Easy enough! Another difficult task was to re-install the door to the frame. It appears that the lower "hinge" is slightly bent down to allow easy install but the door now makes a slight sweeking sound when opening and closing.

removed cover an replaced

Unpacked glass plate from cardboard box and placed atop rotating spindle inside oven - done.

I'm writing because I have never in my life had such an easy time finding a part, ordering it, and receiving it! Your service is truly unbelievable. I still don't believe it and I experienced it. Nothing went wrong and it could not have been easier. Please don't go away.

Placed the new tray in the microwave.

Opened the lid over the bulb by removing one screw. Removed old bulb; a bayonet type with delicate prongs. Inserted new bulb. Best to turn off circuit breaker toi the micro for safety reasons.

I went on line and found the part and read all the comments that had been written on how to repair the door and I found the directions on how to take it off and put it back on, so it helps to do your research on taking it off and putting another one. My son-in-law did it for me, it was quite difficult to remove the screws,and it took about 30 min to remove the door and take the screws out, but putting it back on was easy and took less than 5 min. So I was pleased, the part was ordered on Sat and came by FX on Tuesday, I was very happy with the service, and it works as good as new. Just do your research, that helped a lot.

Called my local appliance repair shop when the handle broke off my GE Advantium microwave. They told me the price of the handle, but said the door would need to be replaced as well. This is because the plastic tabs break off the inner door panel when it is removed. They estimated a $400 repair cost. I ordered the door and installed it for around $45. The inner panel comes out, and most of the tabs do break off. I was able to disassemble, install the new door, and reassemble. The inner panel stays right where it belongs, even though I broke off a few plastic tabs. Werks goood.

opened the access door. It took some tugging to get the old bulb out, and is was awkward getting the prongs on the replacement bulb lined up and pushed in, but it was accomplished in about 10 minutes. You had exactly the right information on a change in the part number that was made by GE, and you shipped the correct bulb the same day I ordered it.Good job. N R Brown

This is the tray the glass cooking tray rest on and rotates the glass during cooking. The metal tray was installed upside down. The rotating glass tray was not properly installed. The oven was at a very high temp. and the weight of the utensil on the glass was not supported correctly. Result, big " pop " and broken glass tray. Note this is the second glass repaced. The first one dropped while removing it from the oven. It stuck to the bottom of the cooking dish and then fell to the floor. Pop, big breakage. Maybe you can learn from my mistakes.

Our GE Profile Advantium 120 Series Over-the-Range Microwave stopped working. We called GE Service. The first available appointment was two weeks after our call. The technician charged $99, gave us a form stating that the Magnetron and Diode Cable as defective and quoting an additional price of $362 to furnish and install these parts. He said that it would be another two weeks before he could do the work. Instead I ordered the parts from you and had them within two days. The parts you furnished were identical to the original parts in our unit. They arrived within two days. I installed the parts without removing the microwave from the wall. The most difficult part was inserting the magnetron mounting screws into openings in the rather tight space available. I was able to do this by using plastic pacaging tape to hold the screws onto the end of a short Phillip screw, Prior to iserting each screw I pushed it through the sticky side of a piece of packaging tape. I then folded the sticky surface over the shank of the screw. Once a screw was seated, but before it was fully tightened, I used needle nose pliers to pull off the tape. The unit now functions perfectly.

Unscrewed the two connecting points, cleared out the broken bits of plastic, mounted the new grille and screwed the two screws back in. Easy. Also, the new part arrived very quickly.

The instructions were great!!! It was difficult to take the face plate off without breaking the nibs off that hold it in place. Other then that the only issue I had was removing the broken piece that was cemented in place by the years of super glue. Had to drill it out and almost drilled out the receiver plate to hold the screw/handle in place. I have to say this saved me $400 because I was just about to buy a new microwave because the broken door handle had driven me crazy over the last 3 years.

Quick and easy repair. I also want to comment on the very helpful telephone assistance from your customer service rep and the very fast shipping. You are a wonderful Company to do business with