RVRF3361SS4 Frigidaire Refrigerator - Instructions

Removed the two screws that hold the element in place. Then I pulled the element out about 3 inches and disconnected the wires. Everything matched up perfectly.

I shut the water off under the sink and removed the back piece on the refrigerator, unscrewed the water valve, cut the ends off each plastic hose and reinserted into the new water valve. Then rescrewed the water line into the new water valve and turned on the water. Unfortunately, I was not able to get water out of the door and the ic ... Read more e maker still doesn't make ice. While this was an easy procedure, it didn't help me. I'm not sure I needed to replace the water valve.

Pulled the old gasket out if groove on the door, cleaned inside the groove, squirted some windex in the groove to ease the new gasket in the groove, then proceeded to work the gasket into the groove. Made sure gasket was all the way in the groove around the perimeter of the door. Done!

It's too easy to describe.

What's more important is that someone read this and see that you can save hundreds of dollars doing this repair yourself. I'm sure many handy people think that about everything they repair, but this repair is insanely easy and the $ savings ridiculous.
Wh ... Read more en I called the place I purchased the refrigerator from, they were more than happy to sell me the part with a 35% markup (your price was reasonable) and (when i asked) they told me that sending someone to my home to make the repair would cost about $400 ($200 per door) including the "home instal" fee.
I removed the old gaskets and put on the new ones (on both doors) in under 10 minutes. I confess that I did the job under the auspices of my very handy son but he'll agree with everything I just wrote. To the unhandy: go forth and replace your own gaskets.

I replaced the water valve, but it still did not fix the problem.The old water valve I took out I'm assuming worked fine, I think the real problem is ice building up in pipe or some other blockage.

Parts select was very fast in shipping, very positive experience with them.
I will definitely purchase again from this site.

Followed instructions from others on the blog. Shut off water and electricity to the refrigerator. Removed the cardboard plate. Removed the old water valve. Cut the compression valves off and inserted the tubes into the new water valve. Attached the water valve bracket to the fridge. Tightened copper water supply.Turned on the water ... Read more - no leaks. Plugged the fridge in. Tried the water and ice in the door. No leaks - everything worked perfectly. THANK YOU PARTS SELECT!

removed rear cover, removed screws, diconnected water line connections, cut off old water line connection, installed new compression water line connection, replace screws in water line housing, replace rear cover.

worked fine

We followed the video instructions and it went fairly smooth. After turning off the water at the street we found that the faucet at the wall had it's own "on/off" valve. When finished, we turned on the power and heard the gears going through their revolutions, but no ice was made. We waited 24 hours and still no ice. I removed the cover o ... Read more n the ice maker and adjusted the amount of water to see if that was malfunctioning. Still no ice was created. Waited another 24 hours - nothing. Waited another 24 hours (the site said that sometimes the ice maker would take time to reset itself) - nothing. Then on the fourth day after changing out the triple water valve we heard water being dispensed and later that day it put out the first ice in weeks. Another hour later another batch of ice cubes were ready and deposited into the bin. Since that time, we have had a full bin. I moved the set screw back to it's original setting because a little too much water was being delivered. The cubes weren't separating to individual cubes. That cleared up the problem. This was easily completed - we recommend others do their own work. Just be patient for the system to reset itself.

Took drawers out by removing 2 screws on top of rail near front, then popped black plastic cover off in lower right inside cabinet...sensor just un plugged and new one plugged in easily...did not fix problem though...display set at 34 but bottom drawer reads about 40 at best and upper drawer reads around 55...dont think the 3 little fans ... Read more inside on back wall have been running

Replace gasket

Remove old gasket by pulling it away from the frame. Work all the way around the gasket till it is entirely separate from the door. Remove the old gasket by slipping it over the door. Note the orientation of the new gasket will have the small bead towards the door - slip the new gasket over the door so that it is in the inside of the f ... Read more reezer door. Press the small bead into the slot in the door. Work all the way around, pressing the bead in with your fingers. When it's all secure, close the door and check for no gaps. Takes 5 minutes and no tools - very easy. Make sure you order the correct COLOR of gasket - it comes in black and white. The black looks best on stainless steel door.

Replaced the Triple Water Valve

From discussions with friends, I determined the problem might be easy to fix. The fridge made a lot of noise, but the compressor DID come on, and inside the freezer was cold, but the main fridge was warming.

After unplugging the fridge, I removed the fan assembly in the freezer (there were about 4 nuts and a couple of plugs to ... Read more uncouple.

I could see right away the fan blades has broken off, but the motor looked good. The new new fan pushed easily onto the shift and fit perfectly in the housing.

I reinstalled the fan assembly, plugged in the fridge, and right away heard the new fan come on - very quietly. What was a roar became a whisper and the fridge was down to 38 degrees with a few hours.

The instructions that were provided were perfect. Easy step by step. Entire installation took only 15 minutes

Pulled the unit out from the wall and with a flat head screwdriver and a utility knife I replaced the valve assembly. It was no problem at all.